FUZRR ES6030

Contents

FUZRR ES6030 Transformer Turns Ratio Tester User Manual

Comprehensive guide for safe and effective operation of your ES6030 device.

1. Safety Rules and Precautions

Thank you for purchasing our transformer turns ratio tester. Before you use the instrument for the first time, in order to avoid possible electric shock or personal injury, please be sure to read in detail and strictly observe the safety rules and precautions listed in this manual.

In any case, special attention should be paid to safety when using this instrument.

  • The instrument is designed, manufactured and tested in accordance with IEC61010 safety specifications.
  • Notice the labeled text and symbols on the body of this instrument.
  • Before use, it should be confirmed that the instrument and accessories are intact, and the insulation of the instrument and test line is not broken exposed, No broken wires to use.
  • During measurement, it is strictly prohibited to touch the exposed conductors and the circuit being measured.
  • Verify that the wire connection plugs are tightly inserted into the instrument connector.
  • Do not measure in flammable locations, sparks may cause an explosion.
  • Discontinue use of the instrument if metal is exposed due to breakage of the housing or test cable during use.
  • Do not place and store the instrument for a long time in a hot and humid place or under direct sunlight.
  • Pay attention to the measurement range specified for this instrument and the environment in which it is used.
  • The use, disassembly, calibration, and maintenance of this instrument must be carried out by authorized and qualified personnel.
  • If continued use poses a danger due to this instrument, stop using it and seal it immediately deposit, to be handled by an authorized and qualified body.
  • The "!" safety warning symbols in the instrument and in the manual must be strictly followed by the user in this manual. Allow for safe operation.

2. Introduction

The ES6030 transformer turns ratio tester adopts microprocessor technology for measurement calculation and automatic control, which can quickly and easily measure the actual transformer ratio and group. It is mainly used in the power industry to measure the transformer ratio and group, and at the same time, it is used by transformer manufacturers and distributors to measure the transformer parameters.

The ES6030 transformer ratio tester consists of the host, monitoring software, test line, communication line, and so on. The host has a charging function without the need to find power on site, a full-color large-screen LCD display, and the language can be chosen between Chinese or English. It features convenient touch-screen operation, port anti-overload function, and large-capacity storage of 500 groups of data. Upper computer software provides historical data reading, access, save, and other functions.

Please note: Since 2026, the ES6030 color has changed to green, but the specifications and functions remain unchanged.

FUZRR ES6030 Transformer Turns Ratio Tester (Green Version)

Image: The ES6030 Transformer Turns Ratio Tester in its updated green color.

3. Specifications

3.1. General Specifications

FeatureDescription
FunctionMainly used for ratio and group testing of three-phase transformers, single-phase transformers, PT and CT. Supports blind testing of three-phase transformers and Z-type transformers.
Type of test productSingle-phase transformer, three-phase transformers, Z-type transformers, PT, CT
Variable ratio range0.9~10000
Overload protectionYes
Power sourceDC9.6V 3800mAh high capacity lithium battery
Charging functionYes
Display mode5-inch touchscreen (854dots × 480dots) full-color LCD display
Interactive modeTouch screen & button
LCD sizeLength × width: 108 mm × 65mm
Instrument sizeLength × width × height: 229mm × 166mm × 74mm
Mobile APPYes, Bluetooth connection
Computer connectYes, the USB cable connection
Data storage500 groups
Data accessData access function
Battery voltageReal-time display of battery power indicates that the battery should be charged in time when the voltage is low
Auto shut offAutomatic shutdown can be set for 1 to 30 minutes
Power dissipation (Standby)Approx. 2W (100% brightness)
Power dissipation (Measured)12W Max
Instrument Weight1.5kg (including battery)
Test cables Weight1.7kg
Working temperature and humidity-10℃~40℃; below 70%rh
Store temperature and humidity-20℃~60℃; below 70%rh
Insulation resistanceAbove 10 MΩ (500V between circuit and housing)
Withstand voltageAC 3700V/rms (between circuit and enclosure)
Electromagnetic propertyIEC61010-4-3, radio frequency≤1V/m
Suitable for safety RegulationsIEC61010-1, CAT III 600V, pollution class2

3.2. Measurement Range and Accuracy

Measure the radio rangeResolution radioAccuracy
0.9 ≤ TTR < 100.0001±0.2% ± 2dgt
10 ≤ TTR < 1000.001±0.2% ± 2dgt
100 ≤ TTR < 10000.01±0.2% ± 2dgt
1000 ≤ TTR < 20000.1±0.2% ± 2dgt
2000 ≤ TTR < 100000.1±0.5% ± 2dgt
10000 ≥ TTR1--

4. Instrument Structure

The ES6030 features a user-friendly interface with clearly labeled ports and buttons.

ES6030 Transformer Turns Ratio Tester front view with labels

Image: Front view of the ES6030 tester, showing the display and control buttons.

ES6030 Transformer Turns Ratio Tester dimensions

Image: ES6030 tester with dimensions indicated (229mm x 166mm x 74mm).

4.1. Component Identification

No.Component
1HV side A phase terminal
2HV side B phase terminal
3HV side C phase terminal
4LV side A phase terminal
5LV side B phase terminal
6LV side C phase terminal
7USB PORT
8Power button
9Confirmation key
10Return key
11Test key
12Color screen
13Multi-function key
14Right button
15Left button
16Down button
17Upper button
18Charging port

4.2. Iconography

The device uses both silicone keypad buttons and touch screen buttons. Here's a guide to their functions:

4.2.1. Silicone Keypad

IconNameNote
Up arrow iconUpper keySelect upwards
Down arrow iconDown keySelect downwards
Left arrow iconLeft keySelect to the left
Right arrow iconRight keySelect to the right
Multiplex key iconMultiplex keyEquivalent to touching the bottom left button of the screen, including deleting, saving, sound, etc.
Power button iconPower buttonSwitching power supply
Confirm key iconConfirm keyConform or checked.
Return key iconReturn keyReturn to the previous screen
Test key iconTest keyStart testing

4.2.2. Touch Screen Buttons

IconNameNote
OKConfirm keyConform or checked.
Return key iconReturn keyReturn to the previous screen
Up arrow iconUpper keySelect upwards
Down arrow iconDown keySelect downwards
Left arrow iconLeft keySelect to the left
Right arrow iconRight keySelect to the right
Delete key iconDelete keyDelete all test records.
TimeTime keyEnter the set time interface
Sound off iconSound keySet the buzzer switch.
SaveSave keySave the test record
BLEBluetooth keySet up Bluetooth on or off.
EN/CNLanguage switchingSwitch between Chinese and English
TESTTest keyStart testing

4.2.3. Other Icons

IconNote
Backlight adjustment iconUsed for adjusting the brightness of the backlight.
Battery level display iconBattery level display
Charging status display iconCharging status display
Bluetooth iconBluetooth is displayed in the upper right corner of the large screen when it is switched on.
View test record iconView test record

5. Setup

5.1. Switching On and Off

Pressing the red "power button" in the off state will turn the power on. Pressing the red "power button" again in the on state will turn the power off.

5.2. Interface Introduction

The main interface provides access to different test modes and settings.

ES6030 Main Interface Screen

Image: Main interface of the ES6030, showing options for Three phase, Single phase, Z-type, Set, View, and OPI.

5.3. Time Setting

To set the time, navigate to the time setting screen. You can adjust the year, month, day, hour, and second by sliding the values up and down. Confirm with the OK button to update the system time.

ES6030 Time Setting Screen

Image: Time setting screen, allowing adjustment of date and time.

5.4. General Settings

From the main interface, click the "Set" icon to enter the system settings interface.

ES6030 Settings Interface

Image: Settings interface, showing options for Backlight, Shutdown, Time, EN/CN, and BLE.

  • Backlight Setting: Drag the icon to the left or right to adjust the brightness.
  • Shutdown Time Setting: Press the left and right keys to select 1~30 minutes auto shutdown. If there is no operation, the tester will turn off automatically after this time.
  • Sound Settings: Click the sound icon to switch the sound on and off.
  • Language Switching: Click "EN/CN" to switch between Simplified Chinese and English.
  • Bluetooth Setting: Click "BLE" to switch Bluetooth on/off. When Bluetooth is on, the Bluetooth icon is displayed in the upper right corner of the screen.

5.5. Wiring Methods

5.5.1. Single-Phase Transformer Wiring

Single-phase transformer wiring diagram

Image: Diagram showing how to connect the ES6030 to a single-phase transformer.

Connect the two ports on the high-voltage side of the transformer to the tester's UA and UB terminals, and the two ports on the low-voltage side of the transformer to the tester's Ua and Ub terminals.

5.5.2. Three-Phase Transformer Wiring

Three-phase transformer wiring diagram

Image: Diagram showing how to connect the ES6030 to a three-phase transformer.

Connect the three ports (A, B, C) on the high-voltage side of the transformer and the three terminals (UA, UB, UC) of the tester according to the same name. Similarly, connect the three ports (a, b, c) on the low-voltage side of the transformer and the three terminals (Ua, Ub, Uc) of the tester according to the same name.

6. Operating Instructions

6.1. Single-Phase Transformer Test Operation

In the main interface, click on the "Single phase test" icon to enter the test setup interface.

Single-phase test setup interface

Image: Single-phase test setup screen, showing Sample, High, Low, TS, and RT parameters.

  • Specimen No.: Adjust the value to distinguish the tested transformer. This parameter does not affect the test results.
  • Rated HV: The rated voltage of the high voltage side, used to calculate the ratio error and deduce the tap position.
  • Rated Low Voltage: The rated voltage of the low voltage side, used to calculate the ratio error and deduce the tap position.
  • Tap Spacing: If there is no tap, any value can be set for this position.
  • Rated Tap: If there is no tap, please set 0 or 1.

After setting the parameters, click "TEST" or press the silicone button "TEST" to initiate the test. The test result will be displayed on the screen.

Single-phase test result interface

Image: Single-phase test result screen, showing Ratio, Angle, Error, and Tap.

6.2. Three-Phase Transformer Test Operation

For conventional three-phase transformers with a recognizable nameplate, click the "Three phase test" icon and then "Normal test" to enter the setup interface. If the nameplate is not recognizable, click "Three-phase test" and then "Three phase blind test" to enter the setup interface.

For Z-Type Transformers, if the nameplate is recognizable, click the "Z-Type Test" icon to enter the test setup interface.

Three-phase test setup interface

Image: Three-phase test setup screen, showing Sample, High, Low, Tap, and Group parameters.

  • Specimen No.: As with single-phase tests, this helps distinguish transformers and does not affect results.
  • Rated HV/Low Voltage: Used for ratio error calculation and tap position deduction.
  • Tap: The parameter on the left is tap spacing; the parameter on the right is the rated tap. Set to 0 or 1 if no tap.
  • LINK GROUP: Contains three parameters for high-voltage side coupling methods, including D, Y, YN, ZN. Unknown can be selected during three-phase blind testing.
  • Low-voltage side linkage: Includes d, y, yn, and optionally unknown for three-phase blind measurements.
  • Group: Transformer group, including 0, 11, and "Auto". Only "Auto" is available in three-phase blind test.

After setting parameters, click "TEST" or press the silicone button "TEST". The test result will be displayed.

Three-phase test result interface

Image: Three-phase test result screen, showing Ratio and Error for AB/ab, BC/bc, CA/ca, Group, and Tap.

6.3. Data Management

6.3.1. Data Storage

In the test result interface, click "Save" to save the test results. The tester can save 500 sets of test results. If storage is full, clear old records from the access screen before saving new data.

6.3.2. Data Access/Deletion

In the main interface, click the "View" icon to enter the access interface for data access and deletion. If no data is saved, the interface will prompt "No saved data!".

Press the left and right buttons to turn pages, and the up and down buttons to select the record you need to view. You can also directly click on a record on the large screen to view it.

Data access screen

Image: Data access screen, showing a list of saved test records with options to view or delete.

6.4. APP and PC Upper Computer Operation

This instrument supports connecting to Android APP and PC upper computer.

6.4.1. PC Upper Connection Instructions:

  1. Install the USB driver and host computer software from the provided CD ROM.
  2. After the instrument is switched on, use the instrument accessory USB cable. Connect one end to the USB port of the instrument and the other end to the USB port of the computer.
  3. Run the software on the computer. It will automatically search for the port and connect.
  4. After successful connection, you can check historical data, generate Excel reports, and perform other operations through the software.

6.4.2. Android APP Connection Instructions:

  1. Before using, ensure your mobile phone or tablet system version is Android 5.0 or above.
  2. Ensure the TTR Tester APP is installed on your intelligent device.
  3. In the "Settings" page, click the Bluetooth icon to turn on Bluetooth.
  4. Turn on the APP, search for the Bluetooth device with the name "TTR Tester", and connect to it.
  5. After successful connection, you can realize wireless control measurement and data browsing.

6.5. Product Demonstration Video

Video: A demonstration of the ES6030 Transformer Turns Ratio Tester's interface and basic operation, including setting parameters, running a test, saving data, and navigating settings.

7. Maintenance

7.1. Battery Level Check

After power on, if the upper right corner of the screen shows a low battery voltage symbol, it means the battery power is insufficient. Please charge it in time to ensure measurement accuracy.

The power consumption during the test is higher than standby. If the low battery voltage symbol appears during a test, the battery power is about to be insufficient. Please charge it promptly to ensure accuracy.

If the battery power is not enough to support the test, the device will automatically shut down. Please charge and then re-test.

7.2. Overload Protection

Every time before switching on and testing the resistance, the instrument will perform an overload check. If an overload is detected, it will carry out overload protection and prompt a warning. In such a case, please switch off the device and ensure that the test body is not charged before switching on and testing again.

After overload protection, disconnect the cable and restart the instrument to turn on normally.

8. Troubleshooting

If you encounter any issues not covered in this manual, please refer to the official user manual PDF or contact customer support.

User Manual (PDF) Reference: A detailed user manual in PDF format is available for further reference. You can access it at: ES6030 User Manual (PDF)

9. User Tips

  • When performing three-phase transformer tests, the ES6030 supports various connection types including star (Y) and delta (D) configurations, as well as YN and ZN. Ensure you select the correct group setting for accurate measurements.
  • For blind tests where the transformer nameplate is unknown, utilize the "Three phase blind test" option to determine the ratio and group.
  • Regularly check the battery level, especially before critical measurements, to avoid unexpected shutdowns and ensure consistent performance.

10. Packing List

The following items are included with your ES6030 Transformer Turns Ratio Tester:

ES6030 Packing List Contents

Image: Contents of the ES6030 packing list, including the tester, cables, manual, CD, charger, and carrying bag.

ItemQuantityDetails
Instrument1 pcsES6030 Transformer Turns Ratio Tester
Test line2 groupsRed and black, each 10 meters/group
CD1 pcsContains USB driver and host computer software
Data cable1 pcsType-C, 1 meter
Charger1 pcs14.8V/1.5A
Introduction manual, warranty, certification1 set
Parcel1 pcsCarrying bag

11. Warranty and Support

The contents of this user manual do not justify the use of the product for special purposes. The Company is not responsible for other damages caused by the use. The Company reserves the right to modify the contents of the user manual without further notice.

For support or inquiries, please contact:

Guangzhou Zhengneng Electronic Technology Co., Ltd.
Address: 4/F, No. 771, Guang Cong 8th Road, Changyao Ling Village, Zhongluotan Town, Baiyun District, Guangzhou, China
Tel: +86-13564525088
Email: harrybot@aliyun.com
Company website: www.fuzrr.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.