1. Introduction
This manual provides detailed instructions for the proper installation, operation, programming, and maintenance of your Hobbywing QuicRun WP 10BL60 G2 60A Waterproof Brushless Electronic Speed Controller (ESC). Designed for 1/10 scale RC cars, buggies, and short course trucks, this ESC features advanced technology for optimal performance and durability. Please read this manual thoroughly before using the product to ensure safe and efficient operation.
2. Product Overview
The QuicRun WP 10BL60 G2 ESC is engineered for entry-level users, offering a simple yet high-quality solution for your RC vehicle. It boasts a compact design, intelligent freewheeling technology, an efficient heat dissipation system, and capacitor overheating protection.
Figure 1: QuicRun WP 10BL60 G2 ESC installed in an RC vehicle.
Key Features:
- Intelligent Freewheeling Technology: Effectively reduces heat generation, leading to higher driving efficiency and lower operating temperatures. This enhances the stability and reliability of the ESC.
- Capacitor Overheating Protection: Prevents capacitors from exploding due to overload, safeguarding the ESC from damage.
- Efficient Cooling System: Features a mesh-designed heat sink and copper thermal bars for each phase, ensuring optimal operating temperatures. A dedicated fan further aids in cooling.
- All-Weather Operation (IP67): The ESC is splash-proof, water-resistant, and dust-proof, allowing it to perform in various environments including rain, dust, and sand. Note: This protection is not permanently effective and may degrade over time. Do not submerge the product in water for extended periods.
- Compact Design: Shorter in length by 2.5mm and reduced in width by 1.5mm compared to its predecessor, facilitating easier installation in various chassis.
Figure 2: Intelligent freewheeling technology for reduced heat and improved efficiency.
Figure 3: Capacitor overheating protection mechanism.
Figure 4: Efficient cooling system with mesh heat sink and copper thermal bars.
Figure 5: All-weather operation capability (IP67 rated).
Figure 6: Compact dimensions of the QuicRun WP 10BL60 G2.
3. Specifications
Figure 7: Product Name and Number.
| Category | Parameter | Value |
|---|---|---|
| General | Product Name | QuicRun WP 10BL60 G2 |
| Product Number | 30102700 | |
| Type | Scale | 1/10th |
| Brushed/Brushless | Brushless | |
| Sensored/Sensorless | Sensorless | |
| Waterproof | Waterproof | |
| Electrical Specifications | Cont./Peak Current | 60A/380A |
| Input Voltage | 2-3s LiPo | |
| BEC Output | Switch Mode 6V/3A | |
| Wires & Connectors | Input Wires | Black-14AWG-150mm*1 (Red-14AWG-150mm*1) |
| Output Wires | Black-14AWG-150mm*3 | |
| Input Connectors | No | |
| Output Connectors | 4.0MM Gold (Female) | |
| Cooling Fan | Size | 25.0x25.0x10.0mm |
| Voltage Range | 5V | |
| Powered by | BEC | |
| Programming Methods | SET Button on ESC | Supported |
| LED Program Box | Supported | |
| LCD G2 Program Box | Supported | |
| LCD PRO | Supported | |
| OTA Programmer | Not Supported | |
| Program Port | Shared with fan port | |
| Data Recording | Extreme value | Not Supported |
| Real-time Data | Not Supported | |
| Historical data (Graph) | Not Supported | |
| Firmware | Firmware Upgrade | Supported |
| Physical | Size (L*W*H) | 48*38*22mm |
| Weight | 82.5g (Included wires/connectors) |
Figure 8: Detailed Specifications Part 1.
Figure 9: Detailed Specifications Part 2.
Figure 10: Applications Overview.
Applications:
- Motors: Sensorless / Sensored Brushless Motor (operates in sensorless mode only).
- Vehicles: 1/10th On-road, Buggy, Short course truck.
- KV Rating/T Count:
- 2S LiPo: KV ≤ 6000
- 3S LiPo: KV ≤ 3500 (for 3652/3660 size motors)
4. Setup
Proper installation is crucial for the performance and longevity of your ESC. Follow these steps carefully:
- Mounting the ESC: Securely mount the ESC in your vehicle using double-sided tape or screws, ensuring good airflow for cooling.
- Motor Connection: Connect the three output wires (Black-14AWG-150mm*3 with 4.0MM Gold Female connectors) from the ESC to your brushless motor. Ensure correct phase matching if applicable, though for sensorless motors, swapping any two wires will reverse motor direction.
- Battery Connection: Connect the input wires (Black-14AWG-150mm*1, Red-14AWG-150mm*1) to your LiPo battery (2-3S). Ensure polarity is correct (Red to positive, Black to negative) to prevent damage.
- Receiver Connection: Plug the ESC's throttle cable into the throttle channel (usually channel 2) of your RC receiver.
- Power Switch: Connect the external power switch to the designated port on the ESC.
- Initial Calibration: Perform throttle range calibration with your radio system according to the specific instructions provided by Hobbywing (often involving holding the SET button while powering on).
Figure 11: ESC with connected wires and external switch.
5. Operating Instructions
Once the ESC is properly installed and calibrated, you can begin operating your RC vehicle:
- Power On: Turn on your radio transmitter first, then connect the battery to the ESC and turn on the ESC's power switch.
- Self-Test: The ESC will perform a self-test and emit a series of beeps. Wait for the initialization sequence to complete.
- Driving: Use your transmitter's throttle trigger to control the motor speed. Push forward for acceleration, pull back for brake/reverse.
- Power Off: Always turn off the ESC's power switch first, then disconnect the battery, and finally turn off your radio transmitter.
6. Programming
The QuicRun WP 10BL60 G2 ESC supports various programming methods for parameter adjustment:
- SET Button on ESC: Basic parameter adjustments can be made directly using the built-in SET button. Refer to the detailed Hobbywing manual for specific button press sequences.
- LED Program Box: A dedicated LED Program Box (sold separately) can be connected to the ESC for easier parameter configuration.
- LCD G2 Program Box: For more advanced and visual programming, the LCD G2 Program Box (sold separately) offers a comprehensive interface.
- LCD PRO: The LCD PRO programming device (sold separately) provides the most extensive programming capabilities.
- OTA Programmer: Over-The-Air (OTA) programming is not supported for this model.
The program port is shared with the fan port. Ensure the fan is disconnected when using a program box.
Figure 12: Various programming methods for the ESC.
7. Maintenance
Regular maintenance will help extend the lifespan and ensure consistent performance of your ESC:
- Cleaning: After each use, especially in dusty or wet conditions, clean the ESC with a soft brush or compressed air to remove dirt and debris.
- Inspection: Periodically check all wires and connectors for signs of wear, fraying, or corrosion. Ensure all connections are secure.
- Waterproof Note: While the ESC is IP67 rated for splash and dust resistance, avoid prolonged submersion in water. After operating in wet conditions, ensure the ESC is thoroughly dried before storage or next use.
- Storage: Store the ESC in a cool, dry place away from direct sunlight and extreme temperatures.
8. Troubleshooting
If you encounter issues with your ESC, consider the following common troubleshooting steps:
- No Power/No Response:
- Check battery connection and ensure it's charged.
- Verify ESC power switch is ON.
- Inspect all wiring for loose connections or damage.
- Motor Not Spinning/Erratic Behavior:
- Ensure motor wires are securely connected to the ESC.
- Check motor for any obstructions or damage.
- Recalibrate the ESC's throttle range with your transmitter.
- Verify transmitter batteries are charged.
- Overheating:
- Check for proper motor gearing (too high gearing can cause overheating).
- Ensure adequate airflow around the ESC.
- Verify the cooling fan is operating correctly.
- Reduce load on the motor if consistently overheating.
- ESC Beeps Continuously:
- Refer to the full Hobbywing manual for specific beep codes, which often indicate low voltage, overheating, or sensor errors.
For more detailed troubleshooting, consult the official Hobbywing product manual or contact their support.
9. User Tips
While no specific user reviews or Q&A were provided, here are some general tips for optimizing your ESC experience:
- Battery Care: Always use LiPo batteries within their specified voltage and discharge rates. Store them safely and charge them with appropriate chargers.
- Motor Pairing: Ensure your chosen brushless motor is compatible with the ESC's specifications (KV rating, size, and current draw).
- Gearing: Experiment with different pinion and spur gear combinations to find the optimal balance between speed and temperature for your specific vehicle and driving conditions.
- Firmware Updates: If available, regularly check the Hobbywing website for firmware updates for your ESC to ensure you have the latest performance enhancements and bug fixes.
10. Warranty and Support
For specific warranty terms and conditions, please refer to the official Hobbywing website or contact the authorized seller from whom you purchased the product. Keep your proof of purchase for any warranty claims.
For technical support, product inquiries, or further assistance, please visit the official Hobbywing support channels or contact your local distributor.