Mankerlight E05II Ti

Contents

Manker E05II Ti 14500/AA EDC Flashlight User Manual

Model: E05II Ti

1. Introduction

The Mankerlight E05II Ti is a powerful and ultra-compact Every Day Carry (EDC) flashlight crafted from titanium. It offers exceptional illumination with a 105° wide beam angle and is designed for versatility, supporting multiple battery types. This manual provides essential information for the safe and effective use of your flashlight.

Key Features:

  • Gen 2 Model with full titanium shell and unique bead blast finish.
  • Solid copper "pill" housing the LED's copper MCPCB and driver.
  • Titanium plated 304 stainless steel deep carry clip.
  • Multi-fuel design: Compatible with 14500 li-ion, Ni-MH AA, and Alkaline AA batteries.
  • Extreme performance with up to 1300 lumens illumination and dual constant current drivers.
  • Forward 'clicky' button control for one-handed operation.
  • IP68 waterproof rated (2 meters underwater) and 1.5 meters drop-resistant.
  • Features a tritium slot at the tail switch.

2. Package Contents

Please check the box for the following items:

  • 1x Mankerlight E05II Titanium LED Flashlight
  • 1x Mankerlight 920 mAh protected 14500 lithium battery with Type-C USB port
  • 1x Type-C USB charging cable
  • 1x Lanyard
  • 1x Spare waterproof O-ring
  • 1x User manual (this document)
Diagram showing the contents of the E05-II Titanium package: flashlight, 14500 li-ion battery, Type-C USB charging cable, lanyard, spare waterproof O-ring, and user manual.
E05-II Titanium Package Content

3. Setup and Battery Installation

Important: The insulation tab inside the new battery compartment MUST be removed before installing batteries.

3.1. Installation Steps

  1. Open the Battery Compartment: Rotate the tail cap (or head) counterclockwise to unscrew it.
  2. Remove the Insulation Tab: Take out the batteries (if included), locate and remove the colored plastic insulation tab. This step is MANDATORY!
  3. Install Batteries Correctly: Check the polarity symbols inside the tube. Usually, the battery positive (+) end faces the head, and the negative (-) end faces the tail cap.
  4. Reassemble: After inserting batteries, align and screw the tail cap back on clockwise until snug (do not over-tighten).
Diagram illustrating the parts of the E05-II Titanium flashlight, including the flashlight head, body, orange peel aluminum reflector, deep carry pocket clip, lanyard hole, tritium slot, and forward 'clicky' button.
E05-II Titanium Brief Introduction (Parts Diagram)

4. Operation Guide

4.1. ON/OFF

  • Twist Switch: Tighten the head or tail cap fully to turn ON; loosen about half a turn counterclockwise to turn OFF.
  • Tail Click Switch: Press the tail button to turn ON/OFF. A light press may be momentary ON; a full click locks it ON.
  • Side Switch: Press the electronic switch on the body.

4.2. Mode Switching

  • Output Change ①: Continuously half-press the switch (interval more than 0.5 second) to change different outputs (Low - Medium - High). Full press to lock out the selected output.
  • Output Change ②: From OFF status, fully press the switch to turn on Low output, then fully press to turn OFF. Fully press again to turn on Med. output, then fully press to turn OFF. Fully press again to turn on High output, then fully press to turn OFF. If you keep fully pressing again, it will turn back to Low output.
  • Memory Function: When the light is OFF for 2 seconds, a full press will output the last used mode (except Strobe).
  • Strobe: Quickly double half-press the switch from OFF.

Note: When battery voltage is low, the light will step down directly to low output. Sometimes, if you turn off the light and then turn on again, it can be lighted up but will also step down to low output soon. When battery voltage is extremely low, the light will shut OFF automatically.

5. Battery Charging (for 14500 Li-ion Battery)

Your E05II Ti comes with a Mankerlight 920mAh 14500 li-ion battery featuring a built-in Type-C USB charging port.

  • The 14500 battery supports fast charging via USB-C chargers (such as QC, PD) and also works with USB-C to USB-C charging cables.
  • Charging Indicator: Plug the USB Type-C socket of the included charging cable into the USB-C port of the 14500 battery, and connect the other USB socket to an adapter. The battery has a built-in intelligent identified charging function. When charging, the indicator will be red. Once charging is complete, the indicator will change to green.
  • Fully Charging Time: Approximately 2 hours via a universal charging adapter.

6. Maintenance

  • Cleaning: Clean the lens and body with a soft, dry cloth. Avoid using corrosive chemicals.
  • O-rings: Ensure O-rings are clean and properly seated to maintain water resistance. Periodically lubricate O-rings with silicone grease.
  • Battery Storage: If the flashlight will not be used for a long time, remove the batteries and store them separately. For lithium-ion batteries, charge them at least once every 2-3 months to prevent self-discharge.

7. Troubleshooting

7.1. No Light

  • Insulation tab not removed: Ensure the colored plastic insulation tab has been removed from the battery compartment.
  • Batteries reversed: Check battery polarity and reinstall correctly.
  • Batteries exhausted: Replace with new or fully charged batteries.
  • Parts not tightened securely: Ensure the tail cap and head are fully tightened.

7.2. Dim or Flickering Light

  • Weak batteries: Replace with new or fully charged batteries.
  • Switch mechanism/circuit issue: Check the switch mechanism/circuit, or reinstall batteries.
  • Slight Glow from Tail: This is a characteristic of some electronic switch circuits and not a defect. Loosening the tail cap slightly may stop it.

8. Specifications

Diagram showing the dimensions of the E05-II Titanium flashlight: 91.35mm (length) x 17mm (min body dia.) x 20mm (tail dia.), with a weight of 79.3g / 2.79oz (with battery).
E05-II Titanium Size and Weight
FeatureDetail
Light Source1x 6500K cool white LED emitter or Nichia 519A 4000K R9080
Light ModesLow - Medium - High + Strobe
Battery Compatibility1x 14500 li-ion / 1x Alkaline AA / 1x Ni-MH AA
Working Voltage0.9 V - 4.2 V
DriverHigh efficiency constant current circuit (both 14500 and AA)
Body MaterialTitanium with bead blasted finish
Clip Type / MaterialDeep carry clip / 304 stainless steel with titanium plated
Button MaterialTitanium with bead blasted finish
LensDual-sided AR coated, 99% transmittance toughened Glass
OpticOrange peel aluminum reflector with vacuum plated
Switch TypeForward-click button (mechanical switch)
Tritium Slot1 slot in button cap (fits 6*1.5 mm)
Size91.35mm (length) x Ø17mm (min body dia.) x Ø20mm (tail dia.) / 3.60" x 0.67" x 0.79"
Weight79.3 g / 2.79 oz (included 14500 battery)
Impact Resistance1.5 meters
WaterproofIP68 rated, tested 2 meters underwater for 60 minutes

8.1. Performance Data (6500K Cool White LED)

Powered by Mankerlight 14500 USB-C Li-ion Battery:

  • Low: 8 lumens, 50 hours
  • Medium: 300 lumens ~ 8 lumens, 1 hr 30 min + 3 hrs 50 min
  • High: 1,300 lumens ~ 300 lumens ~ 8 lumens, 2 min + 1 hr + 4 hrs
  • Strobe: 1,300 lumens, 20Hz
  • Beam Intensity: 5,476 cd
  • Beam Distance: 148 meters

Powered by AA Ni-MH Battery:

  • Low: 1.5 lumens, 27 hours
  • Medium: 100 lumens ~ 1.5 lumens, 1 hr 50 min + 3 hrs 3 min
  • High: 420 lumens ~ 100 lumens ~ 1.5 lumens, 2 min + 2 hrs + 30 min
  • Strobe: 420 lumens, 20Hz
  • Beam Intensity: 1,806 cd
  • Beam Distance: 85 meters

Powered by AA Alkaline Battery:

  • Low: 1.5 lumens, 55 hours
  • Medium: 100 lumens ~ 1.5 lumens, 1 hr 20 min + 16 hrs 50 min
  • High: 420 lumens ~ 100 lumens ~ 1.5 lumens, 1 min + 48 min + 3 hrs 15 min
  • Strobe: 420 lumens, 20Hz
  • Beam Intensity: 1,806 cd
  • Beam Distance: 85 meters

8.2. Performance Data (Nichia 519A 4000K R9080 LED)

Powered by Mankerlight 14500 USB-C Li-ion Battery:

  • Low: 6.5 lumens, 50 hours
  • Medium: 220 lumens ~ 6.5 lumens, 1 hr 30 min + 3 hrs 50 min
  • High: 800 lumens ~ 220 lumens ~ 6.5 lumens, 2 min + 1 hr + 4 hrs
  • Strobe: 800 lumens, 20Hz
  • Beam Intensity: 3,600 cd
  • Beam Distance: 120 meters

Powered by AA Ni-MH Battery:

  • Low: 1.5 lumens, 27 hours
  • Medium: 80 lumens ~ 1.5 lumens, 1 hr 50 min + 3 hrs 3 min
  • High: 300 lumens ~ 80 lumens ~ 1.5 lumens, 2 min + 2 hrs + 30 min
  • Strobe: 300 lumens, 20Hz

Powered by AA Alkaline Battery:

  • Low: 1.5 lumens, 55 hours
  • Medium: 80 lumens ~ 1.5 lumens, 1 hr 20 min + 16 hrs 50 min
  • High: 300 lumens ~ 80 lumens ~ 1.5 lumens, 1 min + 48 min + 3 hrs 15 min
  • Strobe: 300 lumens, 20Hz
Manker E05II Ti Flashlight in Ti Washstone finish, standing upright on a textured surface with blurred foliage in the background.
Manker E05II Ti Flashlight (Ti Washstone)
Manker E05II Ti Flashlight in Ti Sandblasted finish, resting on rough terrain with a rock and green plants in the background.
Manker E05II Ti Flashlight (Ti Sandblasted)
Manker E05II Ti Flashlight in Ti Mao-Green finish, standing upright against a blurred green background.
Manker E05II Ti Flashlight (Ti Mao-Green)
Manker E05II Ti Flashlight in Ti Mao-Purple finish, standing upright against a blurred green background.
Manker E05II Ti Flashlight (Ti Mao-Purple)
Manker E05II Ti Flashlight with a white diffuser cone attached, standing on a stone pillar with a blurred outdoor background.
Manker E05II Ti Flashlight with Diffuser
Group photo of four Manker E05II Ti flashlights in different finishes (purple, green, sandblasted, washstone) standing side-by-side on a textured surface with a blurred green background.
Manker E05II Ti Flashlights in various finishes

9. User Tips

  • For optimal performance and battery life, always use high-quality batteries.
  • Consider carrying a spare charged 14500 battery for extended use, especially when using high output modes.
  • The deep carry clip allows for secure attachment to pockets or gear, ensuring your flashlight is always accessible.

10. Safety Warnings

  • Battery Safety: Please use the specified model of battery. Do not mix old and new batteries, or batteries of different brands or types. Since lithium-ion batteries self-discharge, it is recommended that you remove the batteries if the flashlight will not be used for a long time, and charge the batteries at least once every 2-3 months.
  • Water Resistance: Ensure O-rings are clean and parts are tightly screwed for rated water resistance. Do not submerge non-diving lights deeply for long.
  • Heat Dissipation: High mode generates heat at the head during prolonged use, which is normal. Use intermittently to preserve LED life.
  • Eye and Skin Safety: Never point the light directly or indirectly at eyes or skin when it is on, as this may cause vision impairment or skin burns. Keep out of reach of children.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official documentation included with your product or contact the seller directly. Please keep this manual for future reference.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.