1. Disclaimer
This product is intended for research and learning purposes only. Users are responsible for using this product reasonably and compliantly. The manufacturer is not responsible for any disputes or consequences arising from the use of this product.
2. Product Overview
The HamGeek Zynq7010+AD9363 SDR Development Board is an advanced Software Defined Radio platform designed for a wide range of applications, from research to development. It features significant improvements over previous versions, offering enhanced stability and functionality.
2.1. Key Features and Improvements
- Frequency Range: 70MHz to 6GHz.
- Chipset: Zynq7010 FPGA and AD9363 RF Transceiver (firmware hacked to AD9361 for extended capabilities).
- Memory: 1GB DDR.
- Storage: N25Q128 FLASH for booting, and one channel SD card slot for additional storage and booting.
- Connectivity:
- PS end USB2.0 port.
- PS end Gigabit Ethernet port.
- Integrated FT2232 debugger with serial port functionality.
- JTAG port for power supply, FPGA debugging, and serial port functions, also used for boot information output and IP configuration.
- RF Capabilities: Dual transmitting and receiving, support for external local oscillator input, and a reference clock input interface.
- Power Supply: Improved power supply stability.
- External Clock: Added 9363 external input clock interface.
- Board Size: Approximately 5 x 8 cm.
2.2. Supported Software
This development board is compatible with various SDR software platforms that support libiio, including:
- IIO Oscilloscope
- SDR Sharp
- GNU Radio
- MATLAB
3. Package Contents
Upon receiving your package, please verify that all items listed below are included. If any damage, collision, or water immersion is observed on the SDR motherboard, please contact customer support promptly.
3.1. Included Items
- SDR board: 1 unit (v0.38 firmware pre-loaded onto the SD card and inserted into the board).
- ZYNQ7010/20 heat sink: 1 unit.
- AD936X heat sink: 1 unit.
- FM antenna: 1 unit.
3.2. Items to Prepare (Not Included)
The following items are required for testing and operation and must be prepared by the user:
- Windows Computer: 1 unit.
- Type-C Cable: 1 unit.
- Network Cable: 1 unit.
- SMA Loop Cable (SMA-J): 2 units.
4. Setup and Initial Configuration
4.1. Drive Installation
Before connecting the SDR board, install the necessary drivers on your Windows computer:
- Locate the data package provided with the product, specifically the "software and drivers" folder.
- Navigate to the "USB virtual network port driver" subfolder.
- Double-click the installer file, typically named
PlutoSDR-M2k-USB-Drivers.exe. - Follow the on-screen prompts to complete the installation. This usually involves accepting the license agreement and clicking "Next" and "Install".
4.2. SDR Board Function and Interface Overview
The SDR development board features several key interfaces:
- Gigabit Ethernet Port: Supports functions similar to ZEDBOARD + FMCOMMS2-3.
- JTAG Port: Provides power supply, FPGA debugging, and serial port functions. In field firmware, it serves as the boot information output and for configuring IP.
- RF SMA Connectors: For transmit (TX1A, TX2A) and receive (RX1A, RX2A) signals.
- SD Card Slot: For storage and booting.
- USB Port (Type-C): For power supply and communication.
- BOOT Switch: For selecting boot mode.
- Reset Button: For restarting the board.
- LED Indicators: DONE, PWR, USER LEDs for status indication.
4.3. Initial Board Power-on and IP Configuration
Follow these steps to power on the SDR development board and configure its IP address:
- Check SD Card: Ensure the SD card (with v0.38 firmware) is correctly inserted into the board.
- Check Dip Switch: Verify that the dip switch is set to "00" (all facing down), which is the default for shipment.
- Prevent Short Circuits: Ensure the board is not in contact with any other metal conductors.
- Connect Ethernet: Connect your computer to the board using a network cable.
- Connect Power/JTAG: Insert the Type-C cable into the JTAG port on the board and connect it to your computer.
- Observe Startup: Wait approximately 30 seconds for the startup process to complete. A normal startup is indicated by:
- White and red LEDs remaining ON.
- Blue LED flashing.
- Ethernet port light flashing.
SDR Development Board connected via USB-C and Ethernet, showing power-on status. - Install Serial Port Software: If you don't have one, install a serial port software (e.g., SecureCRT, PuTTY) from the provided drivers or a trusted source. The provided driver package includes
SecureCRT5.5.zip. - Connect via Serial Port:
- Open your serial port software.
- Configure the connection settings: Baud rate 115200, Data bits 8, Parity None, Stop bits 1.
- Connect to the COM port associated with the SDR motherboard (check Device Manager for the correct COM port).
- Login: Once connected, you should see a login prompt. Enter:
- Account:
root - Password:
analog
- Account:
- Configure IP Address: After logging in, enter the following command to set the board's IP address:
ifconfig eth0 192.168.1.10 - Verify IP (Optional): You can perform a ping test from your computer's command prompt to verify connectivity:
ping 192.168.1.10Successful replies indicate the IP configuration is complete.
5. Operating Instructions
5.1. SDR# Software Testing
To test the SDR board with SDR# software:
- Connect Antenna: Connect the provided FM antenna to the RX1A RF interface on the SDR board.
- Prepare SDR# Software: Unzip the SDR# software package (e.g.,
SDRSharp_v1727.zip) from the software and driver folder. - Run SDR#: Double-click
SDRSharp.exeto launch the application. - Configure PlutoSDR in SDR#:
- In SDR#, click the "Settings" button.
- In the PlutoSDR Properties window, navigate to the "Connection" tab.
- In the "Device-URI" field, enter the IP address you configured for the board (e.g.,
192.168.1.10). - Click "Connect".
- Once connected, close the PlutoSDR Properties window.
- Start Reception: Set the desired interface parameters within SDR# and click the "Start" button.
- Tune to a Broadcast: Move the red line (frequency marker) to a peak position on the spectrum display to listen to broadcast audio.
5.2. IIO Oscilloscope Software Testing (USB Port)
To test the USB port and general functionality using IIO Oscilloscope software:
- Connect USB: Insert a Type-C cable into the USB port (not JTAG) on the SDR board and connect it to your computer.
- Observe Startup: Wait approximately 30 seconds for the board to start. The white and red LEDs should remain ON, and the blue LED should flash. Your computer may prompt for the insertion of storage devices.
- Prepare IIO Oscilloscope Software: Extract the IIO Oscilloscope software (e.g.,
IIO Oscilloscope.zip) from the software and driver folder. - Install IIO Oscilloscope: Double-click the installer and follow the on-screen instructions to complete the installation.
- Launch IIO Oscilloscope: Open the software. It should automatically detect and find the connected Pluto device.
- Configure Frequencies: Click on the connection and set the transmission and reception frequencies to be the same within the software interface.
- Set up Signal Transmission: Configure the FPGA settings, DDS, and TX1/TX2 parameters as needed for your test.
- Connect Loopback Cables: Connect TX1A to RX1A and TX2A to RX2A using SMA loopback cables.
- Enable Channels and Start: Enable the four channels in the software and click the "Start" button.
- Observe Waveform: You should observe the received waveform, which should be consistent with the set transmission waveform frequency.
6. Maintenance and Heat Management
The ZYNQ and AD936X components on the board have high power consumption, and due to the small board size, the device may generate heat during operation. This is normal.
Important: If the board needs to operate continuously for an extended period (more than 2 hours), it is highly recommended to prepare and install an additional cooling solution, such as a fan or a CNC heat dissipation shell, to prevent overheating and ensure stable performance.
7. Troubleshooting
If you encounter issues during setup or operation, consider the following common problems and solutions:
- Board not starting correctly (LEDs abnormal):
- Ensure the SD card is securely and correctly inserted.
- Verify the dip switch is set to "00" (all switches down).
- Check that the USB cable used for power is not too thin, as this can lead to insufficient current.
- Driver installation issues: Carefully re-follow the driver installation steps in Section 4.1. Ensure you accept all license agreements.
- No device detected in SDR software:
- Confirm the board is powered on and the LEDs indicate normal operation.
- Verify the Ethernet cable is securely connected and the network adapter on your PC is enabled.
- Double-check the IP address configuration (
ifconfig eth0 192.168.1.10) and ensure your PC's network settings are compatible. - Perform a ping test to the board's IP address to confirm network connectivity.
- Linux OTG connector not showing in dmesg: This can be a complex issue related to Linux kernel drivers or specific hardware configurations. Consult Linux community forums or the official HamGeek support for advanced troubleshooting.
- Excessive heat during operation: Refer to Section 6 for heat management recommendations, especially for continuous use.
8. Technical Specifications
| Feature | Specification |
|---|---|
| Model | Zynq7010+AD9363 SDR Development Board |
| RF Transceiver | AD9363 (firmware hacked to AD9361) |
| FPGA | Zynq7010 (XC7Z010-CLG400/XC7Z020-CLG400) |
| Frequency Range | 70MHz - 6GHz |
| DDR Memory | 1GB |
| FLASH Memory | N25Q128 |
| Interfaces | USB2.0 (PS end), Gigabit Ethernet (PS end), JTAG, SD Card, RF SMA (TX1A, TX2A, RX1A, RX2A), External LO Input, Reference Clock Input |
| Debugger | Integrated FT2232 (with serial port) |
| Board Dimensions | Approx. 5 x 8 cm |
| Power Consumption | High (cooling recommended for continuous use) |
9. User Tips
- Cooling is Crucial: As noted by other users, the board can heat up significantly during operation. For any continuous use, ensure adequate cooling with a fan or a heat dissipation enclosure to maintain performance and longevity.
- Software Installation Patience: Take your time with driver and software installations. If you encounter issues, double-check each step, especially IP configuration and serial port settings.
- Firmware Resources: Remember to contact customer service for the latest firmware resources after receiving your product.
10. Warranty and Support
For technical support, firmware resources, or any inquiries regarding your HamGeek SDR Development Board, please refer to the following contact information:
- Official Website: www.hgeek.com
- Email: hamgeek@163.com
An additional user manual in PDF format is available for download: User Manual (PDF).