1. Introduction
The Anytone ARES II is a versatile 10-meter radio transceiver designed for reliable communication. It supports multiple modes including AM, FM, USB, LSB, and PA, with adjustable power output up to 40W. This manual provides essential information for setting up, operating, and maintaining your ARES II radio.
Figure 1: Anytone ARES II SSB 10 Meter Radio Transceiver.
2. Package Contents
Please check the box for the following items:
Figure 2: Standard Accessories.
- 1 × ARES II 10 Meter Radio
- 1 × Microphone
- 1 × Mounting Bracket
- 1 × Microphone Hanger
- 2 × Adhesive Case Protectors
- 1 × DC Power Cable
- 1 × Screws for bracket
- 1 × Pads for bracket
- 1 × Adjusting screws
- 1 × Spare Fuses 10A, 250V
- 1 × Self-tapping Screws
- 1 × Pads
- 1 × Instruction Manual (this document)
3. Product Overview
The Anytone ARES II features a user-friendly front panel with various controls and indicators, and a rear panel for essential connections.
Figure 3: Front Panel Controls.
- S-Meter
- NB/ANL function on/off
- NRC function on/off/set
- Control Monitor/10K on/off
- ECHO function on/off/set
- H Band, L Band or WX (FM RX) Band groups
- TX/RX indicator
- Channel Display: CH and Scrolling Frequency Display
- Microphone connector
- Power on/off and Volume level control
- Squelch level control
- FIN Frequency control: +/-500Hz and +/-5kHz
- RF Gain control
- Mode switch: PA/FM/AM/USB/LSB
- Band switch: A/B/C/D/E/F
- Microphone Gain control
- RF Power level control
- Channel /Frequency control
Figure 4: Rear Panel Connections and Microphone.
- External SP Jack
- PC programming port
- External PA Jack
- Antenna Jack
- Power Supply Jack
4. Setup
Follow these steps to set up your Anytone ARES II radio:
-
Power Connection:
Connect the supplied DC Power Cable to the Power Supply Jack (23) on the rear panel of the radio. Ensure the other end is connected to a compatible 13.8V DC power source. Observe correct polarity (red to positive, black to negative).
Video 1: Unboxing and Power Connection Demonstration.
-
Microphone Connection:
Plug the microphone connector into the Microphone Connector (9) on the front panel. Secure it by twisting the collar.
-
Antenna Connection:
Connect your 10-meter antenna to the Antenna Jack (22) on the rear panel. Ensure a proper SWR (Standing Wave Ratio) for optimal performance and to prevent damage to the radio.
-
Mounting:
Use the provided mounting bracket, screws, and adjusting screws to securely install the radio in your desired location, such as a vehicle. The adhesive case protectors can be used to prevent scratches.
-
PC Programming (Optional):
If you intend to program channels via PC, connect the PC programming cable to the PC programming port (20) and to your computer. Refer to the software manual for detailed programming instructions.
5. Operating Instructions
-
Power On/Off and Volume:
Turn the Power on/off and Volume level control (10) clockwise to power on the radio and adjust the audio volume.
-
Squelch Adjustment:
Adjust the Squelch level control (11) to eliminate background noise when no signal is present. Turn it clockwise until the noise disappears.
Figure 5: Squelch Level Control.
-
Channel/Frequency Selection:
Use the Channel/Frequency control (18) to select your desired operating channel or frequency. The selected channel will be shown on the Channel Display (8).
-
Mode Selection:
Rotate the Mode switch (14) to select between PA, FM, AM, USB, or LSB modes.
Figure 6: AM/FM/SSB Modulation.
-
NB/ANL Function:
The Noise Blanker (NB) and Automatic Noise Limiter (ANL) functions (2) help reduce static and interference. Toggle the switch to activate or deactivate these features. These are particularly useful for reducing ignition noise, power line interference, and inverter noise.
Figure 7: NB/ANL Function.
-
VOX Function:
The VOX function (Voice Operated Transmit) allows for hands-free transmission. When activated, the radio will transmit when it detects your voice. Adjust the VOX sensitivity as needed.
Figure 8: VOX Function.
-
Echo Function:
Activate the ECHO function (5) for an echo effect on your transmitted audio.
-
Weather Channel:
The radio includes Weather Channels with ALERT functionality and an FM receiver for 140-170MHz. Select the WX band group (6) to access these channels.
Figure 9: Weather Channels.
-
Scan Function:
The SCAN function allows the radio to automatically scan through channels. Refer to the full instruction manual for specific steps to activate and configure scanning.
Figure 10: Scan Function.
-
RF Gain, Microphone Gain, RF Power Adjustment:
Adjust RF Gain (13) to control receiver sensitivity, Microphone Gain (16) for microphone input level, and RF Power (17) for transmit power output.
Figure 11: Power Output.
-
SWR Readout and Protection:
The radio features SWR readout and high SWR protection to safeguard the unit from antenna mismatches. Always ensure your antenna is properly tuned.
6. Maintenance
- Keep the radio clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the radio to extreme temperatures, humidity, or direct sunlight.
- Ensure all connections are secure and free from corrosion.
- Do not attempt to open or repair the radio yourself, as this will void the warranty and may cause damage.
7. Troubleshooting
- No Power: Check the DC power cable connection and ensure the power source is providing 13.8V. Verify the fuse is intact.
- No Transmission/Reception: Ensure the antenna is properly connected and tuned. Check the mode selection.
- Poor Audio Quality: Adjust the Squelch, RF Gain, and Microphone Gain controls. Check microphone connection.
- Interference/Noise: Utilize the NB/ANL function to reduce static.
8. Specifications
| Category | Specification |
|---|---|
| GENERAL | |
| Frequency Range | 28.000-29.695MHz (PC Programmable) |
| Frequency Band | L/H Band: A/B/C/D/E/F.WX/VHF RX:140-170MHz |
| Channels | 480 channels (40 programmable per band) |
| Frequency Control | Phase-locked-loop Synthesizer |
| Frequency Tolerance | ±5.0ppm |
| Temperature Range | -20°C to +50°C |
| Microphone | With push-to-talk [UP]/[DN] buttons and coiled cord |
| Input Voltage | 13.8V |
| Dimensions (in mm) | 287(L)*200(W)*61(H) |
| Weight | 1.5kg |
| Antenna Connector | UHF,SO239 |
| TRANSMITTER | |
| Power Output | AM:1-12W(adjustable) FM:1-40W(adjustable) USD/LSB:1-35W(adjustable) |
| Current Drain | 8A (with modulation) |
| Modulation | FM/AM/SSB |
| Inter-modulation Distortion | SSB:3rd order, more than -25dB; 5th order, more than -35dB |
| SSB Carrier Suppression | 55dB |
| Unwanted Sideband | 50dB |
| Frequency Response | AM/FM:450 TO 2500Hz |
| Output Impedance | 50ohms, unbalanced |
| RECEIVER | |
| Sensitivity | AM:1.0uV FOR 10dB(S+N)/N at greater than 1/2watt of audio output. FM:1.0uV FOR 20dB(S+N)/N at greater than 1/2watt of audio output. SSB:0.25uV for 10dB(S+N)/N at greater than 1/2watt of audio output |
| Selectivity | AM/FM:6dB @3kHz, 50dB@9kHz SSB:6dB@2.1kHz, 60dB@3.3kHz |
| Adjacent-Channel Selectivity | 60dB AM/FM & 70dB SSB |
| Image Rejection | More than 65dB |
| IF Frequency | AM/FM:10.695MHz 1stIF, 455kHz 2ndIF SSB:10.695MHz |
| RF Gain Control | 45dB adjustable |
| Automatic Gain Control (AGC) | Less than 10dB change in audio output for inputs from 10uV to 100,000uV |
| Squelch | Adjustable; threshold less than 0.5uV. Automatic squelch control (only AM/FM) 0.5uV |
| ANL | Switchable |
| Noise Blanker | RF Type, effective on AM/FM and SSB |
| Audio Output Power | 3watts into 8 ohms |
| Frequency Response | AM/FM:300 to 2800Hz |
| Built-in Speaker | 8ohms, round |
| External Speaker (Not Supplied) | 8 ohms, disables internal speaker when connected |
Note: Specifications are subject to change without notice due to advancements in technology.
9. User Tips
- For optimal performance, ensure your antenna is properly calibrated. One user noted excellent performance with a high-grade wattmeter and dummy load, confirming the radio delivers 40W in FM mode.
- The radio is PC programmable, allowing for customization of channels and settings. A programming cable is included.
- The NB/ANL functions are highly effective in reducing static from ignition noise, power lines, and inverters.
- The radio supports the 10-meter band (28.000-29.695MHz) and can also cover the 11-meter (27MHz CB) band if programmed accordingly.
- Transmission power is adjustable, allowing you to fine-tune output as needed.
10. Warranty and Support
For warranty information and technical support, please refer to the official Anytone website or contact your authorized dealer. Keep your purchase receipt as proof of purchase.