OBDOK Can K-line Immo Tool

Contents

OBDOK Can K-line Immo Tool V4.10 User Manual

Model: Can K-line Immo Tool | Brand: OBDOK

1. Introduction

The OBDOK Can K-line Immo Tool V4.10 is an advanced OBD2 diagnostic and programming device designed for Renault vehicles. It provides various functions for electronic control unit (ECU) internal memory modification, including reading/writing EEPROM or FLASH memory, clearing immobilizer codes, reading immobilizer status, and programming key cards. This tool operates via the OBD2 connector, eliminating the need to open the control unit or desolder memory ICs for most operations.

Important Note: The hardware for this tool is purchased, and the software is provided free of charge. While the Renault ECU Tool V4.10 software can be used, not all functions are fully developed for version 4.10. Versions 4.08 and 4.09 software are generally stable and can be used without problems, supporting most functions.

If you cannot accept the software limitations or development status, please do not purchase this product.

2. Product Overview

The OBDOK Can K-line Immo Tool consists of the main diagnostic interface unit and necessary connection cables. Below are visual representations and details of the device.

OBDOK Can K-line Immo Tool with USB and OBD2 cables

Figure 2.1: OBDOK Can K-line Immo Tool with included USB and OBD2 cables.

Video 2.1: A brief overview of the OBDOK Can K-line Immo Tool and its components.

2.1. Device Pinout

The device features a DB9 connector. The pinout details are crucial for proper connection, especially when connecting 'on the bench' using the Connection Manual.

Close-up of the OBDOK Can K-line Immo Tool label showing DB9 connector pinout

Figure 2.2: Close-up view of the device label detailing the DB9 connector pinout.

Table 2.1: DB9 Connector Pinout
Pin No.Function
1CAN H
2CAN L
3NC (Not Connected)
4K line
5GND (Ground)
6L line
7NC (Not Connected)
8NC (Not Connected)
9+12V

The device also indicates Tx (Transmit) and Rx (Receive) LEDs, and power inputs: +5V (USB) and +12V (OBD).

3. Setup Instructions

Follow these steps to set up your OBDOK Can K-line Immo Tool:

  1. Software Installation: Install the provided software (preferably V4.08 or V4.09 for full functionality) on your computer. Ensure your operating system meets the software requirements.
  2. Connect to Computer: Connect the OBDOK tool to your computer using the supplied USB cable. The device should power on via the +5V (USB) input.
  3. Connect to Vehicle/ECU:
    • Via OBD2 Connector: For in-vehicle operations, connect the OBD2 cable to the tool's DB9 port and then to the vehicle's OBD2 port. The device will receive +12V power from the vehicle's OBD port.
    • On the Bench: For bench operations, refer to the Connection Manual for specific wiring instructions based on the ECU type. Ensure correct pin connections for CAN H, CAN L, K-line, L-line, GND, and +12V power supply.
  4. Launch Software: Open the installed OBDOK software on your computer. The software should detect the connected tool.

4. Operating Instructions

The OBDOK Can K-line Immo Tool offers several key functions for Renault vehicles. Always ensure the vehicle's battery is adequately charged before performing any programming operations.

4.1. Read/Write EEPROM or FLASH

This function allows you to read and write data to the EEPROM or FLASH memory of supported ECUs. This is typically used for data backup, cloning, or modifying specific parameters.

  1. Connect the tool to the ECU (in-vehicle or on-bench) as described in the Setup section.
  2. Select the appropriate ECU type and memory area (EEPROM/FLASH) within the software.
  3. Choose the 'Read' option to extract data or 'Write' to program new data. Follow on-screen prompts.

4.2. Clear Immobilizer Code

The Clear Immobilizer Code function is fully automated. It clears previously memorized immobilizer codes, making the ECU ready to accept a new immobilizer code. This is useful for adapting second-hand ECUs to a particular car or for simple data cloning.

  1. Connect the tool to the ECU.
  2. Select the 'Clear Immobilizer Code' function in the software.
  3. Press the designated button in the software to initiate the clearing process. The control unit will be cleared, and no future programming is required for this specific step.

Note: This tool is NOT for total immobilizer disabling. It only clears previously memorized immobilizer codes to allow the use of second-hand ECUs or data cloning.

4.3. Key Card Programming

This function allows for programming new key cards for supported Renault models.

  1. Connect the tool to the vehicle's OBD2 port.
  2. Select the 'Key Card Programming' function in the software.
  3. Follow the software's step-by-step instructions to program new key cards. This may involve inserting keys, turning the ignition, or other vehicle-specific procedures.

5. Supported Vehicles and Functions

The OBDOK Can K-line Immo Tool supports a wide range of Renault ECUs and functions. Below is a detailed list:

  • ABS/ESP (ATE) for X91/X95/X38/L70: EEPROM R/W, Change VIN, Change KM by OBD2.
  • Automatic parking brake (TRW) for X95/X38: R/W Config, Change VIN, set maintenance mode for brake pad replacement (NEW!).
  • EDC17 / SID305-310 / DCM3.4 / EMS31XX: Mileage Repair by OBD II.
  • EDC15C3 (CAN-BUS and WIRE immo systems): R/W EEPROM, R/W FLASH, Clear Immo Code.
  • EDC15C13: R/W EEPROM, R/W FLASH, Clear Immo Code.
  • FOR SIRIUS 31H: R/W EEPROM, R/W FLASH, Clear Immo Code.
  • FOR SIRIUS 32[N] (CAN-BUS and WIRE immo systems): R/W EEPROM, R/W FLASH, Clear Immo Code.
  • FOR SIRIUS 34 (CAN-BUS and WIRE immo systems): R/W EEPROM, R/W FLASH, Clear Immo Code.
  • FOR SIRIUS 35: R/W EEPROM, R/W FLASH, Clear Immo Code.
  • EMS3132 (CAN-BUS and WIRE immo systems): R/W EEPROM, R/W FLASH, Clear Immo Code.
  • EMS3134 (CAN-BUS and WIRE immo systems): R/W EEPROM, R/W FLASH, Clear Immo Code.
  • SID301: R/W EEPROM, R/W FLASH, Clear Immo Code, Clear IMPACT DETECTED, Read stored mileage.
  • SIM32: R/W EEPROM, R/W FLASH from HD64F7055, Clear Immo Code.
  • SAFIR / SAFIR2 / SFR200 (35 / 55 pin connector): R TMS374 EEPROM, Clear Immo Code (car runs without immobilizer code).
  • IAW 6R.20: R/W TMS370 EEPROM.
  • IAW 6R.30: R TMS370 EEPROM, Clear Immo Code (car runs without immobilizer code).
  • for VALEO BII for ESPACE III: R/W (9)08AZ60 EEPROM, R/W mileage, Clear for Replacement, Read transponder data, Emergency Startup.
  • for VALEO IMMOBILIZER for LAGUNA I Ph2 (1998-2000): Read transponder data, Configure, Reset to VIR-GIN.
  • for VALEO IMMOBILIZER for LAGUNA I Ph1 / SAFRANE Ph1 (1995-1996): Read PINCODE, Reset to VIR-GIN.
  • for INSTRUMENT CLUSTER for ESPACE III (1998-2002): Reset odometer, Erase RF remote programming by instrument cluster connector.
  • Sie-mens IMMOBILIZER for ESPACE III Ph1 (1996-1998): R/W 68HC05B16 EEPROM, Read transponder data.
  • for INSTRUMENT CLUSTER for ESPACE IV Ph1 ('03-'04) K-Line: Change language and units, Change VIN, KM, R/W EEPROM.
  • for INSTRUMENT CLUSTER for ESPACE IV Ph2-Ph4 ('2005+) CAN: Change language and units, Change VIN, KM, R/W EEPROM.
  • Sie-mens UCH for MEGANE/SCENIC I Ph2 ('99-'02): R/W 705B32 EEPROM, R/W configuration, Learn Keys, Reset to VIR-GIN.
  • Sie-mens UCBIC for MEGANE/SCENIC I Ph1 ('96-'98): R/W 68HC05B16 EEPROM, R/W configuration, Reset to VIR-GIN.
  • for LAGUNA II, for ESPACE IV, VELSATIS Ph1/Ph2: Key-Card Programming, Change VIN, Reset UCH to VIR-GIN, Learn UCH.
  • for MEGANE II, SCENIC II Ph1/Ph2: Card/UCH/ECM/ESCL Learning, Change VIN, Reset UCH to VIR-GIN, Config TPMS.
  • INSTRUMENT CLUSTER for SCENIC II ('04-'08): Wake-Up by CAN-BUS for repair or to check mileage, Change language and units, Change VIN, KM, R/W EEPROM.
  • INSTRUMENT CLUSTER for MEGANE II ('03-'08): Wake-Up by CAN-BUS for repair or to check mileage, Change language and units, Change VIN, KM, R/W EEPROM.
  • for C-LIO II Ph1: Key Learning, Configuration, Reset BMT to VIR-GIN.
  • for C-LIO II Ph2-5, for KANGOO, for TRAFIC, for MASTER, for VIVARO, for MOVANO (-'07): R/W EEPROM 93C66, Key Learning, Change VIN, Reset UCH to VIR-GIN, Learn UCH.
  • for KANGOO I, for TRAFIC, MASTER, VIVARO, MOVANO ('07-): Key Learning, Change VIN, Reset UCH to VIR-GIN, Learn VIR-GIN UCH.
  • for KANGOO II (2007-2012): Key Programming, Change VIN, Reset BCM to VIR-GIN, Learn VIR-GIN BCM.
  • for MODUS / for C-LIO III ELECTRIC POWER ASSISTED STEERING (for TRW DAE/for PAS): Clear Immo Code, Change VIN by OBD2, erase DF002 from 24C16 dump, repair CRC.
  • for MEGANE/SCENIC III ELECTRIC POWER ASSISTED STEERING (for NSK DAE/for PAS): Clear Immo Code, Change VIN by OBD2.
  • for MEGANE/SCENIC IV (2016+) ELECTRIC POWER ASSISTED STEERING (for NSK DAE/PAS): Clear Immo Code, Change VIN by OBD2.
  • TWINGO III ELECTRIC POWER ASSISTED STEERING (for JTEKT DAE/PAS): Clear Immo Code, Change VIN by OBD2.
  • for ESPACE V / for TALISMAN / for SAMSUNG SM6 ELECTRIC POWER ASSISTED STEERING (for TRW EPS): Clear Immo Code, Change VIN by OBD2.
  • for C-LIO IV ELECTRIC POWER ASSISTED STEERING (for JTEKT DAE/PAS): Clear Immo Code, Change VIN by OBD2.
  • for LAGUNA III (2007-2015): KeyCard Programming, Change VIN, Reset BCM to VIR-GIN.
  • for LAGUNA III / LATITUDE (2007-2015): Learn BCM / ECM / ESCL in protected mode.
  • LATITUDE (2010+): KeyCard Programming, Change VIN, Reset BCM to VIR-GIN.
  • for C-LIO III / MODUS: Key Programming, Change VIN, Learn ECM in protected mode, Learn BCM, Reset BCM to VIR-GIN.
  • for C-LIO III: Card/UCH/ECM/ESCL Learning, Change VIN, Reset UCH to VIR-GIN.
  • for C-LIO IV (2012+): Card Programming, Change VIN, Reset HFM to VIR-GIN, Learn ECM / ESCL/HFM in protected mode.
  • MASTER III (2010-2014): Key Programming, Change VIN, Reset BCM to VIR-GIN, Learn VIR-GIN BCM.
  • for TRAFIC II Ph3 (2010-2014): Key Programming, Change VIN, Reset BCM to VIR-GIN, Learn VIR-GIN BCM.
  • for WIND (2010-2013): Key Programming, Change VIN, Reset BCM, Learn ECM, Learn BCM.
  • for TWINGO II (2007-2013): Key Programming, Change VIN, Reset BCM, Learn ECM, Learn BCM.
  • for TWINGO (2001-2006), for LOGAN (2004-2008), for SANDERO I, for THALIA, for SYMBOL: Key Programming, Change VIN.
  • for LOGAN, for SANDERO, for THALIA, for SYMBOL (2008-2012), for Duster (2010-2012): Key Programming, Change VIN.
  • for LOGAN, for SANDERO, for DOKKER, for SYMBOL, for DUSTER (2012+): Key/ECM/BCM learning, Reset to VIR-GIN, Read DataFLASH, Change VIN.
  • for MEGANE III / SCENIC III (2009-2015): Card Programming, Change VIN, Reset BCM to VIR-GIN.
  • for MEGANE III / SCENIC III (2009-2015): Classical Key Programming, Change VIN, Reset BCM to VIR-GIN.
  • for MEGANE III / SCENIC III / for FLUENCE (2009-2015): Learn BCM / ECM / ESCL in protected mode. Config TPMS.
  • for KOLEOS (2008+): KeyCard Programming, Change VIN, Reset BCM to VIR-GIN, Learn ECM/BCM/ESCL.
  • EDC17 / MED17 TRICORE EEPROM DUMP CRC: Reset EEPROM dump to VIR-GIN, repair block CRCs.
  • EDC17 / MED17 TRICORE TC1793 EEPROM DUMP CRC: Repair block CRCs.
  • EDC16 EEPROM DUMP CRC: Reset EEPROM dump to VIR-GIN, repair block CRCs (IMPROVED!).
  • DELPHI DCM 3.4 EEPROM DUMP CRC: Reset EEPROM dump to VIR-GIN, Change KM, repair block CRCs.
  • for DECRYPT ISK FROM ECM DUMP: Get ISK from ECM for VIR-GING BCM learning when original BCM is missing.
  • SID305/306/307/308/309 for TRICORE DFLA-SH DUMP CRC: Search/Change KM, repair block CRCs.
  • for MEGANE III / SCENIC III / FLUENCE / LATITUDE AIR-BAG (for CONTINENTAL): Erase CRASH DATA by OBD2 / direct connection.
  • for LAGUNA III AIR-BAG (AUTOLIV RC5): Erase CRASH DATA by OBD2 / direct connection.
  • TWINGO II (X44) / KANGOO II (X61) AIR-BAG (for CONTINENTAL): Erase CRASH DATA by OBD2 / direct connection.
  • MASTER III / for MOVANO-B / for C-LIO III Ph2 / for MODUS Ph2 AIR-BAG (for AUTOLIV): Erase CRASH DATA by OBD2 / direct connection.
  • AIR-BAG MODULE WITH SPC560 MCU (for CONTINENTAL): Erase CRASH DATA by OBD2 / direct connection.
  • for MEGANE II / SCENIC II AIR-BAG (for AUTOLIV ACU4): Erase CRASH DATA by OBD2 / direct connection.
  • for C-LIO II X65 AIR-BAG (for BOS-CH AB8): Erase CRASH DATA, R/W MCU internal EEPROM by OBD2 / direct connection.
  • for C-LIO III Ph1 / MODUS Ph1 AIR-BAG (for BOS-CH AB9.X): Erase CRASH DATA, Erase fault codes by OBD2 / direct connection.
  • for ESPACE III AIR-BAG (Sie-mens): Erase CRASH DATA, R/W MCU internal EEPROM by OBD2 / direct connection.
  • for LOGAN X90 / for DUSTER H79 AIR-BAG (TEMIC-for CONTINENTAL): Erase CRASH DATA, Read EEPROM by OBD2 / direct connection.
  • for LOGAN X90 AIR-BAG (for BOS-CH AB8.X with yellow connector): Erase CRASH DATA, R/W MCU internal EEPROM by OBD2 / direct connection.
  • for KADJAR / TALISMAN AIR-BAG (for AUTOLIV AC7 with MCU XC2336): Erase CRASH DATA by OBD2 / direct connection. Read full FLASH.
  • for C-LIO IV Ph2 / CAPTUR Ph2 AIR-BAG (for CONTINENTAL 985100475R, 985101180R, 985103419R with R7F7010133): Erase CRASH DATA by OBD2 / direct connection.

6. Maintenance

To ensure the longevity and optimal performance of your OBDOK Can K-line Immo Tool, follow these maintenance guidelines:

  • Storage: Store the device in a cool, dry place away from direct sunlight and extreme temperatures.
  • Cleaning: Use a soft, dry cloth to clean the device. Do not use harsh chemicals or abrasive cleaners.
  • Cable Care: Avoid bending or twisting the cables excessively. Store them neatly to prevent damage.
  • Software Updates: Regularly check for software updates from the manufacturer to ensure compatibility with newer vehicle models and to access the latest features.

7. Troubleshooting

If you encounter issues with your OBDOK Can K-line Immo Tool, try the following troubleshooting steps:

  • Device Not Powering On:
    • Ensure the USB cable is securely connected to both the device and the computer.
    • If connected to a vehicle, verify the OBD2 cable is properly seated and the vehicle's ignition is on (if required for power).
  • Software Not Detecting Device:
    • Check USB cable connection.
    • Reinstall device drivers if prompted by the operating system.
    • Try a different USB port on your computer.
  • Function Not Working as Expected:
    • Verify that the specific function is supported for your vehicle's ECU model and year.
    • Ensure you are using the recommended software version (V4.08 or V4.09 for broader compatibility).
    • Check all connections to the vehicle/ECU.
    • Consult the detailed Connection Manual for bench connections.
  • Communication Errors:
    • Ensure the vehicle's battery voltage is stable and sufficient.
    • Turn off any unnecessary electrical consumers in the vehicle.

8. Specifications

AttributeValue
Brand NameOBDOK
Model NameCan K-line Immo Tool
Hardware VersionV4.10
Software VersionV4.10
OriginMainland China
CertificationCE
External Testing Certificationce
Item Weight0.5kg
Is Batteries IncludedNo
Wireless FunctionNo
Wireless SupportNo
ElectronicNo
UseNot Telecommunication
High-concerned chemicalNone
Package Weight0.5 kg
Package Dimensions (L x W x H)15 cm x 20 cm x 10 cm

9. User Tips

Based on user feedback, consider the following tips for a better experience:

  • Verify Functionality: Before purchasing, it is highly recommended to contact the seller to confirm if the specific functions you intend to use are fully operational and supported for your vehicle model. Not all advertised functions may work as expected across all software versions or vehicle configurations.
  • Software Version: While V4.10 is the newest, older versions like V4.08 and V4.09 are often more stable and have broader functionality for many operations. Consider using these versions if you encounter issues with V4.10.
  • Connection Manual: For 'on the bench' connections, always refer to the detailed Connection Manual to ensure correct wiring and avoid damage to the ECU or the tool.

10. Warranty and Support

For any technical support, warranty claims, or inquiries regarding the OBDOK Can K-line Immo Tool, please refer to the official seller's support channels. A user manual in PDF format is available for further reference: View User Manual (PDF).

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.