1. Introduction
This manual provides detailed instructions for the proper setup, operation, and maintenance of your wishiot H-11 Micro Digital Servo Motor. Designed for various remote control applications, this high-performance servo offers precise control and high torque in a compact form factor. Please read this manual thoroughly before use to ensure optimal performance and longevity of your product.

Figure 1: wishiot H-11 Micro Digital Servo Motor and included accessories.
2. Product Overview
The wishiot H-11 is a micro digital servo motor featuring a full metal gear train and a coreless high-speed motor, providing excellent durability and quick response. It is programmable for 180-degree or 270-degree controllable angle rotation, and also supports 360-degree continuous rotation. Its compact size makes it suitable for a wide range of RC models.
Video 1: Product demonstration and features of the wishiot H-11 servo motor.

Figure 2: The H-11 servo motor is suitable for various RC applications.
3. Specifications
The following table details the mechanical and electrical specifications of the wishiot H-11 Digital Servo Motor:

Figure 3: Detailed specifications of the H-11 servo motor.
General Specifications:
- Product Name: 11KG Digital servo motor
- Storage Temperature Range: -30°C to 80°C
- Operating Temperature Range: -25°C to 70°C
- Humidity Range: 65% ± 10%
- Splash Water Resistance: IP65
- Certifications: CE, RoHS
Mechanical Specifications:
- Size: 23.0 x 26.3 x 12mm
- Weight: 22g ± 5%
- Gear Type: 5 Metal
- Limit Angle: 360°
- Bearing: 2BB
- Horn Gear Spline: 25T, Diameter: 5.0mm
- Horn Type: Plastic, POM
- Case Material: Aluminum alloy
- Connector Wire Length: 250mm ± 5mm
- Motor Type: Coreless high speed motor

Figure 4: Dimensional drawing of the H-11 servo motor.
Electrical Specifications:
- Operating Voltage: 4.8V, 6.0V, 7.4V, 8.4V
- Idle Current: <40mA
- No-load Speed:
- 0.11 sec/60° (at 4.8V)
- 0.09 sec/60° (at 6.0V)
- 0.07 sec/60° (at 7.4V)
- 0.06 sec/60° (at 8.4V)
- Running Current: 160mA (4.8V), 180mA (6.0V), 220mA (7.4V), 250mA (8.4V)
- Peak Stall Torque:
- 6.5 kg.cm (at 4.8V)
- 8.5 kg.cm (at 6.0V)
- 11.5 kg.cm (at 7.4V)
- 13.5 kg.cm (at 8.4V)
- Stall Current: 1600mA ± 10% (4.8V), 2000mA ± 10% (6.0V), 2200mA ± 10% (7.4V), 2500mA ± 10% (8.4V)
Control Specifications:
- Command Signal: Pulse Width Modification (PWM)
- Amplifier Type: Digital controller
- Pulse Width Range: 500µsec to 2500µsec
- Neutral Position: 1500µsec
- Running Degree: 180° ± 3° (when 500µsec to 2500µsec)
- Dead Band Width: 3 µsec
- Rotating Direction: Counterclockwise (when 1000µsec to 2000µsec)
- Signal Voltage: 3.0V to 5.0V
- Signal Period: 20ms
4. Setup
Follow these steps to properly set up your wishiot H-11 servo motor:
- Mounting: Securely mount the servo motor to your RC model using the provided screws and mounting hardware. Ensure it is firmly attached to prevent movement during operation.
- Horn Attachment: Select the appropriate servo horn for your application from the included accessories. Attach it to the servo's output shaft.
- Electrical Connection: Connect the servo's 3-wire cable to your receiver or servo controller. The standard color coding is typically:
- Orange/Yellow: Signal (PWM input)
- Red: Positive Power (VCC)
- Brown/Black: Ground (GND)
Ensure the operating voltage supplied to the servo is within the specified range of 4.8V to 8.4V. The signal voltage should be between 3.0V and 5.0V.
- Calibration (if applicable): If your controller or receiver requires calibration, follow its specific instructions to set the servo's neutral position and end points.

Figure 5: Illustration of controllable rotation angles and pulse width input.
5. Operating Instructions
The wishiot H-11 servo motor operates based on Pulse Width Modulation (PWM) signals. The pulse width determines the servo's position or rotation speed.
- Controllable Angle Modes (180°/270°): In these modes, the servo will move to a specific angle corresponding to the input pulse width. A pulse width of 1500µsec typically corresponds to the neutral (center) position. Pulse widths below 1500µsec move the servo in one direction, and above 1500µsec move it in the opposite direction, within its specified angular range.
- Continuous Rotation Mode (360°): When configured for 360-degree continuous rotation, the servo will rotate continuously. In this mode, the pulse width controls the speed and direction of rotation, rather than a specific angle. For example, 1500µsec might be stop, while values above or below cause rotation in different directions and speeds. Please note: The 360-degree mode is for continuous rotation and does not offer controllable angular positioning.
6. Maintenance
To ensure the longevity and reliable performance of your servo motor, follow these maintenance guidelines:
- Keep Clean: Regularly clean the exterior of the servo to prevent dust and debris from accumulating, especially around moving parts.
- Avoid Overload: Do not exceed the specified peak stall torque. Excessive force can damage the internal gears and motor.
- Operating Environment: Operate the servo within its specified temperature and humidity ranges. While it has IP65 splash water resistance, avoid full submersion or exposure to harsh chemicals.
- Check Connections: Periodically inspect all electrical connections for looseness or corrosion.
- Gear Inspection: Although the servo features durable metal gears, occasional inspection for wear or damage is recommended, especially after heavy use.

Figure 6: The H-11 servo motor features IP65 splash water resistance.

Figure 7: The servo features robust metal gears for durability.
7. Troubleshooting
If you encounter issues with your servo motor, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Servo not responding | Incorrect wiring, insufficient power, faulty signal, damaged servo. | Check all connections (signal, VCC, GND). Ensure power supply voltage is within 4.8V-8.4V. Verify signal input from controller. Test with a known working servo or controller. |
| Erratic movement or twitching | Noisy power supply, signal interference, loose connections, dead band width issues. | Ensure a stable power supply. Check for sources of electrical interference. Secure all connections. Verify dead band width setting if programmable. |
| Servo not reaching full range of motion | Incorrect pulse width range, mechanical obstruction, power supply issues. | Check the pulse width range settings on your controller (should be 500-2500µsec for 180°/270°). Ensure no physical obstructions. Verify adequate power supply. |
| Servo overheating | Overload, continuous stall, high ambient temperature. | Reduce load on the servo. Avoid continuous stalling. Ensure proper ventilation and operate within specified temperature range. |
8. User Tips
- Power Supply: Always ensure your power supply can deliver sufficient current for the servo, especially under load. Digital servos can draw significant current during peak torque.
- Signal Compatibility: While standard PWM is used, always verify compatibility with your specific receiver or flight controller.
- Initial Testing: Before full deployment in your model, perform bench testing to confirm the servo's functionality and range of motion.
9. Warranty & Support
For any technical assistance, warranty claims, or support inquiries regarding your wishiot H-11 Micro Digital Servo Motor, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase for warranty purposes.