1. Introduction
Thank you for choosing the PowMr PWM Solar Charge Controller. This device is designed to manage the power flow from your solar panel to your battery, preventing overcharging and extending battery life. It is compatible with 12V and 24V lead-acid battery systems and features dual USB outputs for charging external devices. This manual provides essential information for the safe installation, operation, and maintenance of your solar charge controller.

2. Safety Information
- WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
- Ensure your battery has sufficient voltage for the controller to recognize the battery type before the first installation.
- Battery cables should be as short as possible to minimize power loss.
- This regulator is only suitable for lead-acid batteries (OPEN, AGM, GEL). It is not suited for nickel-metal hydride, lithium-ion, or other battery types.
- The charge regulator is exclusively designed for regulating solar modules. Never connect another charging source to the charge regulator.
- Install the controller in a well-ventilated area to prevent overheating.
3. Product Overview
3.1 Key Features
- PWM Charging: Utilizes 3-stage PWM charging (Bulk, Boost, Float) to efficiently charge batteries and prevent overcharging or over-discharging, thereby extending battery life.
- System Compatibility: Automatically adapts to 12V/24V battery systems.
- PV Voltage Range: Supports PV input up to 23V for 12V systems and 46V for 24V systems.
- Dual USB Output: Provides two USB ports with a maximum output of 5V/2.5A for charging mobile devices.
- Multiple Safety Protections: Includes short circuit protection, over current protection, open circuit protection, self-recovery, temperature protection, and high-temperature protection.
- Compact Design: Small and lightweight for easy installation.



3.2 Components

- LCD Display: Shows various system parameters and settings.
- USB Port: Dual 5V/2.5A output for charging devices.
- Function Keys: Used for navigating the interface and adjusting settings.
- Mounting Holes: Four Φ5mm holes for secure installation.
- PV Input Port: Connects to solar panels.
- Load Port: Connects to DC loads.
- Battery Port: Connects to the battery bank.
4. Setup Instructions
Follow these steps for proper installation and connection of your solar charge controller:
- Mounting: Install the controller in a well-ventilated area, away from direct sunlight, high temperatures, and water. Ensure there is adequate space around the controller for heat dissipation.
- Battery Connection: Connect the battery to the controller's battery terminals first. Ensure correct polarity (+ to + and - to -). The controller will automatically detect the battery voltage (12V or 24V). Make sure the battery has enough voltage for the controller to recognize its type.
- Solar Panel Connection: Connect the solar panel to the controller's PV input terminals. Ensure correct polarity. The controller is designed to regulate solar modules only; do not connect other power sources.
- Load Connection: Connect your DC loads to the controller's load terminals. Ensure correct polarity.

5. Operating Instructions
5.1 LCD Display and Navigation
The LCD display shows various system parameters. Use the function keys to navigate and adjust settings.
- Short Press Menu Key: Cycle through the interface and parameters.
- Long Press Menu Key (for 3 seconds): Enter the settings manually. The displayed number will flash, allowing you to adjust the corresponding setting. After completing the adjustment, the system will automatically save the memory value and exit the setup menu.

5.2 Charging Stages
The controller employs a 3-stage PWM charging algorithm:
- Bulk Charge: The battery is charged at its maximum current until its voltage rises to the Boost voltage.
- Boost Charge: The battery is charged at a constant voltage, and the current gradually decreases.
- Float Charge: Once the battery is fully charged, the controller reduces the voltage to a lower level to maintain the battery at full charge and compensate for self-discharge.
6. Maintenance
To ensure optimal performance and longevity of your solar charge controller, consider the following maintenance tips:
- Keep Clean: Regularly clean the controller's exterior to prevent dust and debris buildup, which can affect heat dissipation.
- Check Connections: Periodically inspect all wiring connections to ensure they are tight and free from corrosion. Loose connections can lead to power loss or system malfunction.
- Ventilation: Ensure the installation area remains well-ventilated to prevent the controller from overheating.
- Battery Health: Monitor your battery's health and voltage regularly. Ensure it is within the recommended operating parameters for lead-acid batteries.
7. Troubleshooting
The PowMr PWM Solar Charge Controller is designed with multiple safety protections to prevent common issues. If you encounter problems, consider the following:
- No Display/No Power: Check battery connections and ensure the battery has sufficient voltage.
- No Charging: Verify solar panel connections and ensure there is adequate sunlight. Check for open circuit conditions in the solar panel wiring.
- Load Not Working: Check load connections and ensure the load is not exceeding the controller's rated discharge current. Verify that the battery voltage is above the Low Voltage Disconnection (LVD) threshold.
- Overheating: Ensure the controller is installed in a well-ventilated area. Reduce load if necessary. The controller has built-in temperature protection.
- Short Circuit/Over Current: The controller features short circuit and over current protection with self-recovery. Disconnect the faulty component, resolve the issue, and the controller should resume normal operation.
8. Specifications

| Parameter | ZBL-10A | ZBL-20A | ZBL-30A |
|---|---|---|---|
| Battery Voltage | 12V/24V auto | ||
| Charge Current | 10A | 20A | 30A |
| Discharge Current | 10A | ||
| Max Solar Input | 12V battery: highest 23V; 24V battery: highest 46V | ||
| Equalization | 14.4V | ||
| Float Charge | 13.7V (default, adjustable) | ||
| Discharge Stop | 10.7V (default, adjustable) | ||
| Discharge Reconnect | 12.6V (default, adjustable) | ||
| Charge Reconnect | 13V | ||
| Voltage of Open Light | Solar panel 8V (Light lights delay) | ||
| Voltage of Close Light | Solar panel 8V (Light off delay) | ||
| USB Output | 2 way USB output, 5V/2.5A (MAX) | ||
| Self-Consume | <10mA | ||
| Dimensions (approx.) | 11.2cm (W) x 12.5cm (H) x 3.4cm (D) / 4.4in (W) x 4.92in (H) x 1.3in (D) | ||
| Weight (approx.) | 0.4 lb | ||
| Certifications | CE, FCC, RoHS | ||
| Is Smart Device | Yes | ||
| Application | Thermal Controller | ||
9. User Tips
- For optimal performance, ensure your solar panels are clean and free from obstructions.
- Always connect the battery first and disconnect it last when working with the solar charge controller.
- Regularly check the LCD display for system status and any error indicators.
10. Warranty and Support
The PowMr PWM Solar Charge Controller comes with a 12 Months Warranty from the date of purchase. This warranty covers manufacturing defects and malfunctions under normal use.
For technical support, warranty claims, or any questions regarding your product, please contact your retailer or the manufacturer's customer service. Please have your product model and purchase details ready when contacting support.