SUSWE suswe-750

Contents

SUSWE 750W VFD Frequency Converter

Model: suswe-750

1. Introduction

This manual provides essential information for the safe and effective use of the SUSWE 750W VFD (Variable Frequency Drive) Frequency Converter. This device is designed to control the speed of 3-phase AC motors from a single-phase 220V AC input, offering precise motor fan speed regulation, constant pressure water supply control, and energy-saving capabilities. It features a vector overload type control and a user-friendly interface for various industrial and domestic applications.

Video: Demonstration of the SUSWE VFD controlling a motor and adjusting frequency.

2. Specifications

FeatureSpecification
Model Numbersuswe-750
TypeDC/AC Inverter
Input VoltageSingle Phase 200V-240V AC
Output Voltage3 Phase 200V-240V AC
Input Frequency50/60Hz
Output Frequency Range0-99Hz
Output Power750W (0.2kW ~ 0.75kW)
Weight0.5 kg
Dimensions (L*W*H)130mm * 60.5mm * 102.5mm
Opening Size for Installation130mm * 52.5mm * 80mm
Output TypeSINGLE
OriginMainland China
CertificationCE, FCC, RoHS
SUSWE VFD Dimensions

Figure 2.1: Product Dimensions

3. Product Overview

The SUSWE VFD features a compact design with an intuitive control panel and clearly labeled terminals.

3.1 Control Panel

Control Panel Layout

Figure 3.1: Control Panel Layout and Key Functions

  • Display Area: Shows frequency, current, and other operational parameters.
  • MODE Key: Used to view set frequency (Fxxx), operating frequency (Hxxx), operating current (Axxx), motor direction (FWD/REV), input voltage (Uxxx), inverter temperature (Txxx), input point status (Lxxx), and PID parameter display (X.X-X.X).
  • Up Key (▲): Adds function when setting data or increases frequency when controlled by the panel.
  • Down Key (▼): Subtracts data function when setting data or reduces frequency when controlled by the panel.
  • ENTER Key: Enters parameter mode when setting Pxxx parameters and saves the set parameters after modification.
  • JOG Key: Initiates jog operation function.
  • RUN Key: Starts inverter panel operation.
  • STOP / RESET Key: Stops operation mode and clears fault alarm function in fault display mode.
  • Potentiometers: Used for regulating frequency.

3.2 External Terminals

External Terminals View

Figure 3.2: External Terminals

The VFD is equipped with various terminals for power input, motor output, and control signals. Refer to the wiring diagram in Section 4 for detailed connections.

4. Installation and Wiring

Proper installation and wiring are crucial for the safe and correct operation of the VFD. Ensure all power is disconnected before proceeding with installation or wiring.

4.1 Mounting

The VFD is designed for panel mounting. The recommended opening size for installation is 52.5mm (width) x 80mm (height) x 130mm (depth).

Opening Size for Installation

Figure 4.1: Installation Opening Size

4.2 Wiring Diagram

Connect the VFD according to the following diagram. Pay close attention to input power, motor connections, and control signals.

Detailed Wiring Diagram

Figure 4.2: Detailed Wiring Diagram

4.2.1 Power and Motor Connections

  • L, N: Single-phase 220V AC input.
  • PE: Ground connection. Ensure proper grounding for safety.
  • U, V, W: Three-phase output to the AC motor.

4.2.2 Control Terminals

  • CM, NC, ON: Relay output terminals.
  • YO: Multi-function composite output point. Can be configured as a brake resistor or general transistor output.
  • X0, X1, X2, X3: External sensor inputs.
  • 12V, GND, 5V, AI, A+: Analog input terminals. Supports 0-5V or 0-10V analog input. For 4-20mA input, an external 250Ω resistor is required.
  • B-, A-: RS485 communication terminals.
Wiring Label Indication

Figure 4.3: Wiring Label Indication

5. Operation

The VFD features a user-friendly operation interface. Follow these steps for basic operation:

5.1 Power On and Initial Setup

  1. Ensure all wiring is correct and secure.
  2. Apply single-phase 220V AC power to the L and N terminals.
  3. The display will light up, showing the current status or default frequency.

5.2 Frequency Adjustment

  • Using the Potentiometer: Rotate the potentiometer knob on the control panel to adjust the output frequency (and thus motor speed) from 0 to 99Hz.
  • Using Up/Down Keys: In certain modes, the Up (▲) and Down (▼) keys can be used to fine-tune the frequency.

5.3 Starting and Stopping the Motor

  • Start: Press the green RUN key to start the motor.
  • Stop: Press the red STOP / RESET key to stop the motor. This key also clears any active fault alarms.

5.4 Parameter Setting

The VFD allows for advanced configuration through its parameter settings. Refer to the detailed key description for navigation.

Key Description for Parameter Setting

Figure 5.1: Key Description for Parameter Setting

  1. Press the ENTER key to enter parameter mode. The display will show 'Pxxx'.
  2. Use the Up (▲) and Down (▼) keys to adjust the parameter number.
  3. Press ENTER again to modify the selected parameter's value.
  4. Use the Up (▲) and Down (▼) keys to change the value.
  5. Press ENTER to save the new value.
  6. If the panel does not display 'Pxxx', press the MODE key until 'Pxxx' is displayed.

5.5 Advanced Features

  • V/F Curve Function: The VFD supports customizable V/F curve settings to meet specific application requirements.
  • Real-time Parameter View: Use the Shift key to cycle through and view real-time operational parameters.
  • Built-in Intelligent Logic Controller: Enables simple logic control functions for automated tasks.

6. Troubleshooting

This section provides a guide to common fault codes and their remedies. If a fault persists, contact technical support.

Fault Code Table

Figure 6.1: Fault Code Table

Alarm TypeFault DescriptionFault Comment
OCInstantaneous overcurrentCheck whether the motor is normal.
OCAAcceleration overcurrentAdjust the acceleration time appropriately.
OCDDeceleration overcurrentAdjust the deceleration time appropriately.
OCNConstant speed overcurrentAdjust the deceleration time appropriately.
OUOverpressureCheck whether the machine is normal and the voltage is stable.
LUUndervoltageAdjust the acceleration and deceleration time properly, and check whether the mains supply is normal.
OHInverter overheatingDetect whether the mains supply is normal (180V-240V).
EFExternal faultDetect external sensors. Whether the input is normal.
ERSFailure restart failedCheck whether the input is normal.
LPInput phase failureRestart the drive.
OL1Motor overloadCheck whether the mains supply is normal.
OL2Inverter overloadCheck whether the motor is normal and whether the load is too heavy.
OL3Temporary motor overloadCheck whether the motor is normal and whether it matches the frequency converter power.
OL4Temporary overload of frequency converterCheck whether the load matches the motor.
485Communication failureCheck whether the communication line is normal, and whether the upper computer communication is normal.
PIDPID failureCheck whether analog input is output and whether sensor is normal.
NONo fault alarmCheck whether analog input is output and whether sensor is normal.

7. User Tips

  • The VFD is designed with a user-friendly interface, making parameter setting straightforward. Take advantage of the potentiometer for quick and easy speed adjustments.
  • For optimal performance and safety, ensure that the motor's power rating is compatible with the VFD's output power (0.2kW to 0.75kW).
  • Always double-check wiring connections before powering on the unit to prevent damage or malfunction.

8. Warranty and Support

The SUSWE 750W VFD Frequency Converter comes with a 1-year warranty, ensuring quality and reliability.

8.1 Technical Support

For any technical assistance or debugging guidance, 24-hour one-to-one support is available. Remote package debugging services are also provided to help resolve complex issues efficiently.

SUSWE VFD with Warranty and Support Information

Figure 8.1: Warranty and Support Information


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.