1. Introduction
The ORVIBO MixPad M2 is a super smart gateway panel designed to centralize control of your smart home devices, including lights, air conditioners, and curtains. Featuring a touch screen interface, voice control, and multi-protocol support (Zigbee, Wi-Fi, Bluetooth), it offers a seamless and intuitive smart home experience. This manual provides detailed instructions for installation, operation, and maintenance of your MixPad M2.
2. Setup and Installation
2.1 Pre-installation Checklist
Before beginning installation, ensure the following requirements are met:
- A standard concealed bottom box with a depth of at least 5cm is reserved.
- Use round screw columns or round iron ear buckles for mounting.
- The recommended installation height from the ground is 1.35m.
- Ensure reliable Wi-Fi wireless network coverage near the device for networking.
- If installing alongside an ORVIBO MixSwitch super smart switch, the center spacing of the bottom boxes must be 89.6mm. It is recommended to use the ORVIBO special millimeter frame for proper alignment.
2.2 Wiring Plan
The MixPad M2 requires a zero-fire wire power supply. Follow the wiring instructions carefully:
- Reserve 220V power supply zero (N) and live (L) wires.
- Reserve 4 loop light control wires (L1, L2, L3, L4).
2.3 Physical Installation
The MixPad M2 is designed for in-situ replacement and non-destructive installation using a national standard 86 bottom box.
3. Operating Instructions
3.1 Touch Screen Control
The MixPad M2 features an IPS high-definition touch screen with a 180° ultra-wide viewing angle, providing a clear and intuitive interface for controlling your smart devices. Simply tap on the icons to manage lights, adjust air conditioners, or open/close curtains.
3.2 Voice Control
Utilize the built-in One Step™ voice interaction technology for hands-free control. The optimized microphone noise reduction algorithm enhances sensitivity, allowing for voice commands up to 7 meters away. Simply speak your commands to control lights and other connected devices.
3.3 App Control (Zhijia 365 APP)
The MixPad M2 can be controlled remotely via the Zhijia 365 (Smart Home 365) mobile application. This allows you to manage your smart home devices from anywhere, ensuring you never forget to turn off appliances when you leave home.
3.4 Infrared Remote Control
The MixPad M2 features a built-in, hidden intelligent infrared remote control. This allows it to control over 9600+ brands of traditional home appliances, effectively transforming them into smart devices. The remote control has an effective range of up to 20 meters.
3.5 Intercom Function
The MixPad M2 supports screen-to-screen dialogue, enabling easy communication between different rooms in a large house without needing to shout. It can also integrate with smart door locks for visual intercom, allowing you to see and speak with visitors from any MixPad M2 panel.
3.6 Video Demonstration
4. Maintenance
To ensure the longevity and optimal performance of your ORVIBO MixPad M2, follow these simple maintenance guidelines:
- Cleaning: Gently wipe the touch screen and device surface with a soft, dry, lint-free cloth. Avoid using abrasive cleaners, solvents, or aerosol sprays, as these can damage the screen or finish.
- Software Updates: Periodically check for and install software updates through the Zhijia 365 APP to ensure you have the latest features and security enhancements.
- Environmental Conditions: Keep the device away from direct sunlight, excessive heat, and moisture. Ensure it is installed in a well-ventilated area.
5. Troubleshooting
If you encounter issues with your MixPad M2, try the following troubleshooting steps:
- Device Unresponsive: If the touch screen is unresponsive, try restarting the device by cycling its power (turn off the circuit breaker for a few seconds, then turn it back on).
- Connectivity Issues: Ensure your Wi-Fi network is active and the MixPad M2 is within range. Check your router settings and ensure no firewalls are blocking the device's connection. Re-pair the device with the Zhijia 365 APP if necessary.
- Voice Control Not Working: Ensure you are speaking clearly and within the 7-meter range. Check for any background noise that might interfere with voice recognition.
- Infrared Control Problems: Ensure there are no obstructions between the MixPad M2 and the appliance you are trying to control. Verify that the appliance brand and model are correctly configured in the app.
- Lights/Appliances Not Responding: Check the wiring connections (N, L, L1-L4) to ensure they are secure. Verify that the load does not exceed the maximum capacity (400W per path, 1200W total).
If problems persist, please contact ORVIBO customer support for further assistance.
6. Specifications
| Feature | Specification |
|---|---|
| Product Model | MixPad M2 (V32X) |
| Product Size | 86mm × 86mm × 35.8mm |
| Input Voltage | AC220V, 50/60Hz, 2A |
| Number of Load Paths | 4 gang |
| Load Type | Incandescent lamps, LED lamps, Energy-saving lamps, etc. |
| Maximum Load | 400W per path, Total 1200W |
| Communication Methods | Wi-Fi, Bluetooth, Zigbee |
| Working Environment Temperature | -15℃ to 50℃ |
| Working Environment Humidity | ≤85%RH |
| Infrared Control | Supported (9600+ brands, 20m range) |
| State of Assembly | Ready-to-Go |
| Certification | CE |
7. User Tips
- Optimize Wi-Fi: For the best performance and responsiveness, ensure your MixPad M2 is connected to a stable 2.4GHz Wi-Fi network.
- Explore App Features: Take time to explore all the functionalities within the Zhijia 365 APP, including scene creation, automation rules, and device grouping, to fully customize your smart home experience.
- Voice Command Practice: Experiment with different voice commands to find what works best for your accent and speech patterns.
8. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official ORVIBO website or contact your local distributor. Keep your purchase receipt as proof of purchase for any warranty claims.
