Hobbywing XRotor F7 FC

Contents

Hobbywing XRotor F7 Flight Controller and ESC Stack User Manual

Model: XRotor F7 Flight Controller, XRotor 55A 4-in-1 ESC, XRotor 65A 4-in-1 ESC

1. Introduction

This manual provides detailed instructions for the Hobbywing XRotor F7 Flight Controller and its compatible 55A and 65A 4-in-1 ESC stacks. Designed for FPV drones, these components offer high performance and reliability. Please read this manual thoroughly before installation and operation to ensure proper functionality and safety.

Video: Overview of Hobbywing FC & ESC Stack, showing different sizes and compatibility with various FPV drone motors.

2. Safety Precautions

  • Always disconnect the battery before performing any installation, maintenance, or repair work.
  • Ensure correct polarity when connecting power. Incorrect connections can cause severe damage.
  • Avoid short circuits. Double-check all connections before applying power.
  • Keep components away from moisture, dust, and extreme temperatures.
  • Handle with care to prevent damage to sensitive electronic components.
  • Do not attempt to modify the firmware unless you are experienced and understand the risks. Incorrect firmware flashing can render the device inoperable.

3. Package Contents

Depending on your purchase, your package may include the following components:

  • Hobbywing XRotor F7 Flight Controller
  • Hobbywing XRotor 55A 4-in-1 ESC (Optional)
  • Hobbywing XRotor 65A 4-in-1 ESC (Optional)
  • Connecting Cables (various types for FC to ESC, etc.)
  • Electrolytic Capacitor (for ESC)
  • Mounting Hardware (e.g., rubber grommets, screws)
Overview of Hobbywing XRotor F7 FC, 65A ESC, and 55A ESC

Image: Overview of the F7 Flight Controller, 65A ESC, and 55A ESC components.

Hobbywing XRotor F7 Flight Controller with connecting cable

Image: F7 Flight Controller with its connecting cable.

Hobbywing XRotor 55A ESC Stack with capacitor and wires

Image: 55A ESC Stack, including a capacitor and power wires.

Hobbywing XRotor 65A ESC Stack with capacitor and wires

Image: 65A ESC Stack, including a capacitor and power wires.

4. Specifications

4.1. F7 Flight Controller (F7-FC-Lite)

Parameter Value
Product NameF7-FC-Lite
Input Voltage4-6S LiPo
BEC5V@3A & 10V@3A
Size37*37*8mm
Weight8g
Mounting Hole30.5x30.5mm, M3
Support FC FirmwareBetaflight
Firmware NameHOBBYWING_XROTORF7CONV

4.2. XRotor 55A 4-in-1 ESC (XRotor-55A-4in1-Lite-AT-RTF)

Parameter Value
Input Voltage4-6S LiPo
Continuous Current55A * 4
Peak Current70A * 4
BECNone
Firmware 1 (Default)Self-developed firmware based on BLHeli_S Ver. 16.7
Firmware 2Self-developed firmware based on Bluejay
ConfiguratorBLHeliSuite 16.x or Bluejay configurator
ESC/Throttle Protocol (Firmware 1)Dshot150/300/600, PWM, Oneshot125/42, Multishot
ESC/Throttle Protocol (Firmware 2)(Bidirectional) Dshot150/300/600
Dimension44mm × 42mm × 5.86mm
Weight15g
Mounting Hole30.5 × 30.5mm, M3
Dimension and Interface Definition Diagram for 55A ESC

Image: Dimension and Interface Definition Diagram for the 55A ESC.

4.3. XRotor 65A 4-in-1 ESC (XRotor-65A-4in1-Lite-BLS-RTF)

Parameter Value
Input Voltage4-6S LiPo
Continuous Current65A * 4
Peak Current80A * 4
BECNone
Firmware 1 (Default)Self-developed firmware based on BLHeli_S Ver. 16.7
Firmware 2Self-developed firmware based on Bluejay
ConfiguratorBLHeliSuite 16.x or Bluejay configurator
ESC/Throttle Protocol (Firmware 1)Dshot150/300/600, PWM, Oneshot125/42, Multishot
ESC/Throttle Protocol (Firmware 2)(Bidirectional) Dshot150/300/600
Dimension44mm × 42mm × 5.86mm
Weight15g
Mounting Hole30.5 × 30.5mm, M3
Dimension and Interface Definition Diagram for 65A ESC

Image: Dimension and Interface Definition Diagram for the 65A ESC.

5. Setup

5.1. Mounting

Both the F7 Flight Controller and the 4-in-1 ESCs feature a 30.5x30.5mm mounting hole pattern with M3 screw compatibility. Use the provided rubber grommets to isolate vibrations. Ensure proper orientation as indicated by arrows or markings on the boards.

5.2. Wiring Connections

Refer to the diagrams below for proper connection of the Flight Controller to the ESC, receiver, VTX, camera, GPS, and other peripherals.

Device Connection Diagram for F7 Flight Controller

Image: Device Connection Diagram for the F7 Flight Controller, showing connections for receiver, VTX, camera, GPS, and buzzer.

Interface Pinout Descriptions:

  • VBAT+: Voltage monitoring / FC on board BEC powered port. In general, it's directly connected to the battery's "Positive" pole.
  • CRT: Current Sensor in port. It's connected to the current signal output port of the external voltmeter (at this point, please set the scale value for current monitoring on the FC software as per the voltmeter's instructions.).
  • GND: Ground, universal for all components.
  • S1/S2/S3/S4: Throttle signal output ports. S1 for ESC#1, S2 for ESC#2, S3 for ESC#3 and S4 for ESC#4.
  • TELEMETRY: UART6-TX, receive 4in1 ESC telemetry data.
  • RSSI: RSSI signal input.
  • 5V: 5V BEC output.
  • 3.3V: 3.3V output (it will be available only if the FC inputs the voltage of 5V first).
  • TX1/RX1: TX1 UART serial port.
  • SCL, SDA: I2C clock and data port, it can connect GPS/Magnetic compass with TX4, RX4.
  • VOUT: Video output port of the on-board OSD video signals.
  • 10V: 10V BEC output.
  • TX5/UART5-TX: Can be used for VTX Control (IRC/SA).
  • CA1, CA2: Camera control input video signal for on-board OSD. (Default CA1)
  • CTL: LED Camera Control.
  • Buzzer+ & Buzzer-: For connecting the buzzer's "Positive/Negative" poles.
  • LED-STRIP: LED output control signals to control the WS2812B LED strip.
  • Type-C: Type-C port. For connect PC.
  • Boot: Bootloader button.

5.3. ESC Features and Protection

The ESCs are compact and lightweight, weighing only 15g. They feature outstanding current endurance, with continuous current reaching 55A or 65A and peak current reaching 70A or 80A respectively. An onboard galvanometer is included.

The board features 18 high-quality 50V 10uF SMD filtering and energy storage capacitors. These, along with a standard 35V 680uF high-frequency, low-ESR electrolytic capacitor, effectively filter out signal interference from the power supply to the flight controller's gyroscope, ensuring smoother flight performance.

Detail of 18 onboard capacitors and 680uF electrolytic capacitor for upgraded ESC protection

Image: Close-up view of the 18 onboard capacitors and the 680uF electrolytic capacitor for enhanced ESC protection.

5.4. Firmware Information

The ESCs come with self-developed firmware based on BLHeli_S (Ver. 16.7) or Bluejay, supporting various protocols like Dshot150/300/600, PWM, Oneshot125/42, and Multishot. The F7 Flight Controller supports Betaflight firmware.

Important: You cannot flash or replace ESC firmware by yourself. If you need to use bidirectional Dshot or switch to Firmware 2, please contact sales before placing an order.

5.5. Black Box Storage

The F7 Flight Controller includes an onboard 16MB memory chip for recording flight logs, allowing you to analyze and optimize your flight performance.

Detail of onboard flash chip for black box storage

Image: Close-up view of the onboard flash chip for black box flight log storage.

5.6. Motor Output

The ESCs provide 6 motor outputs, suitable for building Quadcopter, Y6, or Fixed-wing drones. The motor pads S1-S4 and S5-S6 are clearly marked.

Motor output pads for Quadcopter/Y6/Fixed-wings

Image: Diagram showing the motor output pads (S1-S4 and S5-S6) on the ESC for various drone configurations.

6. Operating Instructions

6.1. Initial Configuration (Betaflight)

  • Connect the F7 Flight Controller to your computer via the Type-C USB port.
  • Open the Betaflight Configurator software.
  • Ensure the correct COM port is selected and click 'Connect'.
  • Navigate through the tabs (Ports, Configuration, PID Tuning, Motors, etc.) to set up your drone according to your frame, motors, and preferences.
  • Perform sensor calibration (accelerometer, gyroscope) as instructed in Betaflight.
  • Configure your receiver, modes (Arm, Angle, Acro, etc.), and OSD settings.
  • Save and Reboot after making changes.

For detailed Betaflight setup, refer to the official Betaflight documentation: https://betaflight.com/

6.2. ESC Operation

The ESCs are pre-flashed with firmware. After connecting to the FC, ensure your motor direction is correct. This can typically be adjusted in the Betaflight Motors tab or via the BLHeliSuite/Bluejay configurator if supported for your specific ESC firmware version (refer to specifications for compatibility).

6.3. Onboard Pit Switch Module

The F7 Flight Controller features an onboard Pit Switch Module. This allows for convenient control of your VTX power, typically used to power down the VTX during setup or waiting periods to prevent overheating and interference with other pilots. Configuration for this feature is usually done within Betaflight's Modes tab or CLI commands.

6.4. Dual BEC Output

The F7 FC provides dual BEC outputs: 5V@3A and 10V@3A. These can be used to power various peripherals such as your receiver, VTX, camera, GPS, and LEDs. Ensure that the current draw of your peripherals does not exceed the BEC's capacity.

7. Maintenance

  • Regularly inspect all solder joints and connections for any signs of wear, corrosion, or damage.
  • Keep the boards clean from dust, dirt, and debris. Use compressed air or a soft brush for cleaning.
  • Avoid exposing the electronics to direct sunlight or high temperatures for extended periods.
  • Periodically check for updated Betaflight firmware for the FC and consult the seller for any recommended ESC firmware updates.
  • Ensure the electrolytic capacitor is securely attached and not damaged.

8. Troubleshooting

  • No Power/No Lights: Check battery connection, ensure correct polarity. Inspect power cables for damage.
  • FC Not Connecting to Betaflight: Ensure correct drivers are installed. Try a different USB cable or port. Press the BOOT button while plugging in the USB if necessary to enter DFU mode for flashing.
  • Motors Not Spinning: Check motor connections to the ESC. Verify motor protocol settings in Betaflight. Ensure ESCs are armed (usually by setting an ARM switch in Betaflight). Check for any error messages in Betaflight.
  • Unstable Flight: Re-calibrate accelerometers. Check PID settings. Inspect propellers for damage or imbalance. Ensure mounting is secure and vibration-isolated.
  • Video Issues (FPV): Check VTX and camera connections. Verify VTX power output (using Pit Switch if applicable). Ensure antenna is securely attached.

9. User Tips

  • Always perform a dry run (without propellers) after any changes to ensure motors spin correctly and in the right direction.
  • Utilize the onboard 16MB black box storage to log flights and analyze performance for tuning and troubleshooting.
  • Keep your Betaflight firmware updated for the latest features and bug fixes.

10. Warranty & Support

For warranty claims, technical support, or specific inquiries regarding firmware updates for the ESCs, please contact your original point of purchase or the Hobbywing customer service directly.

Additional resources:

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.