1. Introduction
This manual provides detailed instructions for the safe and effective operation of your Baofeng UV26 Walkie Talkie. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage.
1.1 Product Overview
The Baofeng UV26 is a multi-band walkie talkie featuring GPS/APRS positioning, Bluetooth programming, recording capabilities, and Type-C charging. It offers a long-range communication solution with a 1.77-inch large screen and 1000 channel storage.

1.2 Package Contents
Upon unpacking, please verify that all the following items are included:
- 1 Radio body
- 1 Lithium-Ion battery pack
- 1 Antenna
- 1 Power Adapter
- 1 Programming Cable
- 1 Belt Clip
- 1 Wrist Belt
- 1 Instruction Manual (PDF available for download)

1.3 Key Features
- Frequency Range: FM 76-108 MHz (RX); AM 108-136MHz (RX); VHF 136-174MHz (TX&RX), 220-260MHz (TX&RX), UHF 350-390MHz (TX&RX), 400-520MHz (TX&RX). Transmission Frequencies vary by region (America, Canadian, European Union versions).
- Display: 1.77" TFT large screen with full keyboard and open menu operation.
- Scanning: VFO scan range setting, three scan recovery methods, channel scan, CTC/DCS scan, channel addition and removal.
- Channel Management: Built-in input method for editing channel names, 10 zones storage, up to 1000 named memory channels.
- Weather Reception: NOAA Weather Radio Channel Reception (North American countries only).
- Frequency Step: Selectable between 2.5K, 5.0K, 6.25K, 10.0K, 12.5K, 20.0K, 25.0K, 50.0K.
- Charging: Type-C direct charging and charging stand.
- Battery: High Capacity Lithium-Ion battery.
- Power Output: High or low power selectable.
- Functions: VOX (voice activated transmit), Broadcast FM radio receiver 78-108 MHz, Alarm function, Display illumination programmable via keypad, Dual watch / Dual reception, Function beep on the keyboard, One touch search frequency.
- Connectivity: Two (2) pins for Kenwood accessory port.
- Advanced Features: GPS positioning (location sharing and retrieval), Bluetooth APP application (read/write radio data), Black box function (recorded trajectory), 300 hours of real-time recording, real-time clock display.
2. Safety Information and Regulations
2.1 Regulations and Safety Warnings
This product complies with essential requirements of Directive 2014/53/EU and other relevant provisions (2006/66/EC, 2011/65/EU, (EU)2015/863, 2012/19/EU). It can operate under 2000m.
WARNING! European users must possess a valid Amateur Radio License for transmitting. Failure to comply may result in legal action. Refer to the EU specification guide 2014/53/EU. This information applies to EU countries only.
2.2 Compliance with RF Exposure Standards
The radio adheres to the following RF energy exposure standards:
- United States Federal Communications Commission (FCC); 47 CFR § 1.1307, 1.1310 and 2.1093
- American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015
- Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition
2.3 RF Exposure Compliance and Control Guidelines
To ensure compliance with occupational/controlled environmental exposure limits:
- Do not remove the RF Exposure Label.
- User awareness instructions should accompany the device when transferred.
2.4 Operating Instructions
- Transmit no more than 50% of the time. Press the Push-to-Talk (PTT) key to transmit; release to receive.
- Keep the radio at least 2.5cm away from your face. The antenna should be kept away from the face and eyes.
- When worn on the body, use an approved holder, holster, case, or body harness. Non-approved accessories may exceed FCC RF exposure limits.
- Use only approved antennas, batteries, and accessories to avoid exceeding FCC RF exposure guidelines.
- Contact your local dealer for optional accessories.
2.5 Precautions for Portable Terminals
Operating Prohibitions
- Do not operate in locations with fuels, chemicals, explosive atmospheres, or flammable materials unless using an approved Ex-protection model.
- Do not operate near blasting areas.
- Do not operate near medical or electronic equipment vulnerable to RF signals.
- Do not hold the product while driving.
- Do not operate where wireless communication equipment is prohibited.
Important Tips
- Do not use unauthorized or damaged accessories.
- Keep the product at least 2.5 centimeters from your body during transmission.
- Do not keep the product receiving at high volume for extended periods.
- Do not use this device if operational requirements are not met.
3. Battery Information
3.1 Charging the Battery Pack
The Li-ion battery pack is not charged at the factory; please charge it before first use. For new batteries or those stored for over 2 months, fully charge/discharge the battery two or three times to achieve optimal performance. Replace the battery pack if operating time significantly decreases after proper charging.
3.2 Charger Supplied
Use only the specified charger provided by Baofeng. Other chargers may cause explosion or personal injury. Charge the battery when the radio displays low battery with a red flashing lamp or voice prompt.
3.3 Use Caution with the Li-ion Battery
- Do not short the battery terminals or throw the battery into fire. Do not attempt to remove the casing.
- Charge the battery between 5℃-40℃ (40°F - 105°F). Charging outside this range may not fully charge the battery.
- Turn off the radio before inserting it into the charger to avoid interference with charging.
- Do not interrupt the charging cycle until the green light is on.
- Do not recharge a fully charged battery; this may shorten its life or damage it.
- Dry a damp battery or radio before charging to avoid damage.
3.4 Using the Type-C Charger
The Type-C port allows convenient charging of your Li-ion battery pack.
- Ensure your radio is turned OFF.
- Plug the Type-C cable into the battery's charging port and connect the other end to a wall power outlet.
- An empty battery will fully charge in approximately 6 hours.
- The battery indicator light illuminates to indicate charging status.
| Red LED | Green LED | Status |
|---|---|---|
| Flashing | Steady | Standby (charger empty) / Error (charger with radio) |
| Steady | Off | Charging |
| Off | Steady | Charge complete |
The radio should be turned OFF during the charge cycle.

3.5 Battery Maintenance
- Charge batteries only at normal room temperatures.
- Turn off the radio when charging a battery attached to it for faster charging.
- Do not unplug the charger or remove the battery/radio before charging is complete.
- Never charge a wet battery.
- Batteries wear out over time. If operating time shortens, consider a new battery.
- Battery performance is reduced in freezing temperatures. Keep a spare battery warm in cold environments.
- Clean battery contacts with a dry cloth if dust interferes with charging.
3.6 How to Store the Battery
- Store the battery at approximately 80% discharge.
- Keep it in a low-temperature and dry environment.
- Keep it away from hot places and direct sunlight.
- To prevent severe capacity degradation during long-term storage, cycle the battery at least every six months.
- Do not short circuit the battery terminals.
- Never attempt to remove the casing from the battery pack.
- Never store the battery in unsafe surroundings, as a short may cause an explosion.
- Do not put the battery in a hot environment or throw it into a fire, as it may cause an explosion.
4. Preparation and Installation
4.1 Installing / Removing the Battery
Installing the Battery Pack
- Position the battery pack over the back of the radio.
- Engage the battery pack into the radio until it is fully seated.
- Tighten the screws using a coin or similar object to secure the battery pack. Do not overtighten.
Removing the Battery Pack
- Loosen the screws on the back of the battery pack.
- Lift the bottom of the battery pack slightly.
- Pull the battery pack out of the radio housing.
4.2 Installing / Removing the Antenna
Installing the Antenna
Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
Removing the Antenna
Turn the antenna counter-clockwise to remove it.
4.3 Installing / Removing the Belt Clip
Installing the Belt Clip
Place the belt clip above the corresponding holes on the back of the radio and screw it into place clockwise with the two supplied screws.
Removing the Belt Clip
Unscrew counter-clockwise to remove the belt clip.
4.4 Installing Additional Speaker/Microphone (Optional)
Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.
5. Radio Overview
5.1 Key Analytic Graph

- Power / Volume knob
- LED Status Indicator
- PTT key
- MIC Input
- SK1- VOX/ Monitor key
- SK2 key – FM radios/Emergency key
- V/M-VFO/MR key
- A/B key
- MENU key
- Numeric keypad
- Antenna input
- GPS antenna
- Color LCD
- Speaker/Mic Jacks
- Speaker
- Up or Down navigation keys
- Exit Key
- Battery tightening screw
- Type-C charge port
- Type-C charge indicator
5.2 Status Indications
The top LED indicates the current radio status:
| LED Indication | What it Indicates |
|---|---|
| Constant Green | Receiving Signal |
| Constant Red | Transmitting signal |
| Flashes Green | Monitor mode/Scanning Receiving |
5.3 LCD Icon Summary
| Icon | Description |
|---|---|
| Battery level indicator | Battery level indicator |
| DTMF side tone | Make sure you can hear the DTMF side tone from the radio speaker, set to DT-ST, ANI-ST, DT+ANI. |
| D | Dual watch enabled |
| V | VOX enabled |
| Bluetooth symbol | Bluetooth frequency writing function activated |
| GNSS symbol | GNSS function enabled |
| Keypad lock symbol | Keypad lock enabled |
| ZONE01 | Indication of the current channel's region. Working in storage mode |
| VFO | In the current working VFO mode. Allow manual frequency input |
| A | A displays (upper section) and emission level indication |
| B | B displays (lower section) and emission level indication |
| Squelch Open/Close | Squelch Open/Close Indicator |
| H | Transmit power level indicator, According to Power High |
| M | The current transmission power is medium power (used in normal environments). |
| L | Transmit power level indicator, According to Power Low |
| D | DCS enabled |
| C | CTCSS enabled |
| + | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted higher in frequency than RX. |
| R | Enables access of repeaters in VFO/Frequency Mode. TX will be shifted lower in frequency than RX |
| T | Reverse function enabled |
| Confidential calling | Talkaround has been activated, off grid at the central turntable. The transmission frequency is equal to the receive frequency |
| N | The confidential calling feature is activated |
| Narrowband enabled |
5.4 Main Keypad Controls
- MENU Key: Activates the MENU, selects menu items, and confirms parameters. Press and hold to quickly enter GPS mode after activation.
- Up/Down Keys: Press for more than 2 seconds to rapidly move channels and frequencies upwards/downwards. In SCAN mode, moves scanning upwards/downwards.
- EXIT Key: Exits Menu and functions. Press and hold to activate frequency sweep.
Numeric Keypad
Used to input information or selections.
- * Key: Activates frequency reversal and talkaround functions when there is a frequency difference between reception and transmission. To enable/disable keypad lock, press and hold for about two seconds.
- 0 Key: Press and hold to activate NOAA weather forecast reception.
6. Basic Operations
6.1 Power On/Off
Turning the unit on
Rotate the Volume/Power knob clockwise until you hear a "click". The radio will audibly double beep and display a message or flash the LCD. If voice prompt is enabled, it will announce "frequency mode" or "channel mode".
Turning the unit off
Rotate the Volume/Power knob counter-clockwise all the way until you hear a "click". The unit is now off.
6.2 Adjusting the Volume
Rotate the Volume/Power knob clockwise to increase volume, counter-clockwise to decrease. Be careful not to turn it too far to avoid turning off the radio. Use the monitor function (SK1- VOX/ Monitor key) to adjust volume against un-squelched static.
6.3 Main Band/Sub Band Switch
In standby mode, press the [A/B] key to switch between the main frequency band and sub frequency bands. The highlighted band is main, dimmed is sub.
6.4 VFO/Channel Switch
Press the [V/M] key to switch between VFO (Frequency) and Channel (MR) display. In channel mode, the channel number is displayed. In frequency mode, "VFO" is displayed.
6.5 Frequency (VFO) Mode
In VFO mode, navigate up and down the band using the Up or Down keys. Each press increments/decrements frequency by the set step. You can also input frequencies directly via the numeric keypad with kilohertz accuracy.
Example: Entering 436.61250 MHz on display A
- In standby mode, press the [V/M] key to switch to VFO mode.
- Enter [4][3][6][6][1][2][5][0] on the numeric keypad.
WARNING! Transmitting on unauthorized frequencies is illegal. Listening is generally legal. Consult your local regulatory body for specific laws.
6.6 Channel (MR) Mode and Channel Selection
There are two modes: Frequency (VFO) and Channel (MR). Channel mode is more practical for everyday use, while VFO mode is useful for experimentation and programming channels. In Channel (MR) mode, navigate up and down channels using the Up or Down keys or the encoder. Press [V/M] key to switch to Channel mode.
6.7 Selecting a Bank
The radio supports up to 10 banks, each with a maximum of 100 channels. To select a bank:
Press the MENU key, go to Menu > Bank, press Up or Down to select a bank, then press MENU key to confirm. The regional alias will be displayed at the bottom of the screen.
6.8 Making a Call
NOTE: Press the A/B key to switch the main channel if two channels are displayed. In standby, press [V/M] to switch between VFO and MR mode.
Channel mode call
After selecting a channel, hold down the [PTT] key to initiate a call. Speak into the microphone with a normal tone. The red LED will be on during the call.
Frequency mode call
Press [V/M] to switch to frequency mode, input the working frequency, then press and hold the [PTT] key to transmit. Speak into the microphone with a normal tone. The red LED will be on during transmission.
Receive a call
Release the [PTT] key to answer. The green LED will be on when receiving a call.
NOTE: For best reception, keep the microphone 2.5 cm to 5 cm from your mouth during transmission.
6.9 Emergency Alert
The Emergency Alert feature signals group members for help.
To activate: Press and hold the [SK2] key for 3 seconds. The radio will emit a loud siren and the flashlight will flash.
To exit: Press the SK2 (FM radios/Emergency) key.
WARNING: Use the Emergency Alert feature only in actual emergencies.
6.10 FM Radio (FM)
The radio can listen to FM frequencies between 65-108MHz.
- In frequency or channel mode, press [SK2] key to turn on the radio.
- Select the desired radio frequency with the Up or Down keys or input the frequency. Press #z to automatically search for a radio station.
- Press [SK2] key to exit FM radio.
Note: While listening to FM, the radio will automatically switch to the A/B receiving signal frequency or channel mode for transmitting and receiving. It will switch back to FM radio mode when the signal disappears.
6.11 Monitor
In standby, press and hold the [SK1] key to enter Monitor mode. This function allows monitoring weak signals or signals with matched carrier but weak signaling. Release [SK1] to turn off speakers and return to standby. If no signal is present, pressing [SK1] will emit noise.
6.12 Keypad Lock
The radio features a keypad lock that locks all keys except the three side keys.
To enable or disable: Press and hold the * key for about two seconds.
You can also enable automatic keypad lock after ten seconds of inactivity via the menu.
6.13 Frequency Reversal and Talkaround
When there is a frequency difference between receiving and transmitting, the radio operates in relay mode.
A momentary press of the * key enables the reverse function. If you want to listen to the repeater's input frequency, press * key momentarily to reverse your transmit and receive frequencies. The channel attribute bar will display 'R'.
Press the * key again to switch to talkaround mode, where the receiving frequency equals the transmitting frequency. The channel attribute bar will display 'T'.
6.14 TX Repeaters Tone
Press [PTT] + [SK1] key to send a 1750Hz repeaters tone. This is useful for communications through repeaters. This function works even if the keypad lock is enabled.
6.15 One Touch Frequency Search
- The radio acts as a receiver. Press and hold the MENU key, and the screen will display "SEARCH SEARCH...".
- If the transmitter continues to transmit and the unit receives an effective (strongest and stable) frequency, the received frequency will be displayed. If a CTCSS or DCS is present, its value will be displayed; otherwise, "NONE" is displayed.
- Press the MENU key to save the Search frequency and CTCSS or DCS to the channel.
Note: During frequency Search, press the #z key to switch between UHF or VHF bands.

7. Advanced Features
7.1 Scanner
The radio has a built-in scanner for VHF and UHF bands. In VFO mode, it scans in steps according to your set frequency step. In Channel (MR) mode, it scans your channels.
To enable: Press and hold the #z key for about two seconds. Change scanning direction with Up or Down keys. Press and hold #z again to exit scanning mode.
7.1.1 Frequency Ranger
In frequency mode, the sweep range can be precisely set by inputting start and end values via the keyboard.
Example: To scan 144.000-146.000MHZ, enter 144146. To scan 430.000-440.000MHZ, enter 430440.
Note: For VFO frequency Ranger, see Menu>SCAN>Freq Ranger.
7.1.2 Scan Modes
The scanner has three modes of operation:
- Time Operation (TO): Scanner stops when a signal is detected, then resumes scanning after a factory preset timeout.
- Carrier Operation (CO): Scanner stops when a signal is detected, then resumes scanning after a factory preset time with no signal.
- Search Operation (SE): Scanner stops when a signal is detected. To resume scanning, press and hold the #z key again.
Note: For Scan mode, see Menu>SCAN>Scan Mode.
7.1.3 Scan Sub-Code (CTCSS/DCS)
To search for a CTCSS code:
- In VFO mode, enter a known frequency (e.g., 144.525).
- Press MENU key to enter menu>>Scan>>3 Scan Sub-Code.
- Press Up or Down to select CTCSS.
- Press MENU key to enter and scan CTCSS codes. When a valid code is scanned, it stays on that code and the speaker turns on.
- Press MENU key to store the scanned CTCSS code and exit. In standby, the 'C' icon will be displayed. Press and hold PTT to make a callback.
To search for a DCS code:
- In VFO mode, enter a known frequency (e.g., 144.525).
- Press MENU key to enter menu>>Scan>>3 Scan Sub-Code.
- Press Up or Down to select DCS.
- Press MENU key to enter and scan DCS codes. When a valid code is scanned, it stays on that code and the speaker turns on.
- Press MENU key to store the scanned DCS code and exit. In standby, the 'D' icon will be displayed. Press and hold PTT to make a callback.
7.1.4 Sub-Code Scan Storage
In MR or VFO mode, scanned CTCSS/DCS codes can be stored as TX CTCSS/DCS only, RX CTCSS/DCS only, or both (ALL).
To save CTCSS/DCS code scan settings:
- Press MENU key to enter menu >> SCAN >> 4 Scan Memory.
- Press MENU key to enter Scan Memory setting, and press Up or Down to select:
- ALL: Stores scanned CTCSS/DCS as both received and transmitted.
- DECODER: Stores scanned CTCSS/DCS as receiver RX CTC/DCS only.
- ENCODER: Stores scanned CTCSS/DCS as transmitted TX CTC/DCS only.
- Press MENU key to save settings and return to the previous menu.
Note: Only when a valid CTCSS/DCS code is scanned and stopped, press the MENU key to store the CTCSS/DCS code and replace the corresponding CTCSS/DCS code of the current channel or frequency.
7.2 Dual Watch
The radio features Dual Watch functionality (single receiver) to monitor two channels. It can lock the transmit frequency to one of the two channels it monitors.
Enabling or disabling Dual Watch mode
- Press MENU key to enter the main menu.
- Enter 5 on the numeric keypad to get to Radio Settings.
- Press MENU key to confirm, enter 16 on the numeric keypad to get to 16 Dual Watch.
- Press MENU key to select.
- Use Up or Down keys to select OFF or ON.
- Press MENU key to confirm.
- Press EXIT key to return to the previous menu.
When ON, the 'D' icon is displayed. To disable, repeat the steps and select "OFF"; the 'D' icon will disappear.
7.3 Manual Programming (Channels Memory)
Memory channels store commonly used frequencies. The radio has 10 zones, with a maximum of 100 channels per zone. Each channel can store: Receive and transmit frequencies, transmit power, group signaling information, bandwidth, ANI/PTT-ID settings, and a six-character alphanumeric identifier or channel name.
Frequency Mode vs. Channel Mode
In standby mode, press V/M key to switch between frequency (VFO) mode and channel (MR) mode. VFO mode is for temporary frequency assignment or quick field programming. Channel mode is for selecting preprogrammed channels.
Example 1: Programming a Channel Repeater Offset with CTCSS Tone
New memory in Channel 10: RX = 432.55000 MHz, TX = 437.55000 MHz (a +5 Offset), TX CTCSS tone 123.0
- Press MENU key to switch between menus.
- Press V/M key to set the radio to VFO mode (VFO icon displayed).
- [6] > [1][3] > [1][0] (Deletes Prior Data in channel 10)
- [6] > [4] > 123.0 (Selects desired RX encode tone 123 CTCSS)
- [6] > [6] > 123.0 (Selects desired TX encode tone 123 CTCSS)
- [6] > [1][0] > [0][0][5][0][0] (Enter the OFFSET frequency 5.00MHz)
- [6] > [1][1] > [+] (Selects the offset direction: plus offset)
- Enter RX frequency (e.g., 43255000)
- [6] > [1][2] > [1][0] (Enter the same channel 10)
Channel has been added. Press V/M key to return to MR mode.
Example 2: Programming a Simplex Channel with CTCSS Tone
New memory in Channel 10: RX = 432.6500 MHz, TX CTCSS tone 123.0
- Press MENU key to switch between menus.
- Press V/M key to set the radio to VFO mode (VFO icon displayed).
- [6] > [1][3] > [1][0] (Deletes Prior Data in channel 10)
- [6] > [4] > 123.0 (Selects desired RX encode tone 123 CTCSS)
- [6] > [6] > 123.0 (Selects desired TX encode tone 123 CTCSS)
- Enter RX frequency (e.g., 43265000)
- [6] > [1][2] > [1][0] (Enter the same channel 10)
Channel has been added. Press V/M key to return to MR mode.
7.4 Repeaters Programming
These instructions assume you know your repeater's transmit and receive frequencies and are authorized to use it.
- Press V/M key to set the transceiver to VFO mode (VFO icon displayed).
- Use the numeric keypad to enter the repeater's output (your receive) frequency.
- Press [6] > [1][0] to get the offset frequency.
- Use the numeric keypad to enter the specified frequency offset.
- Press MENU key to confirm and save.
- Press [6] > [1][1] to get the offset direction.
- Use Up or Down keys to select plus (positive) or minus (negative) offset.
- Press MENU key to confirm and save.
- Optional: Save to memory (see "Manual programming"), Set up CTCSS (see "CTCSS").
- Press EXIT key to exit the menu. If successful, you should be able to make a test call through the repeater.
NOTE: If you experience problems, check settings or the procedure again. Some Amateur Radio repeaters (especially in Europe) use a 1750Hz tone burst. If still unable to connect, contact the radio system administrator or your local amateur radio club.
7.5 Bluetooth Write Frequency
You can read and write frequencies via Bluetooth. An APP program must be installed before performing Bluetooth read/write frequency operations.
Operation:
- Press MENU + [3] to enter Bluetooth.
- Press Up or Down keys to select "ON". The screen will display the Bluetooth icon.

7.6 Recording Function
This optional feature requires hardware support. You can view, play, or delete records through the record menu.
Records List
Set path: MENU + [7] + MENU to enter the Records List.
Press Up or Down key to view records entries. During viewing, press MENU to play records.
In records entries, TX represents transmitted records, RX represents received records. Records in VFO mode show transmission frequency; records in channel mode (MR mode) show channel name.
More records management can be achieved through the "Other Tools - Records" section of the CPS program software.
7.7 GPS Function
This optional feature requires hardware support. The position system is a typical DTMF calling application. Refer to "Signaling Calls" for setting call codes, names, and IDs.
Radios sending/receiving GPS location information must operate on the same frequency/channel and be set to the main frequency band.
In GPS mode, you can only view location information and cannot make normal calls. Exit GPS mode for voice intercom.
You can set system time, GPS on/off, time zone, and GPS mode through the position system menu. Press and hold MENU key to view, share, and request location information.

Date and time settings
Set path: MENU + 4 + MENU + 1: Enter hours and minutes, year, month, day. Once GPS position is successful, the system automatically synchronizes and updates the system time.
GPS on/off settings
Set path: MENU + 4 + MENU + 2: Press Up or Down key to select whether to turn GPS on/off. After turning on the position system, the screen displays the GPS icon.
Time zone settings
Set path: MENU + 4 + MENU + 3: Press Up or Down key to select the correct time zone.
GPS mode settings
This machine is equipped with a multi-mode GPS module, including GPS from the United States and Beidou from China.
Set path: MENU + 4 + MENU + 4: Press Up or Down key to select GPS mode (Beidou, GPS, or GPS+Beidou).
Use of GPS
In standby mode, press and hold MENU key to enter GPS mode and display "My Place" as an information list. Press MENU key to switch My Place in the information list mode or electronic compass mode. Press Up or Down key to switch the information of the selected member. The current member sequence will be displayed at the top of the interface.
Find My Place
- Press and hold MENU key to enter GPS mode.
- Use the Up or Down key to switch to "My Place".
- The GPS is in receive mode and displays "Searching...". The GPS character on the right is red, indicating positioning has not been successful. Note: If "Searching..." is displayed for a long time, search for satellites in an open location.
- "Searching Successful" indicates successful positioning, displaying current time, longitude, latitude, and altitude. N is north latitude, E is east longitude, H is height. The GPS character on the right is green.
Share My Place information (send to others)
- After successful GPS positioning, press MENU key to switch to the location information interface.
- Press Up or Down key to select the pre-programmed member sequence (01-20) and display the member sequence and name. Select the member sequence labeled as "native".
- Press the [PTT] key to share the current location information with group members.
Requesting someone else's place
- After successful GPS positioning, press MENU key to switch to the My Place information interface.
- Press Up or Down key to select the pre-programmed member sequence (01-20) and display the sequence and call name. Select member sequences not marked as "native".
- Press the [PTT] key to initiate a position request command to the target member.
Transmission is disabled during reception waiting. If the other party receives your request, they will reply with their location information. The red center point represents your position, the flashing red dot represents the other side's position, and the bottom left corner shows the reference distance between two radios.
9. Troubleshooting Guide
This section provides solutions to common issues. If problems persist, contact your dealer for technical support.
| Phenomena | Analysis | Solution |
|---|---|---|
| You cannot turn on the radio. | Battery improperly installed, low power, or dirty/damaged contacts. | Remove/reattach battery, recharge/replace battery, clean contacts. |
| During receiving, voice is weak or intermittent. | Low battery voltage, low volume, loose/incorrect antenna, blocked speaker. | Recharge/replace battery, increase volume, reattach antenna, clean speaker. |
| Cannot communicate with other group members. | Inconsistent frequency/signaling type, too far from others. | Verify TX/RX frequency/signaling type, move towards other members. |
| You hear unknown voices or noise. | Interrupted by radios on same frequency, analog mode without signaling. | Change frequency/adjust squelch, request dealer to set signaling. |
| Unable to hear anyone due to too much noise/hiss. | Too far from others, unfavorable position (blocked by buildings/underground), external disturbance. | Move towards other members, move to open/flat area, restart radio, try again, stay away from interference. |
| The radio keeps transmitting. | VOX turned on, headset not installed correctly. | Turn off VOX, check headset. |
10. Technical Specifications
Note: All specifications may be modified without prior notice or liability.
| GENERAL | |
|---|---|
| Channel Capacity | 1000/10 Bank |
| Channel Spacing | 25.0 KHz/12.5 KHz |
| Input Voltage | 7.4 VDC |
| Battery Life | Li-on: 15 hours @ 5 watts (5% TX, 5% RX, 90% Standby) |
| Operating temperature | -10°C to 60°C |
| Antenna Impedance | 50Ω |
| Radio Dimensions | 137mm X 65mm X 39mm (not including antenna) |
| Radio Weight | 310 g (with Li-ON battery) |
| TRANSMITTER | |
| Frequency Range (TX) | 144 to 148 MHz, 420 to 450 MHz (America version) 144 to 148 MHz, 430 to 450MHz (Canadian version) 144 to 146 MHz, 430 to 440MHz (European Union version)* |
| Modulation | 16K0F3E/11K0F3E |
| Spurious Emission | -16 dBm<1GHz, -16 dBm>1GHz |
| Frequency Stability | ±2.5 ppm |
| Audio Distortion | ≤5% |
| FM Hum & Noise | 40 dB |
| RECEIVER | |
| Frequency Range | FM76-108MHz; AM108-136MHz; VHF: 136-174 MHz; 220-260MHz; UHF:350-390MHz; 400- 600 MHz; |
| Sensitivity: 12 dB SINAD | -120 dBm |
| Adjacent Channel Selectivity | -60 dBm |
| Intermodulation and Rejection | -70 dBm |
| Rated Audio Power Output | 0.75 Watts @ 16 Ω |
| Rated Audio Distortion | ≤5% |
11. User Tips
- Battery Care: If your battery becomes wet, remove it from the radio, wipe it dry with a towel, and place it in a plastic bag with dry rice overnight to absorb moisture. This method is effective for minor splashes.
- Programming Software: While the radio supports Bluetooth APP programming, many users prefer computer-based software for more advanced configuration. Check the manufacturer's official website for available PC programming software and drivers.
- Bluetooth Setup: Remember to install the required APP program on your mobile device before attempting to read or write radio data via Bluetooth.
- GPS Positioning: For optimal GPS signal reception, ensure you are in an open location when trying to acquire a position fix.
12. Warranty and Support
12.1 EU Declaration of Conformity
Baofeng and Pofung declare that this radio equipment complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at http://www.pofung.cn/download.asp?EnBigClassName=EU%20DOC. For support, contact your local Baofeng helpdesk, dealer, or email wangjianhui@baofengradio.com.
12.2 Disclaimer
The accuracy and completeness of this manual's contents are diligently compiled. However, due to continuous technological development, the design and specifications of the product may change without prior notice. No part of this handbook may be copied, modified, translated, or disseminated without prior written authorization.
12.3 Contact Information
EU Contact: APEX CE SPECIALISTS LIMITED
Unit 3D North Point House, north Point Business Park,
New Mallow Road, Cork, T23 AT2P, Ireland
PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED
ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong
E-mail: wangjianhui@baofengradio.com
Website: Http://www.baofengradio.com