SHIMANO FD-TZ500

Contents

Shimano Tourney TZ FD-TZ500 Front Derailleur User Manual

Installation, Adjustment, and Maintenance Guide

Important Safety Information

This manual is intended primarily for use by professional bicycle mechanics. Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using this manual. If any part of the information is unclear, do not proceed with installation; contact your place of purchase or a distributor for assistance.

  • Always read all manuals included with each product.
  • Do not disassemble or modify the product other than as stated in this manual.
  • Wear approved eye protection while performing maintenance tasks.
  • Keep the crank arm turning during lever operation.
  • Periodically wash chainrings and sprockets with a neutral detergent. Lubricating the chain can extend its life.
  • Products are not guaranteed against natural wear and deterioration from normal use and aging.
  • For maximum performance, SHIMANO lubricants and maintenance products are recommended.

Safety Warnings

DANGER: Failure to follow instructions will result in death or serious injury.

WARNING: Failure to follow instructions could result in death or serious injury.

CAUTION: Failure to follow instructions could cause personal injury or physical damage to equipment and surroundings.

Product Specifications

FeatureSpecification
Brand NameSHIMANO
Model NumberFD-TZ500
TypeFront Derailleur
ComponentsDerailleurs
Gears3 Speed (compatible with 6/7 speed rear systems)
Derailleur Groupset TypeMechanical Derailleur system
Clamp Band Mount31.8mm
Top Pull CompatibilityFits 42T crankset
Down Pull CompatibilityFits 48T crankset

The Shimano Tourney TZ FD-TZ500 is available in both Top Pull and Down Pull configurations to suit different bicycle frame designs and crankset sizes.

Shimano Tourney TZ FD-TZ500 Front Derailleur, showing both Top Pull and Down Pull versions

Figure 1: Shimano Tourney TZ FD-TZ500 Front Derailleur (Top Pull and Down Pull)

Tools Required

The following tools are needed for installation, removal, adjustment, and maintenance:

  • 2.5 mm hexagon wrench
  • 3 mm hexagon wrench
  • 5 mm hexagon wrench
  • 9 mm spanner
  • Cross head screwdriver
  • Cross head screwdriver [#1]
  • TL-CT12 (Cable cutter/rounder)

Setup and Installation

1. Installing the Shift Lever (for controlling the Front Derailleur)

Install the shift lever in a position where it will not obstruct brake operation. Ensure a gap of 0.5 mm between the REVOSHIFT lever and the half grip (not required for SL-RV100 / SL-RV200 / SL-RV300 / SL-RV400).

Shift Lever ModelTightening Torque
SL-RS25 / SL-RS352.5 - 3 N·m (using 3 mm hexagon wrench)
SL-RS34 / SL-RS36 / SL-RS45 / SL-RS472 - 2.5 N·m (using 3 mm hexagon wrench)
SL-RV100 / SL-RV200 / SL-RV300 / SL-RV4001.5 - 2 N·m (using 2.5 mm hexagon wrench)
Diagram illustrating the installation of the REVOSHIFT shift lever on a handlebar, showing torque specifications for left and right-hand levers.

Figure 2: Shift Lever Installation

2. Front Derailleur Adjustment (Left-Hand Lever Adjustment)

Perform adjustments in the indicated order.

2.1. Adjusting the Low Side Position

  1. For models equipped with a Pro-Set alignment block, remove it.
  2. Shift the chain to the smallest chainring (front) and the largest sprocket (rear).
  3. Adjust the low position of the front derailleur. The gap between the inner plate and the chain should be 0 - 0.5 mm.
Diagram showing front derailleur adjustment points for low position, indicating inner plate and chain gap for top and down swing types.

Figure 3: Front Derailleur Low Position Adjustment

2.2. Connecting and Securing the Inner Cable

  • Insert the inner cable into the outer casing from the end with the marking on it. The marked end is greased to maintain cable operating efficiency.
  • When cutting the outer casing, cut the opposite end to the end with the marking. After cutting, use a TL-CT12 needle or similar tool to round the end, ensuring a uniform diameter inside the hole.
  • Attach the same outer cap to the cut end of the outer casing.
  • Route the inner cable as shown in the figure.
  • While firmly pulling the inner cable, tighten the wire mounting screw to secure the cable in place. The tightening torque is 5 - 7 N·m. This applies to FD-M310 / FD-M315 / FD-TX800 / FD-TY700 / FD-TY710 / FD-TY500 / FD-TY510 (Top Swing Type) and FD-M313 / FD-TY300 / FD-TZ500 / FD-TZ510 (Down Swing Type).
Diagram illustrating inner cable connection and routing for front derailleurs, including proper cable path and tightening screw location for top and down swing types.

Figure 4: Inner Cable Routing and Securing

2.3. Adjusting the Cable Tension

  1. After taking up the initial slack in the inner cable, re-secure it to the front derailleur.
  2. Cut off the excess length of the inner cable, then install the inner end cap.

2.4. Adjusting the High Limit

  1. Adjust the chain to the largest chainring (front) and the smallest sprocket (rear).
  2. Adjust the top position of the front derailleur. The gap between the outer plate and the chain should be 0 - 0.5 mm.

2.5. Middle Chainring Adjustment

This adjustment is not necessary for LN (friction type) shifters as they do not have a cable adjustment barrel.

  1. Set the chain on the largest sprocket (rear). At the front, move the chain from the largest chainring to the middle chainring to adjust.
  2. Adjust the middle chainring position of the chain guide. Use the cable adjustment barrel to adjust the gap between the inner plate and the chain to 0 - 0.5 mm.

2.6. Checking Gear Shifting and Fine Adjustment

After completing all adjustments, move the shift lever to check the gear shifting performance. This also applies if gear shifting becomes difficult during use.

3. SIS Adjustment (for Shifter System)

For optimal SIS (Shimano Index System) performance, follow these steps:

  1. Operate the shift lever once to move the chain from the smallest sprocket to the 2nd sprocket.
  2. While operating the lever just enough to close the lever play, turn the crank arm. The best setting is when the shift lever is operated just enough to close the lever play and the chain touches the 3rd sprocket counting from the smallest sprocket and makes noise.
  3. Return the lever to its original position (where the chain is on the 2nd sprocket and the lever has been released), then turn the crank arm. If the chain is touching the 3rd sprocket and making noise, turn the adjustment barrel clockwise slightly to tighten it just enough until the noise stops.
  4. Operate the lever to change gears, and check that no noise occurs in any of the gear positions.
  5. For the best SIS performance, periodically lubricate all power-transmission parts.

Maintenance

1. Replacing the Inner Cable (for SL-RS series shifters)

  1. Operate the shifter to shift the chain to the smallest sprocket (at the rear) or the smallest chainring (at the front).
  2. Remove the cover.
  3. Follow the procedures to replace the inner cable.
  4. Install the cover. Tightening torque: 0.1 - 0.25 N·m (for SL-RS47/SL-RS45/SL-RS36) or 0.1 - 0.2 N·m (for SL-RS34).

2. Replacing the Inner Cable (for SL-RV100/RV200/RV300 shifters)

  1. Turn over the rubber grip from the area with the triangle mark to ensure the inner head of the inner cable can be seen.
  2. Pull out the inner head and remove the inner cable using a sharp tool.
  3. Insert a new inner cable into the hole.
  4. Pass the inner cable through the bracket and out from the stopper area of the outer casing.

3. Replacing the Inner Cable (for SL-RV400 shifters)

  1. Operate the shifter to shift the chain to the smallest sprocket (at the rear) or the smallest chainring (at the front).
  2. Remove the cover.
  3. Pull out the inner head and remove the inner cable using a sharp tool.
  4. Insert a new inner cable into the hole.
  5. Pass the inner cable through the bracket.
  6. Install the cover: (1) Install the cover to the bracket from the screw hole part. (2) Install the cover along the bracket, then insert the hook into the hole. (3) Tighten the screw (0.1 - 0.25 N·m). Check the hook to ensure the cover is completely installed.

Troubleshooting

SituationAdjustment Method
Chain falls to the crank sideTurn the high limit screw clockwise.
Shifting difficult from middle chainring to largest chainringTighten the cable. If this does not improve, turn the high limit screw counterclockwise.
Shifting difficult from middle chainring to smallest chainringTurn the low limit screw counterclockwise.
Interference between chain and front derailleur inner plate when chain is on largest chainringTurn the high limit screw clockwise.
Interference between chain and front derailleur outer plate when chain is on largest chainringTighten the cable. If this does not improve, turn the high limit screw counterclockwise.
Middle chainring is skipped when shifting from largest chainringTighten the cable.
Interference between chain and front derailleur inner plate when chain is on largest sprocket at rear and middle chainringLoosen the cable.
Shifting difficult from largest chainring to middle chainringLoosen the cable.
Chain falls to the bottom bracket sideTurn the low limit screw clockwise.

User Tips

  • Cable Pull Direction: The Shimano Tourney TZ FD-TZ500 Front Derailleur is available in both Top Pull and Down Pull versions. Ensure you select the correct type for your bicycle's frame and crankset. Top Pull is typically for 42T cranksets, and Down Pull for 48T cranksets.
  • Professional Installation: While this guide provides detailed instructions, professional installation by a qualified bicycle mechanic is highly recommended to ensure optimal performance and safety.

Warranty and Support

For warranty information, technical support, or to find a distributor, please contact the appropriate Shimano office:

  • SHIMANO NORTH AMERICA BICYCLE, INC.
    One Holland, Irvine, California 92618, U.S.A.
  • SHIMANO EUROPE B.V.
    High Tech Campus 92, 5656 AG Eindhoven, The Netherlands
  • SHIMANO INC.
    3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan

Please note that specifications are subject to change for improvement without notice.

A detailed user manual (PDF) for related components, such as the REVOSHIFT Shifter, which controls this derailleur, is available for download. You can find relevant documentation on the official Shimano website: https://si.shimano.com. Additionally, a specific user manual PDF for this item is referenced as: User manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.