Hobbywing XRotor X6 PLUS

Contents

Hobbywing XRotor X6 PLUS Motor Power System Instruction Manual

Model: XRotor X6 PLUS

1. Introduction

The Hobbywing XRotor X6 PLUS Motor Power System is an integrated propulsion solution designed for agricultural UAV drones. It combines a high-efficiency motor, an 80A Electronic Speed Controller (ESC), and a 2480 foldable propeller to deliver reliable thrust and performance for various drone applications, including spraying and fertilizing. This manual provides essential information for the proper setup, operation, and maintenance of your XRotor X6 PLUS system.

Hobbywing XRotor X6 PLUS Motor Power System

Figure 1: Hobbywing XRotor X6 PLUS Motor Power System with 6218 150KV Motor, 80A ESC, and 2480 Folding Propeller.

2. Setup and Installation

This section outlines the steps for installing the XRotor X6 PLUS system onto your agricultural drone.

2.1 Component Overview

XRotor X6 PLUS Components

Figure 2: The XRotor X6 PLUS system includes the integrated motor/ESC unit, foldable propeller, and signal wires.

2.2 Mounting the Power System

  1. Ensure the drone arm has a compatible mounting surface for the XRotor X6 PLUS unit. The system is designed for a Powertrain Arm Tube Outer Diameter of 30mm.
  2. Securely attach the motor/ESC unit to the drone arm using appropriate fasteners. Ensure the unit is oriented correctly (CW or CCW as required for each arm).
  3. Connect the motor's power cables to your drone's power distribution board (PDB) or battery connector, ensuring correct polarity.
  4. Connect the signal wires from the ESC to your flight controller. The ESC supports PWM input signal levels of 3.3V/5V.

2.3 Propeller Installation

  1. Carefully unfold the 2480 propeller blades.
  2. Align the propeller hub with the motor shaft and secure it using the provided screws. Ensure all screws are tightened to the manufacturer's specifications to prevent detachment during flight.
  3. Verify that the propeller rotates freely and is not obstructed by any part of the drone frame.

3. Operating Instructions

The XRotor X6 PLUS system is designed for efficient and stable flight in agricultural applications.

Use a 12-14S LiPo battery for optimal performance. The maximum input voltage for the ESC is 61V.

3.2 Throttle Control

The system features Dual Throttle Parallel control for precise and stable flight, even without RTK GPS. The ESC operates with a throttle signal frequency of 50-500Hz and a fixed operating pulse width of 1050-1950us.

Dual Throttle Parallel Diagram

Figure 3: Dual Throttle Parallel provides precise control for stable flight paths.

3.3 Typical Applications

The XRotor X6 PLUS is suitable for various agricultural drone tasks, including:

  • Fertilizer Spreading: The system's strong payload capacity supports efficient distribution of granular fertilizers.
  • Pesticide Spraying: Provides stable flight for even and effective pesticide application over crops.
  • High-altitude Transportation: Capable of transporting payloads in challenging terrains, as demonstrated in the video below.

Video 1: Demonstration of drone usage with Hobbywing Thrust System for agricultural tasks and high-altitude transportation.

4. Maintenance

Regular maintenance ensures the longevity and reliable performance of your XRotor X6 PLUS system.

  • Inspection: Before each flight, visually inspect the motor, ESC, and propeller for any signs of damage, wear, or loose connections.
  • Cleaning: Keep the motor and ESC free from dust, dirt, and debris. The system has an IPX6 ingress protection rating, but regular cleaning is still recommended, especially after operating in dusty or wet conditions.
  • Propeller Check: Ensure propeller blades are free from nicks, cracks, or bends. Replace damaged propellers immediately.
  • Connection Check: Verify that all electrical connections (power and signal) are secure and free from corrosion.
  • Heat Dissipation: Ensure the motor's heat sink fins are clear of obstructions to allow for efficient heat dissipation. The X6 PLUS features an upgraded active heat dissipation structure.
Motor Heat Dissipation

Figure 4: The X6 PLUS motor features an upgraded heat dissipation structure for improved thermal management.

5. Troubleshooting

This section addresses common issues you might encounter with your XRotor X6 PLUS system.

  • Motor Not Spinning:
    - Check battery connection and voltage.
    - Verify signal wire connection to the flight controller.
    - Ensure the ESC is armed correctly by the flight controller.
  • Irregular Motor Operation:
    - Inspect propeller for damage or imbalance.
    - Check for loose motor mounts or connections.
    - Verify flight controller settings for ESC calibration.
  • Overheating:
    - Ensure the motor and ESC are not covered or obstructed.
    - Check for excessive load on the motor (e.g., too heavy payload, damaged propeller).
    - Operate within recommended temperature ranges (-20~50°C).
  • Reduced Performance:
    - Check battery health and charge level.
    - Inspect propellers for damage or wear.
    - Ensure the drone's total weight is within the recommended takeoff weight range.

6. Specifications

Detailed technical specifications for the Hobbywing XRotor X6 PLUS Motor Power System.

FeatureSpecification
Product NameXRotor X6 PLUS
Max Thrust11.8 Kg/Axis (46V, Sea Level)
Thrust/Rotor3.5-5.5 Kg/Axis (46V, Sea Level)
Recommended Takeoff Weight3.5-5.5kg/Axis (for 10-30kg drone)
Total Weight (System)790g
Recommended LiPo Battery12-14S (LiPo)
Operating Temperature-20~50°C
Ingress ProtectionIPX6
Motor KV Rating150rpm/V
Motor Stator Size62*18mm
Motor SizeΦ69.4 *35.6
Motor BearingWaterproof
Powertrain Arm Tube Outer Diameter30mm
Propeller Diameter + Pitch24*8.0 inch (2480 Foldable)
Single Propeller Weight33.5g
ESC Max. Input Voltage61V
ESC Max. Input Current (Short duration)80A (Non-hermetic Ambient Temperature 60°C)
ESC Continuous Current (Non-hermetic Ambient Temperature ≤60°C)25A
ESC PWM Input Signal Level3.3V/5V
ESC Throttle Signal Frequency50-500Hz
ESC Operating Pulse Width1050-1950us (Fixed)
ESC BECNo
XRotor X6 PLUS CAD Dimensions

Figure 5: CAD dimensions of the XRotor X6 PLUS system.

7. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official Hobbywing website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.

© 2024 Hobbywing. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.