Herdio HCS418

Contents

Herdio HCS418 4-inch In-Ceiling/In-Wall Passive Speakers User Manual

Model: HCS418 Series (HCS418, HCS418BT, HCS528, HCS528BT, HCS818, HCS818BT)

Introduction

Thank you for choosing Herdio HCS418 series in-ceiling/in-wall passive speakers. These speakers are designed to deliver high-performance stereo sound for various custom audio applications in your home or office. Their flush-mount design and paintable grilles allow for seamless integration into any decor. This manual provides detailed instructions for installation, wiring, operation, and maintenance to ensure optimal performance and longevity of your speakers.

Package Contents

Please check the box for the following items:

  • Speaker (x2)
  • Product Manual (x1)
  • Speaker Cable (5M, x2)
  • Gaskets (x2)
  • Cutout Template (x1)
  • Amplifier Box (x1, for BT models only)
  • Power Adapter (x1, for BT models only)
Contents of the Herdio speaker package, including two speakers, speaker cables, gaskets, a cutout template, and the user manual.
Figure 1: What's in the Box

Specifications

The following table outlines the technical specifications for the Herdio HCS418 series speakers:

Feature HCS418/HCS418BT (4-inch) HCS528/HCS528BT (5.25-inch) HCS818/HCS818BT (6.5-inch)
Speaker Size 4 Inch 5.25 Inch 6.5 Inch
MAX Power Output 80W 150W 160W
Sensitivity 89dB 89dB 89dB
Impedance 8 Ohms 8 Ohms 8 Ohms
Frequency Response 60-20KHz 60-20KHz 50-20KHz
Cut-Out Diameter 5.7 Inch (14.5 CM) 7.3 Inch (18.5 CM) 8 Inch (20.5 CM)
Total Speaker Diameter 6.4 Inch (16.2 CM) 6.4 Inch (16.2 CM) 6.4 Inch (16.2 CM)
Mounting Depth 2.6 Inch (6.5 CM) 2.6 Inch (6.5 CM) 2.6 Inch (6.5 CM)
Woofer Diameter 4 Inches
Tweeter Diameter 1.65 Inches
Material Plastic, Acrylonitrile Butadiene Styrene (ABS)
Sound Mode Stereo Sound Mode
Audio Crossover Full-Range
Channels 2 (2.0)
Bluetooth Version 5.0 (for BT models only)
Maximum Wireless Range 10m-20m (for BT models only)
Specific Uses Kitchen, living room, dining room, bedroom, surround ceiling, outdoor

Installation Guide

These speakers are designed for easy flush mounting in ceilings or walls. Follow these steps for a secure installation.

Video 1: Herdio HCS418PRS Unboxing and Installation Guide
  1. Prepare the Mounting Hole

    Using the provided cutout template, mark the desired location for the speaker on your drywall. Carefully cut the drywall to create the opening. Ensure there is at least a 0.5-inch (1.27 cm) clearance between the wall stud and the speaker cutout to allow the locking tabs to swivel into place.

    Diagram showing the product installation dimensions, including total speaker diameter (6.4 inches), cut-out diameter (5.7 inches), and mounting depth (2.6 inches).
    Figure 2: Product Installation Dimensions
  2. Connect Speaker Wires

    Connect the speaker cables to the speaker terminals. The red wire typically connects to the positive (+) terminal, and the black wire to the negative (-) terminal. Ensure a secure connection.

    Close-up of the speaker cable connection port, showing red wire connected to positive terminal and black wire to negative terminal.
    Figure 3: Speaker Cable Connection Port

    Note: These are passive speakers and require an external amplifier to function. This model does not include a built-in amplifier (unless it's a BT model with an amplifier box).

  3. Secure the Speaker

    Insert the speaker into the cutout. Use a screwdriver to tighten the four Phillips head screws located on the speaker frame. As you tighten, the locking tabs will swivel into place and secure the unit firmly against the rear surface of the drywall.

    A person installing a speaker into a ceiling cutout, tightening screws to secure it.
    Figure 4: Easy Installation Process
  4. Attach the Magnetic Grille

    Once the speaker is securely mounted, place the magnetic grille over the speaker. The magnets will hold it firmly in place, providing a clean, flush finish. The grilles are paintable to match your room's aesthetics.

    Diagram showing the magnetic grille attaching to the speaker frame.
    Figure 5: Paintable Grilles with Magnets

Wiring (Passive Speakers)

For passive speakers (HCS418, HCS528, HCS818), you will need an external amplifier. Connect the speaker cables from your amplifier's output terminals to the corresponding terminals on each speaker. Ensure correct polarity (red to positive, black to negative) for optimal sound quality.

  • Connect the red (+) terminal of the speaker to the red (+) terminal of your amplifier.
  • Connect the black (-) terminal of the speaker to the black (-) terminal of your amplifier.
Close-up of speaker terminals with red and black wires connected, indicating positive and negative connections.
Figure 6: Speaker Wiring Diagram

Bluetooth Operations (for BT Models Only)

For models with Bluetooth functionality (HCS418BT, HCS528BT, HCS818BT), follow these steps to pair your device:

  1. Ensure the power supply is connected to the amplifier box and the blue LED on the amplifier is flashing. This indicates it's in pairing mode.
  2. Turn on your mobile device or other Bluetooth-enabled device.
  3. Scan for Bluetooth devices and select "Herdio" from the list.
  4. Once connected, you will hear a confirmation tone, and the blue LED on the amplifier will turn solid, indicating a successful connection.
Diagram illustrating Bluetooth connection from a mobile device to the Herdio amplifier box and then to the speakers.
Figure 7: Bluetooth Connection Diagram

Maintenance

To ensure the longevity and optimal performance of your Herdio speakers, follow these simple maintenance guidelines:

  • Cleaning: Gently wipe the speaker grilles and surrounding areas with a soft, dry cloth. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish.
  • Dust Removal: Use a soft brush or a vacuum cleaner with a brush attachment on a low setting to remove dust from the grilles.
  • Avoid Moisture: While suitable for bathrooms, avoid direct water exposure. Ensure the speakers are installed in areas where they are not directly exposed to water spray.
  • Regular Checks: Periodically check the mounting screws to ensure they remain tight and the speakers are securely in place.

Troubleshooting

If you encounter any issues with your Herdio speakers, refer to the following common problems and solutions:

Problem Possible Cause Solution
No sound from speakers Incorrect wiring, amplifier off/faulty, source device issue. Check all speaker wire connections for correct polarity. Ensure amplifier is powered on and functioning. Verify audio source is playing and connected correctly.
Poor sound quality (distortion, low volume) Incorrect wiring, amplifier underpowered, damaged speaker, source quality. Check wiring for loose connections or reversed polarity. Ensure your amplifier's power output matches the speaker's requirements. Test with a different audio source.
Bluetooth connection issues (BT models) Out of range, interference, incorrect pairing. Ensure your device is within the 10-20m range. Turn off and on Bluetooth on both devices. Re-attempt pairing as per the Bluetooth Operations section. Avoid obstacles between devices.
Speaker rattling or buzzing Loose mounting, foreign object, damaged cone. Check mounting screws and ensure the speaker is tightly secured. Remove the grille and inspect for any loose debris. If the cone is damaged, contact support.

User Tips

  • Optimal Placement: For the best sound experience, consider the acoustics of your room. Placing speakers equidistant from listening positions and avoiding corners can enhance stereo imaging.
  • Amplifier Matching: Always ensure your amplifier's power output is compatible with the speakers' power handling capabilities to prevent damage and achieve clear sound.
  • Customization: The magnetic grilles are paintable. You can paint them to match your ceiling or wall color for a truly integrated look.
  • Wire Quality: Using good quality speaker wire can make a noticeable difference in sound clarity and power delivery.

FCC Requirement

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Warranty and Support

All Herdio speaker products have a 1-year Limited Warranty against defects in materials and workmanship. Proof of purchase must accompany all claims. During the warranty period, Herdio will replace any defective part and correct any defect in workmanship without charge for either parts or labor. If you have questions or require support, you can contact us:

E-mail: support@herdiotech.com

For more information, visit our website: www.Herdiotech.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.