1. Product Overview
The FGHGF TPA3255 Subwoofer Active Speaker Amplifier Board is a high-performance digital amplifier designed for home audio systems, specifically for driving subwoofers. It utilizes the TPA3255 digital amplifier chip to deliver robust and clean bass output.
Key features include:
- High peak power output: 600W at 2 ohms, 300W at 4 ohms.
- Optimized pre-filter circuit for deep, clean, and controlled low-frequency response.
- High-power switching power supply for continuous energy output without 'soft feet'.
- Efficient heat dissipation via an aluminum plate, ensuring stable long-term high-power operation.
- Integrated phase-inverted and closed subwoofer switches for versatile subwoofer compatibility.
- Solid construction with an aluminum back panel and minimal bottom noise.
2. Specifications
| Feature | Specification |
|---|---|
| Model | Active Subwoofer Power Amplifier Board |
| Input | RCA, XLR |
| Output | XLR (low level) x 1, Subwoofer connector x 1 |
| Working Voltage | AC220V |
| Standby Power Consumption | 1W |
| Power Amplifier Chip | TPA3255 |
| Output Power | 600W x 1 (2 ohms), 300W x 1 (4 ohms) |
| Total Harmonic Distortion (THD) | Less than 0.2% |
| Signal-to-Noise Ratio (SNR) | 100dB |
| Frequency Response Range | 20Hz - 200Hz |
| Product Dimensions (L x W x H) | 227mm x 199mm x 42mm |
| Material | Aluminum |
| Maximum Power Per Channel (General Classification) | 6W (Note: This may refer to a general classification, actual output is 600W/300W as specified above.) |
Dimensions
The recommended hole size for installation is 207mm x 178mm.

Figure 2.1: Subwoofer amplifier board dimensions.
3. Setup and Connections
Before making any connections, ensure the amplifier board's power switch is in the 'OFF' position and it is disconnected from the AC power supply.
3.1 Rear Panel Overview

Figure 3.1: Rear panel connections and controls.
3.2 Audio Input Connections
- RCA Input: Connect your audio source (e.g., preamplifier, receiver's LFE output) to the RCA IN (L/R) jacks using appropriate RCA cables.
- XLR Input: For balanced audio signals, connect your source to the XLR IN port.
3.3 Audio Output Connections
- Subwoofer Output: Connect your passive subwoofer speaker to the dedicated subwoofer output terminals. Ensure correct polarity (positive to positive, negative to negative).
- XLR Output (Low Level): This output can be used to daisy-chain the audio signal to another amplifier or active speaker.
3.4 Power Connection
- Ensure the power switch is in the 'OFF' position.
- Connect the AC power cable to the AC-220V inlet on the amplifier board.
- Plug the other end of the power cable into a suitable AC220V power outlet.
3.5 Internal Components Overview

Figure 3.2: Internal components of the amplifier board.
4. Operating Instructions
4.1 Powering On/Off
- After all connections are made, switch the 'POWER' button to the 'ON' position. The amplifier will power on.
- To turn off, switch the 'POWER' button to the 'OFF' position.
4.2 Adjusting Controls
- VOL (Volume): Rotate the 'VOL' knob to adjust the output volume of the subwoofer. Start with a low volume and gradually increase to your desired level.
- FREQ (Frequency): Rotate the 'FREQ' knob to adjust the low-pass crossover frequency. This determines the upper frequency limit that the subwoofer will reproduce. Adjust it to blend seamlessly with your main speakers.
- Phase Switch (0°/180°): Use the phase switch to match the phase of the subwoofer's output with your main speakers. Experiment with both 0° and 180° settings to find the one that provides the most impactful and coherent bass response.
- Input Switching: Select between RCA and XLR inputs using the input switch.
4.3 Subwoofer Type Selection
The amplifier board is equipped with internal switches for phase-inverted subwoofers and closed subwoofers. Consult your subwoofer's manual to determine the appropriate setting for optimal performance. These settings are typically configured during initial setup and do not require frequent adjustment.
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the exterior of the amplifier board. Do not use liquid cleaners or solvents.
- Ventilation: Ensure adequate airflow around the amplifier board. The aluminum plate is designed for heat dissipation, so do not obstruct it.
- Safety: Always disconnect the power before performing any maintenance or internal inspection. Be aware of the AC220V working voltage and exercise caution.
6. Troubleshooting
- No Sound Output:
- Check all audio input and output connections. Ensure cables are securely plugged in and correctly polarized.
- Verify the power supply is connected and the amplifier is switched 'ON'.
- Confirm the correct input source (RCA/XLR) is selected.
- Check the volume level on both the amplifier board and your audio source.
- Distorted Sound:
- Reduce the volume level on both the amplifier and the audio source.
- Check for loose connections or damaged cables.
- Ensure the subwoofer is compatible with the amplifier's power output and impedance.
- Humming or Buzzing Noise:
- Ensure all audio cables are properly shielded and away from power cables.
- Check for ground loop issues. Try connecting all audio equipment to the same power outlet.
- Verify that the amplifier board has minimal bottom noise, as specified in the product overview. If noise persists, check external factors.
- Overheating:
- Ensure the amplifier board has sufficient ventilation and its heat dissipation aluminum plate is not obstructed.
- Reduce the volume or usage time if operating at very high levels for extended periods.
7. User Tips
- Speaker Terminal Polarity: When connecting your subwoofer, ensure you correctly identify the positive (+) and negative (-) terminals on both the amplifier and the speaker. Incorrect polarity can lead to reduced bass performance. Typically, red indicates positive and black indicates negative.
- Crossover Adjustment: Take time to fine-tune the 'FREQ' knob. A good starting point is often around 80Hz, but adjust it based on your main speakers' low-frequency capabilities and your room acoustics for the best blend.
- Phase Matching: Experiment with the 0° and 180° phase settings. One setting will usually result in a more cohesive and impactful bass response, especially if your subwoofer is not equidistant from your listening position as your main speakers.
8. Warranty and Support
For warranty information and technical support, please contact the seller or manufacturer directly. Provide your product model (TPA3255 Subwoofer Active Speaker Amplifier Board) and any relevant purchase details when seeking assistance.