1. Introduction
This manual provides detailed instructions for assembling and operating your Colorful DIY Digital Clock Kit. This kit is designed for enthusiasts and learners interested in electronics and soldering, offering a hands-on experience to build a functional digital clock with various features.
The finished clock displays time, date, day of the week, and temperature, and includes alarm functions and intelligent photosensitivity for automatic brightness adjustment.
2. Safety Information
- Always work in a well-ventilated area when soldering.
- Use appropriate safety gear, such as safety glasses, to protect your eyes from solder splashes.
- Ensure your soldering iron is properly grounded and handle it with care to prevent burns.
- Keep electronic components away from children and pets.
- Verify component polarity and placement before soldering to avoid damage.
- Only use the specified USB power supply (5V DC) for the clock.
3. Package Contents
Please check the contents of your kit against the list below. If any components are missing or damaged, please contact customer support.

Image: Overview of the DIY Digital Clock Kit components.
- Printed Circuit Board (PCB)
- Digital Tube Display Module
- USB Power Cable (Type A to DC 5.5mm jack)
- Resistors (various values, including 10kΩ)
- Ceramic Capacitors
- Integrated Circuits (ICs): STC8G1K17/15W413AS, DS1302
- IC Sockets
- Crystal Oscillator (32.768kHz)
- Push Buttons (SET, UP)
- Buzzer
- Photoresistor
- Thermistor
- Transistor
- DC Power Socket
- CR1220 Battery Holder
- CR1220 Button Cell Battery
- Acrylic Case (top, bottom, side panels)
- Screws
4. Assembly Instructions
Follow these steps carefully to assemble your digital clock kit. It is recommended to watch the video tutorial linked via the QR code on the included paper manual for visual guidance.
4.1. Soldering Components to PCB
- Install 10kΩ Resistors: Solder the four 10kΩ resistors onto the PCB. Resistors do not have polarity, so orientation does not matter.

Image: Steps 1-6 of PCB component installation.
- Install Crystal Oscillator: Solder the crystal oscillator onto the PCB. It does not have polarity.
- Install Ceramic Capacitors: Solder the ceramic capacitors onto the PCB. These do not have polarity.
- Install Battery Holder: Solder the CR1220 battery holder onto the PCB.
- Install IC Holders: Solder the IC holders onto the PCB. Ensure the notch on the IC holder aligns with the notch marking on the PCB.
- Install Buzzer: Solder the buzzer onto the PCB. Align the positive (+) side of the buzzer with the corresponding marking on the circuit board.
- Install Transistor: Solder the transistor onto the PCB. Align the flat or semicircular side of the transistor with the corresponding marking on the circuit board.

Image: Steps 7-12 of PCB component installation.
- Install Switch and DC Socket: Solder the push buttons (SET, UP) and the DC power socket onto the PCB.
- Install Photoresistor and Thermistor: Solder the photoresistor and thermistor onto the PCB. These components do not have polarity. Leave a distance of approximately 1cm from the circuit board during installation.
- Weld Header on Digital Tube: Solder the pin header onto the digital tube display module.
- Install Digital Tube: Carefully check for any welding errors on the PCB. Once confirmed, insert the digital tube display module into its corresponding socket on the PCB.
4.2. Final Assembly
- Install ICs into Sockets: Carefully insert the STC8G1K17/15W413AS and DS1302 ICs into their respective sockets. Ensure the notch on each IC aligns with the notch on the socket and the PCB.

Image: Steps 13-16 of final assembly.
- Install CR1220 Battery: Insert the CR1220 button cell battery into its holder. The shrapnel part of the holder is typically positive (+), and the circuit board side is negative (-).
- Adjust Photoresistor and Thermistor: Adjust the position of the photoresistor and thermistor as needed for optimal performance and aesthetic.
- Assemble Acrylic Case: Carefully place the assembled PCB into the acrylic case. Secure the case panels using the provided screws.
5. Circuit Diagram
For advanced users and troubleshooting, the circuit diagram provides a detailed overview of the electronic connections and components.

Image: Circuit Diagram of the Digital Clock Kit.
6. Operating Instructions
Once assembled and powered via the USB cable, your digital clock is ready to use. Use the 'SET' and 'UP' buttons to navigate and adjust settings.
6.1. Basic Functions
- Time Display: The clock will automatically display the current time upon power-up.
- 12/24 Hours Switching: Toggle between 12-hour (with PM indicator) and 24-hour formats.
- Temperature Display: View the current ambient temperature.
- Date Display: View the current date.
- Week Display: View the current day of the week.
- Intelligent Photosensitivity: The clock automatically adjusts display brightness based on ambient light conditions.
- Power Off Memory: Settings are retained even when power is disconnected, thanks to the CR1220 backup battery.
6.2. Function Setting
- Enter Setting Mode: Long press the 'SET' button to enter the setting mode.
- Change Parameters: While in setting mode, press the 'UP' button to cycle through and change parameters (e.g., time, date, alarm settings).
- Alarm Clocks: The clock supports up to three independent alarm settings.
- Workday Alarm Clock: Configure alarms to activate only on specific weekdays.
- Music: Choose from three sets of alarm music.
- Hourly Reminder: You can set an hourly chime. By default, the hourly reminder is active from 7:00 AM to 9:00 PM (21:00) and is turned off at night.
7. Maintenance
- Keep the clock clean and free from dust. Use a soft, dry cloth for cleaning.
- Avoid exposing the clock to moisture or extreme temperatures.
- Handle the assembled clock with care to prevent damage to the acrylic case or internal components.
- If the timekeeping becomes inaccurate after a power outage, the CR1220 battery may need replacement.
8. Troubleshooting
- No Display/Power: Ensure the USB cable is securely connected to both the clock and a 5V power source. Check for any visible soldering errors or shorts on the PCB.
- Incorrect Time/Date: Enter the setting mode (long press SET) and adjust the time and date. If settings are not saved after power loss, check if the CR1220 battery is correctly installed and has sufficient charge.
- Instructions in Chinese: The included paper manual may be in Chinese. Look for a QR code on the manual which links to an English-subtitled video tutorial for assembly and setup.
- Component Issues: If you suspect a component is faulty (e.g., incorrect capacitor values as noted by some users), verify its specifications before soldering.
- Soldering Problems: Cold joints (dull, lumpy solder) or solder bridges (solder connecting two points that shouldn't be connected) can cause malfunctions. Re-solder any suspicious connections.
9. Specifications
| Feature | Specification |
|---|---|
| Main Control Chip | STC8G1K17 or 15W413AS |
| Real-Time Clock (RTC) Chip | DS1302 |
| Material | Transparent Acrylic (case) |
| Power Supply | USB Powered (5V DC) |
| Backup Battery | CR1220 (for power-off memory) |
| Dimensions (L x W x H) | 11.5 cm x 4 cm x 3.2 cm |
| Weight | 0.103 kg |
| Functions | Time, Date, Week, Temperature Display, 12/24H Switching, 3 Alarm Clocks, Workday Alarm, 3 Music Options, Intelligent Photosensitivity, Hourly Reminder, Power Off Memory |

Image: Product size and key feature labels.
10. User Tips
- Video Instructions: If the printed instructions are not in your preferred language, look for a QR code on the manual. This often links to an English-subtitled video tutorial which can be very helpful for assembly.
- Focus on Time: If you prefer a simpler display, you can configure the clock to show only the time, rather than cycling through date or temperature.
- Component Verification: Before soldering, it's good practice to verify the values of components like capacitors, as some users have reported slight discrepancies.
- Included Accessories: The kit typically includes a CR1220 battery and a USB Type-A to DC 5.5mm jack cable. The clear acrylic case comes with pre-cutouts for easy assembly.
11. Video Tutorial
Watch this official product video for a visual guide to the kit components and a general overview.
Video: Overview of the DIY Digital Clock Kit components.
12. Warranty and Support
For any issues, questions, or support regarding your Colorful DIY Digital Clock Kit, please contact the seller or manufacturer directly. Keep your purchase records for reference.