RADIOMASTER ER8

Contents

Radiomaster ER8 8CH 2.4Ghz PWM CRSF ExpressLRS Receiver

Instruction Manual

Introduction

Thank you for choosing the Radiomaster ER8 ExpressLRS receiver. The ER8 is an 8-channel PWM CRSF ExpressLRS receiver designed specifically for fixed-wing aircraft. It is built upon the revolutionary ExpressLRS system, offering high performance, exceptional reliability, flexible configuration, rapid response times, and an ultra-long range for an enhanced hobby experience.

The ER8 receiver can drive up to 8 servos and features built-in receiver voltage telemetry, as well as external flight battery voltage telemetry with automatic detection of the voltage input. A 4-wire CRSF interface is included for future expansion with optional telemetry sensors. The receiver is equipped with dual 200mm high-sensitivity antennas and supports telemetry power up to 100mW. Its robust shell is constructed using a one-piece molding process, ensuring high structural strength.

Key Features

  • Based on the Revolutionary ExpressLRS System
  • High performance, high reliability, flexible configuration, fast response speed, and ultra-long range
  • Supports 8 PWM Channels
  • Optimized ground-up PCB design for modern servos
  • Automatic voltage telemetry for external battery voltage or built-in receiver voltage
  • Supports Wi-Fi updates and WEBUI configuration
  • High quality 2.54 mm gold-plated connectors for strong corrosion resistance
  • Standard 20 cm High Sensitivity Antenna
  • Reserve 4-pin CRSF input port for future optional telemetry sensors
  • Shell adopts one-piece molding process with high structural strength
  • Designed for fixed-wing aircraft and more
Infographic highlighting ER8 receiver features: High Performance, Reliability, Fast Response, Flexible Configuration, Ultra-Long Range, Up to 100mW Telemetry Power, 8CH PWM, 2.4 GHz, CRSF Sensor Input, 200mm High Sensitivity Antenna, EXT-V Battery Telemetry.

Infographic highlighting key features of the Radiomaster ER8 receiver.

Specifications

AttributeValue
ItemER8 2.4GHz ELRS PWM Receiver
Power SupplyDC 4.5 - 8.4V
Antenna Type20cm high sensitivity dual antenna
Wireless ProtocolExpressLRS 3.2 (pre-installed)
Output Channels8CH PWM
Telemetry PowerMaximum 100mW (LUA Adjustable)
Battery Voltage Detection RangeDC 4.0 - 35V
Bus InterfaceCRSF
Weight16.5 grams
Size43mm * 30mm * 15mm
Firmware Device CategoryRadiomaster 2.4Ghz
Firmware DeviceRadioMaster ER8 2400 PWM RX
Radiomaster ER8 receiver with dimensions: 43mm length, 30mm width, 15mm height.

Dimensions of the ER8 receiver.

Radiomaster ER8 receiver showing the 200mm length of its dual antennas.

ER8 receiver with 200mm high-sensitivity antennas.

Package Contents

  • 1 * ER8 2.4GHz ELRS PWM Receiver
  • 1 * Voltage telemetry wire (Type-B)
  • 1 * CRSF wire
  • 1 * ELRS-RX-SBUS wire
  • 1 * User Card
Contents of the Radiomaster ER8 package, including the receiver and various connection wires.

Included items in the ER8 receiver package.

Setup and Binding

Traditional Binding Method

  1. When you first power on your receiver, the LED will double blink, indicating that the receiver is in bind mode. If it is not, press and hold the BOOT button for 10 seconds to reset the receiver.
  2. Open the ExpressLRS LUA script on your remote controller, select [BIND], and confirm.
  3. A successful bind is indicated by the receiver's LED light becoming solid.

Binding with Passphrase Method

  1. Open the ExpressLRS LUA script on your remote controller and navigate to the Wi-Fi Connectivity page. Enable the Wi-Fi option and connect to your radio's Wi-Fi (default network name: ExpressLRS TX, default password: expresslrs) using a mobile phone, tablet, or PC. Open the WebUI (default URL: http://10.0.0.1/) and enter a unique bind passphrase. Save and reboot.
  2. Power up the receiver and wait 60 seconds for the LED to blink rapidly, indicating Wi-Fi mode. Connect your phone, tablet, or PC to the receiver's Wi-Fi (default network name: ExpressLRS RX, default password: expresslrs). Open the WebUI (default URL: http://10.0.0.1/) and enter the matching bind passphrase previously used on your radio. Save and reboot.

Note:

  • To bind the receiver a second time or to another radio, power cycle the receiver 3 times. On the third power cycle, the LED will double blink, indicating bind mode. If this method fails, you can hold down the BOOT button for 10 seconds to reset the receiver to bind mode.
  • When using the reset button, all previous settings in the receiver will be erased and will need to be reconfigured.
Wiring diagram for the ER8 receiver, showing connections for CH1-CH8, BATT, and EXT-V.

Wiring diagram for the ER8 receiver.

Operation

Channel Configuration

The ER8 receiver provides 8 PWM output channels (CH1-CH8) and a dedicated battery input (BATT). The default channel mapping is CH1 to CH1, CH2 to CH2, and so on. ExpressLRS requires CH5 to set the arming status of the RF module. It is recommended to assign CH5 to a switch on your remote control, such as the throttle cut switch, for dynamic power benefits. You can reassign channels to the receiver's CH5 output using the ExpressLRS LUA script or the Wi-Fi WebUI.

ER8 receiver with servo connections.

ER8 receiver connected to multiple servos.

Power Supply

The ER8 operates on a DC 4.5 - 8.4V power supply. It is crucial to ensure that the power supply current from your ESC's BEC (Battery Eliminator Circuit) matches the power consumption requirements of the servos you are using. For high-voltage and high-torque servos, it is recommended to use a dedicated 7.4V battery for direct power supply or a suitable high-current UBEC to maintain consistent MCU voltage for superior reliability and stability.

Internal view of the ER8 PCB showing power supply engineering for consistent MCU voltage.

Power supply engineered for servo use, maintaining consistent MCU voltage.

Telemetry

The ER8 supports automatic voltage telemetry. It can read either the built-in receiver voltage or an external battery voltage via the EXT-V port. The EXT-V (external voltage input) is accessed via a 2-pin JST-GH connector. The red wire must be soldered to the positive terminal of the battery or ESC. The maximum input voltage for the EXT-V telemetry reading is 35V. Exceeding 35V will damage the receiver. If no EXT-V power source is detected, the ER8 will default to reading the voltage on the receiver pins. Only one voltage input can be used at any given time.

The 4-pin CRSF input port is reserved for future optional telemetry sensors.

Screenshot comparison of telemetry displays on a remote control, showing built-in receiver voltage (RxBt 6.1V) and external battery voltage input (RxBt 16.7V).

Telemetry display showing built-in receiver voltage vs. external battery voltage.

Close-up of the ER8 receiver's side, showing the 4-pin CRSF input for future optional telemetry sensors and the EXT-V port for external battery voltage input.

CRSF and EXT-V input ports on the ER8 receiver.

Firmware Updates and Configuration

The ER8 receiver supports Wi-Fi updates and WebUI configuration, allowing for easy management and customization of settings.

Diagram illustrating support for WiFi updates and WebUI configuration for the ExpressLRS RX.

Wi-Fi update and WebUI configuration for ExpressLRS RX.

Maintenance

  • Keep the receiver clean and free from dust and debris.
  • Ensure all connections are secure and free from corrosion. The 2.54mm gold-plated connectors are designed for strong corrosion resistance.
  • Avoid exposing the receiver to extreme temperatures or moisture.
  • Regularly check antenna placement to ensure optimal signal reception.
Close-up image emphasizing the high-quality 2.54mm gold-plated connectors for strong corrosion resistance.

High-quality 2.54mm gold-plated connectors.

Troubleshooting

Binding Issues

  • If the receiver LED does not double blink upon first power-on, indicating bind mode, press and hold the BOOT button for 10 seconds to reset it.
  • If using the 3-power-cycle method for re-binding fails, use the BOOT button reset or the passphrase method.
  • Ensure your remote control's ExpressLRS LUA script is up-to-date and correctly configured for binding.

Telemetry Voltage Inaccuracy

  • Calibrate the telemetry voltage on your remote control. Navigate to the telemetry settings page, find the RxBt sensor, and adjust the offset until the displayed reading matches the actual battery voltage. If the discrepancy is significant, the ratio may also need adjustment.
  • Verify that the EXT-V wire is correctly soldered to the positive and negative terminals of the battery or ESC.
  • Ensure the external voltage input to the EXT-V port does not exceed 35V to prevent damage.

Servo Power Issues

  • If servos are not performing correctly, check that the ESC BEC's current output matches the power requirements of your servos.
  • For high-voltage and high-torque servos, consider using a dedicated 7.4V battery or a high-current UBEC to provide adequate power.

User Tips

  • Telemetry Calibration: Always calibrate the RxBt telemetry sensor on your remote control to ensure accurate battery voltage readings from your model.
  • Arming Switch: For optimal ExpressLRS functionality and dynamic power benefits, assign Channel 5 (CH5) to a dedicated switch on your remote control, such as the throttle cut switch.
  • Power Management: Pay close attention to your servo power requirements. If using high-voltage or high-torque servos, a separate 7.4V battery or a robust UBEC is highly recommended to prevent power-related issues.
  • Voltage Limits: Strictly adhere to the 35V maximum input for the EXT-V port to avoid damaging the receiver.
  • Easy Setup: Users have reported that the receiver is straightforward to set up and use, providing a great experience once configured.

Warranty and Support

For detailed warranty information, technical support, and additional resources, please refer to the official Radiomaster website or the user manual PDF available for download. The user manual (PDF) contains comprehensive guides and documents for your product.

You can find the user manual PDF at: Radiomaster ER8 User Manual (PDF)

Product Overview Video

Official promotional video showcasing the Radiomaster ER series receivers and their features.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.