BAOFENG UV18 Pro Max

Contents

Baofeng UV18 Pro Max GPS AM FM Six-Band Walkie Talkie User Manual

Model: UV18 Pro Max | Brand: BAOFENG

1. Getting Started

1.1 Regulations and Safety Warnings

This section outlines important safety information and regulatory compliance for the Baofeng UV18 Pro Max.

FCC Regulatory Conformance

This equipment complies with Class B digital device limits under Part 15 of FCC Rules. It generates and radiates radio frequency energy. Ensure proper installation and use to avoid harmful interference. If interference occurs, try reorienting the receiving antenna, increasing separation from other equipment, or consulting a radio/TV technician.

WARNING! MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW.

Compliance with RF Exposure Standards

The radio adheres to RF energy exposure standards and guidelines from the United States Federal Communications Commission (FCC) and the Institute of Electrical and Electronic Engineers (IEEE).

Guidelines and Operating Instructions for RF Exposure:
  • Do not remove the RF Exposure Label from the device.
  • User awareness instructions must accompany the device.
  • Do not use if operational requirements are not met.
  • Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key.
  • Keep the radio unit at least 2.5cm (1 inch) away from the face.
  • When worn on the body, use an approved holder, holster, case, or body harness.
  • Use of non-approved antennas, batteries, and accessories may exceed FCC RF exposure limits.
  • Contact your local dealer for optional accessories.

1.2 Precautions for Portable Terminals

Operating Prohibitions:

  • Do not operate in locations with fuels, chemicals, or explosive atmospheres.
  • Do not operate near blasting areas.
  • Do not operate near medical or electronic equipment vulnerable to RF signals.
  • Do not hold the product while driving.
  • Do not operate where wireless communication is prohibited.

Important Tips:

  • Do not use unauthorized or damaged accessories.
  • Keep the product at least 2.5 centimeters away from your body during transmission.
  • Avoid prolonged high-volume reception.
  • Do not place the product over an airbag or in its deployment area in vehicles.
  • Keep the product and accessories out of reach of children and pets.
  • Operate within the specified temperature range.
  • Continuous transmission may cause heat accumulation; allow for cooling.
  • Handle with care.
  • Do not disassemble, modify, or repair without authorization.

1.3 Precautions for Batteries

Charging Prohibitions:

  • Do not charge or replace batteries in locations with fuels, chemicals, or explosive materials.
  • Do not charge wet batteries; dry them first.
  • Do not charge deformed, leaking, or overheated batteries.
  • Do not charge with unauthorized chargers.
  • Do not charge in locations with strong radiation.
  • Avoid overcharging to prolong battery life.

Maintenance Instructions:

  • Clean charging connector dust regularly with a clean, dry cloth.
  • Charge batteries between 5°C and 40°C (40°F - 105°F).
  • Turn off the radio when charging a battery attached to it.
  • Do not remove the battery or unplug the power cord during charging.
  • Do not dispose of batteries in fire.
  • Do not expose batteries to direct sunlight or heat sources.
  • Do not squeeze, penetrate, or remove battery housing.

Transportation Instructions:

  • Damaged batteries must not be transported.
  • Separate batteries from metal parts to avoid short circuits.
  • The radio must be switched off and secured against accidental activation if the battery is attached.
  • Declare contents and use a Battery Shipping Label for shipment.

2. Package Contents

The Baofeng UV18 Pro Max package includes the following items:

  • 1 Radio body (UV18 Pro Max)
  • 1 Lithium-Ion battery pack
  • 1 Instruction Manual
  • 1 Belt Clip
  • 1 Desk charger (With wall-wart)
  • 1 Antenna
  • 1 Wrist Belt
  • 1 Type-C Cable
  • 1 Box

*If any item is missing, please notify your Baofeng / Pofung dealer.

Package contents for Baofeng UV18 Pro Max
Image showing the Baofeng UV18 Pro Max radio, battery, antenna, belt clip, charger, Type-C cable, and user manual.

3. Product Overview

The Baofeng UV18 Pro Max features a 1.77-inch color LCD and a full keyboard for easy operation. Below is an overview of the radio's components and their functions.

Baofeng UV18 Pro Max radio with GPS, AM/FM, Six-Band, and Type-C charging
Front view of the Baofeng UV18 Pro Max highlighting key features like GPS, AM/FM, Six-Band capabilities, and Type-C charging.

3.1 Radio Components

  1. Antenna: For transmitting and receiving radio signals.
  2. Flashlight/Emergency Alert key: Activates the built-in flashlight and emergency alert function.
  3. PTT key (Push-to-Talk): Initiates transmission.
  4. SK2 key (Customization key): Can be programmed for various shortcut functions like Monitor, FM Radio, Scan, or Search.
  5. MENU key: Accesses the main menu, selects options, and confirms settings.
  6. Numeric keypad: Used for entering frequencies, channel numbers, and DTMF codes.
  7. Power / Volume knob: Turns the radio on/off and adjusts the audio volume.
  8. Color LCD: 1.77-inch display showing frequency, channel, and status icons.
  9. Speaker/Mic Jacks: Ports for connecting external speaker/microphone accessories.
  10. MIC Input: Internal microphone for voice input.
  11. Exit Key: Used to exit menus and functions.
  12. ▲ or ▼ navigation keys: Navigates through menu options and adjusts values.
  13. Battery pack: Removable Li-ion battery for power.
  14. Type-C charging port: For direct charging of the battery pack using a Type-C cable.
  15. Battery tightening screw: Secures the battery pack to the radio body.
  16. Type-C charging indicator: LED indicating charging status when using the Type-C port.
  17. LED flashlight: Built-in light for illumination. (Note: GPS version may not have this feature).
  18. LED Status Indicator: Top LED indicating radio status (receiving, transmitting, monitoring).
Baofeng UV18 Pro Max radio with 1.77 inch LCD display
The 1.77-inch LCD display provides clear information on frequency and channel settings.
Baofeng UV18 Pro Max with USB-C charging cable connected
The Type-C port on the radio allows for convenient charging.

3.2 Status Indications (Top LED)

LED IndicationWhat it Indicates
Constant GreenReceiving Signal
Constant RedTransmitting signal
Flashes GreenMonitor mode/Scanning Receiving

3.3 LCD Icon Summary

IconDescription
RSSIOperating band signal
HTransmit power level indicator (High)
LTransmit power level indicator (Low)
♪DTMF side tone enabled
DDCS enabled
CCTCSS enabled
+Repeater access (TX shifted higher)
-Repeater access (TX shifted lower)
DDual watch enabled
🔒Keypad lock enabled
VOXVOX enabled
Confidential CallConfidential calling feature activated
NNarrowband enabled
Battery LevelBattery level indicator

3.4 Main Keypad Controls

  • MENU key: Activates the MENU, selects items, and confirms parameters. Press and hold to switch between VFO and Channel modes.
  • Navigation keys (▲/▼): Used to navigate menus and change values. Press and hold for rapid scrolling.
  • EXIT key: Exits menus and functions.
  • Numeric keypad: Inputs information or selections. In TX mode, sends corresponding DTMF codes.
  • * Key: Short press for reverse function. Press and hold for about two seconds to enable/disable keypad lock.
  • #z Key: Momentary press starts FM radio scanning. Press and hold for about two seconds to enable/disable scanner. Short press to quickly enter DTMF dialing.
  • SK2 key: Customizable function (Monitor by default). Can be set for FM Radio, Scan, Search, or VOX via CPS programming software or radio menu.

4. Setup

4.1 Installing / Removing the Battery

Installing the Battery Pack:

  1. Position the battery pack over the back of the radio.
  2. Engage the battery pack into the radio until fully seated.
  3. Tighten the screws using a coin or similar object. Do not overtighten.

Removing the Battery Pack:

  1. Loosen the screws on the back of the battery pack.
  2. Lift the bottom of the battery pack slightly.
  3. Pull the battery pack out of the radio housing.

NOTE: The Li-ION battery pack can also be charged in the battery charger.

4.2 Installing / Removing the Antenna

Installing the Antenna:

Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.

Removing the Antenna:

Turn the antenna counter-clockwise to remove it.

4.3 Installing / Removing the Belt Clip

Installing the Belt Clip:

Place the belt clip above the corresponding holes on the back of the radio, and screw it into place clockwise with the two supplied screws.

Removing the Belt Clip:

Unscrew counter-clockwise to remove the belt clip.

4.4 Installing Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

5. Battery Information and Charging

5.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. For optimal performance, fully charge/discharge the battery two or three times after initial purchase or extended storage.

Always use the specified charger provided by Baofeng. If the radio displays low battery, charge it immediately.

5.2 How to Charge (Desk Charger)

  1. Plug the AC adaptor into an AC outlet, then plug the cable into the DC jack on the back of the charger. The indicator light will blink orange.
  2. Place the battery or radio into the charger, ensuring good contact with charging terminals. The indicator light will turn red, indicating charging has begun.
  3. A full charge takes approximately 2-5 hours. The lamp will turn green when charging is complete. Remove the battery or radio.

NOTICE:

If the radio is powered on during charging, the indicator lamp may not turn green to show full charge. The radio consumes energy, preventing the charger from detecting the correct battery voltage. Always switch off the radio for proper charging indication.

LED Indicator Status:

Red LEDGreen LEDStatus
FlashingSteadyStandby (charger empty) / Error (charger with radio)
SteadyOffCharging
OffSteadyCharge complete.
Type-C charging options for Baofeng UV18 Pro Max
The radio supports versatile Type-C charging via car charger, power bank, or USB port.
Baofeng UV18 Pro Max with USB-C charging cable connected
The Type-C port on the radio allows for convenient charging.

5.3 Using the Type-C Charger

The Type-C port allows direct charging of the Li-ion battery pack.

  1. Ensure your radio is turned OFF.
  2. Plug the Type-C cable into the battery's charging port. Connect the other end to a wall power outlet.
  3. An empty battery will fully charge in 6 hours.
  4. The battery meter on the LCD will indicate charging progress.

5.4 Battery Maintenance

  • Only use manufacturer-approved batteries.
  • Never disassemble the battery pack.
  • Do not expose batteries to fire or intense heat.
  • Dispose of batteries according to local recycling regulations.

5.5 Prolonging Battery Life

  • Charge batteries at normal room temperatures.
  • Turn off the radio for faster charging when attached.
  • Do not interrupt the charging cycle by unplugging or removing the battery/radio.
  • Never charge a wet battery.
  • Replace batteries when operating time significantly shortens.
  • Battery performance reduces in freezing temperatures; keep a spare battery warm.
  • Clean battery contacts if dust interferes with charging.
  • If the battery gets wet, remove it, dry it with a towel, and place it in a plastic bag with dry rice overnight (effective for minor splashes).

5.6 How to Store the Battery

  • Store batteries at approximately 80% discharged.
  • Keep in a low-temperature, dry environment.
  • Avoid hot places and direct sunlight.
  • Cycle the battery at least every six months during long-term storage to prevent severe capacity degradation.

NOTICE:

  • Do not short circuit battery terminals.
  • Never attempt to remove the casing from the battery pack.
  • Do not store in unsafe surroundings to prevent explosion.
  • Do not put the battery in a hot environment or throw it into fire.

6. Basic Operations

6.1 Power On/Off

Turning the unit on:

Rotate the Volume/Power knob clockwise until you hear a "click". The radio will display a message or flash the LCD, followed by a frequency or channel. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".

Turning the unit off:

Rotate the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.

6.2 Adjusting the Volume

Rotate the Volume/Power knob clockwise to increase volume, and counter-clockwise to decrease. Use the monitor function (enabled via the [SK2] key) to adjust volume more easily by listening to un-squelched static.

6.3 Main Band/Sub Band Switch

In standby mode, press the MENU key to switch between the main frequency band and sub frequency bands. The highlighted band is the main, and the dimmed band is the sub.

6.4 VFO/Channel Switch

Press and hold the MENU key to switch between VFO (Frequency) and Channel (MR) display modes.

  • In Channel (MR) mode, the channel number is displayed.
  • In Frequency (VFO) mode, 'VFO' is displayed.

6.5 Frequency (VFO) Mode

In VFO mode, use the ▲ or ▼ keys to increment/decrement frequency according to the set frequency step. Frequencies can also be input directly via the numeric keypad with kilohertz accuracy.

WARNING!

Programming a channel does not automatically authorize its use. Transmitting on unauthorized frequencies is illegal. Listening is generally legal. Contact your local regulatory body for specific laws.

6.6 Channel (MR) Mode and Channel Selection

Channel (MR) mode is more practical for everyday use than Frequency (VFO) mode. Use ▲ or ▼ keys or the encoder to navigate channels. Press and hold the MENU key to switch to Channel mode.

Channel Selection:

  • Use ▲ or ▼ navigation keys.
  • Input channel numbers directly (e.g., [0][1][2] for channel 12).

6.7 Selecting a Bank

The radio supports up to 10 banks, each with a maximum of 100 channels. To select a bank:

Press MENU key, navigate to Menu > Bank, use ▲ or ▼ to select a bank, then press MENU key to switch.

6.8 Making a Call

NOTE: Press the MENU key to switch the main channel if two channels are displayed. In standby, press and hold MENU key to switch between VFO and Channel modes.

Channel mode call:

After selecting a channel, hold down the [PTT] key to transmit. Speak into the microphone. The red LED will be on during transmission.

Frequency mode call:

Press and hold the MENU key to switch to frequency mode, input the desired frequency, then press and hold the [PTT] key to transmit. Speak into the microphone. The red LED will be on during transmission.

Receive a call:

Release the [PTT] key to answer a call.

When receiving a call, the green LED is on. For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.

6.9 Using the Flashlight

Press the Flashlight/Emergency Alert key once for continuous light, again for strobe emergency mode, and a third time to turn it off. (Note: The GPS version of this walkie-talkie does not have a flashlight feature.)

6.10 Emergency Alert

To activate, press and hold the Flashlight/Emergency Alert key for 3 seconds. The radio will emit a loud siren and the flashlight will flash. Press the key again to exit. WARNING: Use only in actual emergencies.

6.11 FM Radio (FM)

The [SK2] key is defined as the FM radio on/off. Frequency range: 65-108MHz. When listening to broadcast FM, the MENU key switches between 65-75 MHz and 76-108 MHz bands.

  1. In frequency or channel mode, press [SK2] key to turn on the radio.
  2. Select the desired radio frequency with ▲ or ▼ keys or input the frequency.
  3. Press #z to automatically search for a radio station.
  4. Press [SK2] key to exit FM radio.

Note: While listening to FM, if an A/B receiving signal is detected, the radio will switch to that frequency/channel for normal transmitting/receiving. It will return to FM mode when the signal disappears.

6.12 Monitor

In standby, press and hold the [SK2] key to enter Monitor mode. This allows monitoring weak signals even if matched carrier signaling is too weak. Release [SK2] to exit. If no signal is present, it will emit noise.

6.13 Keypad Lock

The keypad lock disables all keys except the three side keys. To enable/disable, press and hold the * key for about two seconds. The radio can also be set to automatically lock the keypad after ten seconds via the menu.

6.14 Frequency Reversal

A short momentary press of the * key enables the reverse function, swapping transmit and receive frequencies. This is useful for listening to a repeater's input frequency.

6.15 TX Repeaters Tone

Press [PTT] + * key to send a 1750Hz repeater tone. This is useful for communicating through repeaters. This function works even if the keypad lock is enabled.

6.16 Weather Radio/Scan Weather Channel (NOAA)

The radio has a NOAA Weather Radio function to receive weather reports and a NOAA Weather Scan function to scan all 10 NOAA channels.

Baofeng UV18 Pro Max showing NOAA weather alerts for various natural disasters
The NOAA feature provides alerts for events like floods, hurricanes, snowstorms, fires, and earthquakes.
  1. To turn on NOAA Weather Scan, press and hold the 0 key for 3 seconds. The radio will enter Weather band mode, indicated by an icon.
  2. Press and hold the #z key for 3 seconds to start automatic scanning of all 10 channels. It will stop on active channels. Holding #z again will stop the scan.
  3. After stopping the scan, you can manually select weather channels using ▲ or ▼ keys.
  4. To exit Weather Radio broadcast mode, press the MENU key or [PTT] key.

Weather Channel Frequencies and Names:

Channel NumberRX Frequency MHzChannel NumberRX Frequency MHz
CH-01162.550CH-06162.500
CH-02162.400CH-07162.525
CH-03162.475CH-08161.650
CH-04162.425CH-09161.775
CH-05162.450CH-10163.275

NOTE: Weather Channels Wx 1 Thru 10 are Receive-only channels for NOAA and Canadian weather broadcasts. You cannot transmit on these channels.

  1. Define the SK2 side key as a Search function via CPS software or Radio Menu > Radio Setting.
  2. Briefly press the preset "Search" key. The screen will display "SEARCH SEEK..." and the radio will act as a receiver.
  3. If an effective frequency is received, it will be displayed. If CTCSS/DCS is present, it will also be displayed.
  4. Press the MENU key to save the Search frequency and CTCSS/DCS to a channel.

Note: During frequency Search, press the # key to switch between UHF or VHF bands.

7. Advanced Features

7.1 GPS Features

The Baofeng UV18 Pro Max includes GPS functionality for positioning and location sharing.

Baofeng UV18 Pro Max showing GPS+BDS Positioning and Location Sharing
The radio supports GPS+BDS positioning for location sharing.
  • GPS does not require an APRS cable.
  • A simple compass is displayed on the screen to show the location.
  • For detailed operation steps of the GPS feature, please refer to supplementary video tutorials if available, as the printed manual may not cover all GPS operations.

Note: The GPS version of this walkie-talkie does not have a flashlight feature.

7.2 Scanner

The radio has a built-in scanner for VHF and UHF bands. In Frequency (VFO) mode, it scans in steps. In Channel (MR) mode, it scans your channels.

To enable, press and hold the #z key for about two seconds. Change scanning direction with ▲ or ▼ keys. Press and hold #z again to exit.

7.2.1 Frequency Ranger:

In frequency mode, precisely set the frequency sweep range by inputting start and end values via the keyboard (e.g., 144146 for 144.000-146.000MHz).

7.2.2 Scan Modes:

The scanner has three operation modes:

  • Time Operation (TO): Scanner stops on a signal, then resumes after a preset time.
  • Carrier Operation (CO): Scanner stops on a signal, then resumes after a preset time with no signal.
  • Search Operation (SE): Scanner stops on a signal. Press and hold #z to resume.

7.2.3 Scan Sub-Code (CTCSS/DCS):

To search for a CTCSS code:

  1. In VFO mode, enter a known frequency (e.g., 144.525).
  2. Press MENU key to enter menu >> Scan >> 3 Scan Sub-Code.
  3. Use ▲ or ▼ to select CTCSS.
  4. Press MENU key to start scanning CTCSS codes. It will stop on a valid code.
  5. Press MENU key to store the scanned CTCSS code and exit. The C icon will appear. Hold PTT to callback.

To search for a DCS code, follow similar steps, selecting DCS instead of CTCSS. The D icon will appear.

7.2.4 Sub-Code Scan Storage:

Scanned CTCSS/DCS codes can be stored as TX, RX, or both for the current channel/frequency mode. To save:

  1. Press MENU key to enter menu >> SCAN >> 4 Scan Memory.
  2. Press MENU key and use ▲ or ▼ to select:
    • ALL: Stores as both received and transmitted CTCSS/DCS.
    • DECODER: Stores as receiver CTCSS/DCS only.
    • ENCODER: Stores as transmitted CTCSS/DCS only.
  3. Press MENU key to save and return.

Note: Only save when a valid CTCSS/DCS code is scanned and stopped.

7.3 DTMF (Dual Tone Multi-Frequency)

DTMF is an in-band signaling method using dual sinusoidal signals, commonly used in two-way radio for automation and remote control (e.g., amateur radio repeaters).

DTMF Frequencies and Corresponding Codes:

1209Hz1336Hz1477Hz1633Hz
697Hz123A
770Hz456B
852Hz789C
941Hz*0#D

The radio fully implements DTMF, including A, B, C, and D codes. Numeric keys, *, and #z correspond to DTMF codes. A, B, C, and D codes are located on the MENU, ▲, ▼, and EXIT keys respectively.

To send DTMF codes, press the key(s) while holding down the PTT key.

7.3.1 Call With Signaling:

A call with signaling targets a specific ID on a channel with a preset DTMF signaling code. Configure signaling code, mute mode, and PTT-ID via CPS Programming Path >> Programming >> DTMF System >> Call Code, Call Name >> ANI ID.

7.3.2 DTMF Manual Dial:

Short press #z key to enter DTMF manual dialing. Enter the DTMF number in the required format, then press and hold the PTT key to make a DTMF call.

  • Private call: Confirm ID with #z, then press and hold PTT. (e.g., [1][2][3]#z for ID 123).
  • Group call: Confirm ID with *, then press and hold PTT. (e.g., [1][2]** for group with prefix 12).
  • All call: Enter *#z, then press and hold PTT.

7.4 Dual Watch

This feature allows monitoring two channels simultaneously. The radio features Dual Watch (single receiver) and can lock the transmit frequency to one of the monitored channels.

Enabling or disabling Dual Watch mode:

  1. Press the MENU key to enter the main menu.
  2. Enter 3 on the numeric keypad for Radio Settings.
  3. Press MENU key to confirm, enter 14 for Dual Watch.
  4. Press MENU key to select.
  5. Use ▲ or ▼ keys to enable or disable.
  6. Press MENU key to confirm.
  7. Press EXIT key to return to the previous menu.

When enabled, the 'D' icon is displayed. To disable, repeat the steps and select "OFF".

7.5 Manual Programming (Channels Memory)

The radio has 999 memory channels, each storing receive/transmit frequencies, power, signaling, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier.

Frequency Mode (VFO) vs. Channel Mode (MR):

  • VFO Mode: For temporary frequency assignments or quick field programming.
  • MR Mode: For selecting preprogrammed channels.

In standby mode, press and hold the MENU key to switch between VFO and MR modes.

Example 1: Programming a Channel Repeater Offset with CTCSS Tone

RX = 432.55000 MHz, TX = 437.55000 MHz (+5 Offset), TX CTCSS tone 123.0

  1. Press MENU key to switch between menus.
  2. Press and hold MENU key to set the radio to VFO mode.
  3. Input [4][1][7][1][0] to delete prior data in channel 10.
  4. Input [4][5][1][2][3][0] to select TX encode tone 123.0 (CTCSS).
  5. Input [4][1][4][0][5][0] to enter OFFSET frequency 5.00MHz.
  6. Input [4][1][5][2] to select positive offset.
  7. Enter RX frequency (e.g., 43255000).
  8. Input [4][1][6][1][0] to enter the same channel (Ex 10).
  9. Press and hold MENU key to return to MR mode.

Example 2: Programming a Simplex Channel with CTCSS Tone

RX = 432.6500 MHz, TX CTCSS tone 123.0

  1. Press MENU key to switch between menus.
  2. Press and hold MENU key to set the radio to VFO mode.
  3. Input [4][1][7][1][0] to delete prior data in channel 10.
  4. Input [4][5][1][2][3][0] to select TX encode tone 123.0 (CTCSS).
  5. Enter RX frequency (e.g., 43265000).
  6. Input [4][1][6][1][0] to enter the same channel (Ex 10).

7.6 Repeaters Programming

These instructions assume you know your repeater's transmit/receive frequencies and are authorized to use them.

  1. Press and hold the MENU key to set the transceiver to VFO mode.
  2. Use the numeric keypad to enter the repeater's output (receive) frequency.
  3. Input [4][1][4] to get the offset frequency.
  4. Use the numeric keypad to enter the specified frequency offset.
  5. Press MENU key to confirm and save.
  6. Input [4][1][5] to get the offset direction.
  7. Use ▲ or ▼ keys to select plus (positive) or minus (negative) offset.
  8. Press MENU key to confirm and save.
  9. Optional: Save to memory (see Manual Programming) or set up CTCSS.
  10. Press EXIT key to exit the menu.

NOTE: If connection problems occur, recheck settings. Some amateur repeaters use a 1750Hz tone burst to open. See "1750Hz Tone-burst" section. If issues persist, contact your radio system administrator.

7.7 Amateur Radio Setup

For amateur radio use, it's recommended to turn off certain features for broader compatibility:

Radio Settings:

  • Turn off ANI, DTMFST, PTT-ID, and PTT-LT (menu items 18-20).
  • Turn off Squelch Tail Elimination (Tail) (menu item 23).
  • Turn off Roger Beep (ROGER) (menu item 10).

Program Channel:

  • Set bandwidth to Wide (menu item 5).
  • Turn off DCS and CTCSS (menu items 6-9).
  • Turn off Signaling code and SPK-Mute (menu items 11 and 13).

8. Main Menu Functions (Radio Settings)

The menu allows operations like selecting Banks, setting SCAN, Radio Settings, Program Channels, and viewing Radio Information.

8.1 Basic Use of Menus

  1. Press the MENU key to enter the main menu.
  2. Use ▲ or ▼ keys to navigate menu items.
  3. Press the MENU key to select an item.
  4. Use ▲ or ▼ keys to navigate sub-items.
  5. Press the MENU key to select a sub-item.
  6. Use ▲ or ▼ keys to select the desired parameter.
  7. To confirm, press MENU key (saves setting).
  8. To cancel, press EXIT key (resets item).
  9. To exit menu at any time, press the PTT key.

8.2 Using Shortcuts

Each menu item has a numerical value for direct access.

  1. Press the MENU key.
  2. Enter the menu item number via the numeric keypad.
  3. Press the MENU key to enter the item.
  4. Select parameter using arrow keys or numerical shortcut code.
  5. Confirm with MENU key or cancel with EXIT key.

Quick Access Shortcuts:

  • MENU + 1: Banks selection (up to 10 banks, 100 channels each).
  • MENU + 2: Scan Settings (VFO frequency range, Scan mode, Scan Sub-Code, Scan Memory).
  • MENU + 3: Radio Settings (general settings).
  • MENU + 4: Program Channel (Alias, TX/RX Frequency, TX Power, Bandwidth, Display mode, Channel Memory).
  • MENU + 5: Radio Information (ANI ID, Firmware version, Hardware version).

8.3 Radio Settings (MENU + 3)

(1) Step frequency (Step) – MENU + 1

Selects the desired frequency step: 2.5K, 5.0K, 6.25K, 10.0K, 12.5K, 20.0K, 25.0K, 50.0K, 100K. (Cannot be modified in channel mode).

(2) Squelch level (Squelch) – MENU + 2

Adjusts squelch in 5 levels:

  • OFF: Open squelch (detects all signals, including noise).
  • Levels 1-5: Level 1 (lowest squelch), Level 5 (highest squelch). Higher levels receive only strongest signals.

(3) Power save (Power Save) – MENU + 3

Reduces battery consumption in standby. Turning it on is more power efficient but may cut off initial syllables of RX.

(4) VOX Function (Vox Switch) – MENU + 4

Enables hands-free calls. Communication starts automatically when you speak into the microphone.

  • ON: Activates VOX.
  • Off: Turns off VOX.

(5) VOX Level (Vox Level) – MENU + 5

Selects VOX sensitivity level from 1 (least sensitive) to 9 (most sensitive). (VOX is not enabled in scan or FM radio mode).

(6) VOX Delay – MENU + 6

Sets VOX delay (0.5 - 2.0 seconds, default 1 second) to extend transmission time and prevent early cut-off.

(7) Time-Out-Timer (TOT) – MENU + 7

Sets maximum continuous transmission duration (Off, 15-180 seconds, default 60 seconds) to prevent single users from occupying a channel. If set to OFF, PTT can be held indefinitely.

(8) Transmission Overtime Alarm (TOA) – MENU + 8

Defines a duration (0-10 seconds, default Off) before transmission terminates. If TOT is enabled and transmission reaches the pre-set time, the transceiver warns you and the TX red indicator blinks.

(9) Voice prompts function (Voice) – MENU + 9

Activates voice prompts for operations/selections.

(10) Language selection (Language) – MENU + 10

Selects language for LCD display and operation prompts (e.g., Chinese, English).

(11) Roger beep (ROGER) – MENU + 11

When PTT is released, the radio beeps to confirm transmission end to other users.

(12) Keypad beep (Beep) – MENU + 12

Enables a beep sound every time a key is pressed.

(13) Backlight (Backlight) – MENU +13

Adjusts auto-off time of the display backlight (5S-20S adjustable, Always On). (This function is valid when power save is off).

(14) Power on image (Power on Display) – MENU + 14

Sets display mode when radio powers on:

  • PICTURE: Displays preset startup picture.
  • MESSAGE: Displays welcome message.
  • VOLTAGE: Displays power voltage.

(15) Dual Watch Operation (Dual Watch) – MENU + 15

Allows receiving frequencies on both Channel A and Channel B simultaneously. If a signal is detected, the ▲ or ▼ pointer blinks on the corresponding channel/frequency. The 'D' icon is displayed. (Parameters of A/B channels can be changed).

(16) Auto Keypad Lock (AutoLock) – MENU + 16

Automatically locks keypad after 10 seconds to prevent accidental presses. Can be manually activated/deactivated by pressing and holding the * key.

(17) Alarm Mode (Alarm Mode) – MENU + 17

Sets tone alarm/code alarm/site alarm:

  • Site: Speaker emits alarm tone, radio does not transmit.
  • Tone: Speaker emits alarm tone, radio transmits it.
  • Code: Speaker emits alarm tone, radio transmits it followed by ANI-ID code.

Press and hold [SK1] key for 3 seconds to start the alarm tone.

(18) Local Alarm Tone (Alarm Tone) – MENU + 18

Determines if an alarm whistle is emitted locally when the emergency alarm function is triggered.

(19) ANI-ID (ANI-ID) – MENU + 19

Displays/allows editing of the ANI code (up to 5 digits). ANI-ID is sent when alarm is active and during DTMF signaling calls.

(20) DTMFST (DTMFST) – MENU + 20

Determines when DTMF Side Tones are heard:

  • Off: No DTMF Side Tones.
  • DT-ST: Side Tones heard only from manually keyed DTMF codes.
  • ANI-ST: Side Tones heard only from automatically keyed DTMF codes.
  • DT+ANI: All DTMF Side Tones heard.

(21) PTT-ID (PTT-ID) – MENU + 21

Decides when ANI-ID code is sent during transmission:

  • Off: Disables DTMF signaling for current channel/VFO mode.
  • BOT: Code sent when PTT is pressed.
  • EOT: Code sent when PTT is released.
  • BOTH: Code sent when PTT is pressed and released.

(22) Signal code sending delay (PTT-DLY) – MENU + 22

Sets PTT-ID signal code sending delay time (100-3000ms).

(23) 1750Hz Repeater Tone (ALERT) – MENU + 23

Selects repeater tone frequency (1000Hz, 1450Hz, 1750Hz, 2100Hz). To send, hold down [PTT] + * key. Works even with keypad lock enabled.

(24) Squelch tail elimination (TAIL) – MENU + 24

Eliminates squelch tail noise between handhelds communicating directly (no repeater) by muting audio with a 55 Hz or 134.4 Hz tone burst.

(25) SK2 function definition (Press SK2) – MENU + 25

Customizes SK2 key functions:

  • FM RADIO: FM radio on/off.
  • SCAN: Scan on/off.
  • SEARCH: One touch Search on/off.
  • VOX: Vox on/off.

(26) Reset (Reset) – MENU + 26

Resets transceiver to factory-programmed settings. Two types:

  • VFO: Menu Reset.
  • ALL: Menu and channel Reset.

9. Program Channel (MENU + 4)

Channel configuration applies only to the current channel and allows modification of its name, RX/TX frequency, CTCSS/DCS, scan list inclusion, working mode, and memory.

(1) Channel name (CHNAME) – MENU +1

Edit channel name (up to 8 characters, A-Z, 0-9). Confirm with MENU key, exit with EXIT key.

(2) RX Frequency – MENU +2

Input RX frequency via keypad. Save with MENU key, return with EXIT key.

(3) TX Frequency – MENU +3

Input TX frequency via keypad. Save with MENU key, return with EXIT key.

(4) Transmit power (Tx Power) – MENU +4

Set TX power for current channel (High/Low).

(5) Wide/Narrow Bandwidth – MENU +5

Select bandwidth:

  • Wide: 25 KHz.
  • Narrow: 12.5 KHz.

(6) Receiving CTCSS (Rx CTCSS) – MENU +6

Add CTCSS codes to channels for private communication (50 groups of CTCSS tones).

(7) Receiving DCS (Rx DCS) – MENU + 7

Add DCS codes to channels for personal communication. Options:

  • Off: Off.
  • D023N-D754N: Normal DCS.
  • D023I-D754I: Inverse DCS.

(208 groups of normal and inverse DCS codes).

(8) Transmitting CTCSS (Tx CTCSS) – MENU +8

Set CTCSS tone in TX mode (Off or 67.0 to 254.1 Hz).

(9) Transmitting DCS (Tx DCS) – MENU+9

Activate DCS codes in TX mode (Normal R-DCS or Inverted R-DCS).

(10) Call Encryption (Encryption) – MENU +10

If CTCSS/DCS is configured and encryption is on, communication remains private. The encryption icon will be displayed.

(11) Signal code (Signaling) – MENU +11

Selects one of 20 programmed DTMF codes (up to 3 digits).

(12) Working Mode (CH-MDF) – MENU +12

Sets display mode of current channel:

  • NAME: Channel name.
  • FREQ: Frequency Mode.
  • CH: Channel Mode.

(13) Monitor (SP-MUTE) – MENU +13

Opens monitor if specific conditions are met:

  • QT: When radio receives correct CTCSS tones.
  • QT + DTMF: When radio receives correct CTCSS tones and DTMF code.
  • QT*DTMF: When radio receives correct CTCSS tones OR DTMF code.

(14) Scan Add (Scan Add) – MENU+14

Adds current channel to scan group:

  • On: Turn on scan function.
  • Off: Do not scan.

(15) Busy Channel Lock (Busy Lock) – MENU+15

Prevents transmission if selected channel is in use by other radios. Radio will beep and not transmit. Release PTT and transmit when channel is free.

(16) Channel Memory - (CH-Memory) – MENU +16

Creates new or modifies existing channels (1-100) for MR/Channel Mode access.

(17) Channel Delete (CH-Delete) – MENU +17

Deletes programmed information from a specified channel (1-100).

(18) Frequency offset (Offset) – MENU + 14 (in frequency mode)

Sets deviation between TX and RX (00.000-99.998MHz).

(19) Frequency offset direction (Direction) – MENU + 15 (in frequency mode)

Sets direction of frequency offset:

  • OFF: No offset.
  • Plus: Positive offset (+).
  • Minus: Negative offset (-).

10. Troubleshooting Guide

PhenomenaAnalysisSolution
You cannot turn on the radio.Battery improperly installed, battery power low, dirty/damaged battery contacts, low battery voltage.Remove/reattach battery, recharge/replace battery, clean/replace battery.
During receiving, the voice is weak or intermittent.Low volume level, loose/incorrectly installed antenna, blocked speaker.Increase volume, turn off/remove/reattach antenna, clean speaker.
You cannot communicate with other group members.Inconsistent frequency/signaling type, too far from others.Verify TX/RX frequency and signaling type, move closer to others.
You hear unknown voices or noise.Interrupted by radios on same frequency, radio in analog mode with no signaling.Change frequency/adjust squelch level, request dealer to set signaling.
You are unable to hear anyone because of too much noise and hiss.Too far from others, unfavorable position (blocked by buildings/underground), external disturbance (EMI).Move closer to others, move to open/flat area and restart, stay away from interfering equipment.
The radio keeps transmitting.VOX turned on, headset not installed.Turn off VOX, check headset.

NOTE: If these solutions do not resolve your problems, please contact your dealer for technical support.

11. Technical Specifications

General

ParameterValue
Channel Capacity1000
Channel Spacing25.0 KHz/12.5 KHz
Input Voltage7.4 VDC
Battery Life (5% TX, 5% RX, 90% Standby)Li-on: 15 hours @ 5 watts
Current Drain (Stand-by)45 mA
Current Drain (Receive)200 mA
Current Drain (Transmit)≤1.6 A @ High Power, ≤1.2 A @ Low Power
Operating temperature-10°C to 60°C
Antenna Impedance50Ω
Radio Dimensions127mm X 69mm X 38mm (not including antenna)

Transmitter

ParameterValue
Frequency Range (TX)136 to 174 MHz, 220 to 260 MHz, 400 to 480 MHz
RF Output Power2 or 5 Watts Max
Modulation16K0F3E/11K0F3E
Spurious Emission-16 dBm<1GHz, -16 dBm>1GHz
Frequency Stability±2.5 ppm
Audio Distortion≤5%
FM Hum & Noise40 dB

Receiver

ParameterValue
Frequency Range136 to 174 MHz, 220 to 260 MHz, 400 to 520 MHz, FM 78 to 108MHz, AM 108 to 136MHz, 350 to 390 MHz
Sensitivity (12 dB SINAD)-120 dBm
Adjacent Channel Selectivity-60 dBm
Intermodulation and Rejection-70 dBm
Rated Audio Power Output1.0 Watts @ 16 Ω
Rated Audio Distortion≤5%

NOTE: All specifications may be modified without prior notice or liability.

12. Warranty and Support

Baofeng provides a ONE YEAR WARRANTY for the radio body and THREE MONTHS for the battery, charger, and other accessories.

Shipping costs for warranty repair/exchange/return are to be paid by the buyer.

For technical support or warranty claims, please contact your dealer. Ensure correct shipping address is provided before sending any parcel.

Manufacturer: Fujian Baofeng Electronics Co.,Ltd.

Address: Changfu Industrial Bank Xiamei, Nan'an, Quanzhou, Fujian, China

Email: wangjianhui@baofengradio.com

Website: http://www.baofengradio.com

13. PDF User Manual

A comprehensive user manual in PDF format is available for detailed instructions and diagrams.

You can view or download the official user manual (PDF) here.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.