Espressif ESP32-C5-DevKitC-1

Contents

ESP32-C5-DevKitC-1 Development Board User Manual

Model: ESP32-C5-DevKitC-1 | Brand: Espressif

1. Introduction

This user guide provides comprehensive information for the ESP32-C5-DevKitC-1, an entry-level development board based on the general-purpose ESP32-C5-WROOM-1 module. It integrates complete Wi-Fi (2.4 GHz/5 GHz dual-band Wi-Fi6, 802.11ax), Bluetooth® 5 (LE), Zigbee, and Thread (802.15.4) functions. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing, allowing developers to connect peripherals with jumper wires or mount the board on a breadboard.

The ESP32-C5-DevKitC-1 is equipped with the ESP32-C5-WROOM-1 module, supporting advanced wireless communication standards and offering easy connectivity to a wide range of peripherals.

ESP32-C5-DevKitC-1 Development Board with key features listed
Figure 1: ESP32-C5-DevKitC-1 Development Board highlighting its core features.

2. Safety Information

Please read and understand the following safety precautions before using the ESP32-C5-DevKitC-1 Development Board:

  • Handle the board with care to avoid electrostatic discharge (ESD) damage.
  • Ensure proper power supply voltage (5V or 3.3V) to prevent damage to the board or connected components.
  • Do not expose the board to moisture, extreme temperatures, or corrosive environments.
  • Keep the board away from flammable materials.
  • Always disconnect power before making or changing connections.

3. Package Contents

The ESP32-C5-DevKitC-1 Development Board is typically supplied in an individual package, which may include an antistatic bag or other protective packaging, depending on the retailer. Please verify that you have received the following:

  • 1 x ESP32-C5-DevKitC-1 Development Board
  • (Optional, depending on retailer) USB-A to USB-C cable

4. Product Overview

4.1. Components

The ESP32-C5-DevKitC-1 board features several key components for its operation. Refer to Figure 2 for a visual representation of the board's front view with labeled components.

ESP32-C5-DevKitC-1 front view with labeled components
Figure 2: ESP32-C5-DevKitC-1 - Front View with Component Labels.

The following table describes the key components on the board:

Key ComponentDescription
ESP32-C5-WROOM-1A general-purpose module supporting Wi-Fi 6 in 2.4 & 5 GHz dual-band (802.11ax), Bluetooth® 5 (LE), Zigbee, and Thread (802.15.4) with on-board PCB antenna.
Pin HeaderAll available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board.
5 V to 3.3 V DC/DCPower regulator that converts a 5 V supply into a 3.3 V output.
3.3 V Power On LEDTurns on when the board is connected to USB power.
USB-to-UART BridgeSingle-chip USB-to-UART bridge offering transfer rate up to 3 Mbps.
ESP32-C5 USB Type-C PortThe USB Type-C port on the ESP32-C5 chip supports USB 2.0 full speed, with a data transfer rate of up to 12 Mbps. Note that this port does not support the 480 Mbps high-speed transfer mode. This port is used for power supply to the board, flashing applications to the chip, and communication with the chip via USB protocols, as well as for JTAG debugging.
Boot ButtonDownload button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.
Reset ButtonPress this button to restart the system.
USB Type-C to UART PortUsed for power supply to the board, flashing applications to the chip, as well as communication with chip ESP32-C5 via the on-board USB-to-UART bridge.
RGB LEDAddressable RGB LED, driven by GPIO27.
J5Used for current measurement. See details in Section Current Measurement.

4.2. Block Diagram

The block diagram below shows the components of ESP32-C5-DevKitC-1 and their interconnections.

System Block Diagram of ESP32-C5-DevKitC-1
Figure 3: System Block Diagram of ESP32-C5-DevKitC-1.

4.3. Pin Layout

The ESP32-C5-DevKitC-1 breaks out most of the I/O pins to pin headers J1 and J3 on both sides of the board. Refer to Figure 4 for a detailed pin layout diagram and Tables 2 and 3 for pin descriptions.

ESP32-C5-DevKitC-1 Pinout Diagram with ESP32-C5-WROOM-1 module and GPIOs
Figure 4: ESP32-C5-DevKitC-1 Pinout Diagram.

J1 Pin Header:

No.NameType1Function
13V3P3.3 V power supply
2RSTIHigh: enables the chip; Low: disables the chip.
32I/O/TMTMS3, GPIO2, LP_GPIO2, LP_UART_RTSN, ADC1_CH1, FSPIQ
43I/O/TMTDI, GPIO3, LP_GPIO3, LP_UART_CTSN, ADC1_CH2
54I/O/TMTCK, GPIO4, LP_GPIO4, LP_UART_RXD, ADC1_CH3, FSPIHD
65I/O/TMTDO, GPIO5, LP_GPIO5, LP_UART_TXD, ADC1_CH4, FSPIWP
70I/O/TGPIO0, XTAL_32K_P, LP_GPIO0, LP_UART_DTRN
81I/O/TGPIO1, XTAL_32K_N, LP_GPIO1, LP_UART_DSRN, ADC1_CH0
927I/O/TGPIO272 3
106I/O/TGPIO6, LP_GPIO6, LP_I2C_SDA, ADC1_CH5, FSPICLK
117I/O/TGPIO73, LP_GPIO7, LP_I2C_SCL, FSPID
1226I/O/TGPIO26
1325I/O/TGPIO25
145VP5 V power supply
15GGGround
16NC-No connection

1 P: Power supply; I: Input; O: Output; T: High impedance.

2 Used to drive the RGB LED.

3 MTMS, GPIO7, GPIO27, and GPIO28 are strapping pins of the ESP32-C5 chip. These pins are used to control several chip functions depending on binary voltage values applied to the pins during chip power-up or system reset.

J3 Pin Header:

No.NameTypeFunction
1GGGround
2TXI/O/TU0TXD, GPIO11
3RXI/O/TU0RXD, GPIO12
424I/O/TGPIO24
523I/O/TGPIO23
6NC/15I/O/TNo connection/GPIO154
710I/O/TGPIO10, FSPICS0
89I/O/TGPIO9, PAD_COMP1
98I/O/TGPIO8, PAD_COMP0
10NC-No connection
1128I/O/TGPIO283
12GGGround
1314I/O/TGPIO14, USB_D+
1413I/O/TGPIO13, USB_D-
15GGGround
16NC-No connection

4 In modules integrated with SPI SPRAM, this pin is already used for SPICS1 function, thus unavailable for external use. In modules without SPI PSRAM, this pin can be used as GPIO15.

3 MTMS, GPIO7, GPIO27, and GPIO28 are strapping pins of the ESP32-C5 chip. These pins are used to control several chip functions depending on binary voltage values applied to the pins during chip power-up or system reset.

For detailed schematics, refer to the ESP32-C5-DevKitC-1 Schematic (PDF) mentioned in the official user guide.

5. Specifications

The ESP32-C5-DevKitC-1 Development Board offers the following technical specifications:

  • Core: 32-bit RISC-V single-core @ 240MHz
  • Wireless Connectivity: Wi-Fi 6 IEEE 802.11ax (2.4 GHz and 5 GHz), Bluetooth LE 5, IEEE 802.15.4 (Zigbee and Thread)
  • SRAM: 384 KB
  • ROM: 320 KB
  • GPIOs: 29 programmable GPIOs
  • Peripherals: 2x SPI, 2x UART, 1x I2C, RMT, LED PWM (6 channels), 1x 12-bit ADC (6 channels), TWAI®, USB Serial/JTAG, ETM, MCPWM
  • Dimensions: Approximately 53.60 mm (Length) x 25.40 mm (Width) x 6.50 mm (Height)
  • Weight: Approximately 0.05 kg
Dimensions diagram of the ESP32-C5-DevKitC-1 in mm
Figure 5: ESP32-C5-DevKitC-1 Dimensions (Unit: mm).

6. Setup and Installation

This section guides you through the initial hardware setup and software configuration for the ESP32-C5-DevKitC-1.

6.1. Required Hardware

  • ESP32-C5-DevKitC-1 Development Board
  • USB-A to USB-C cable
  • Computer running Windows, Linux, or macOS

Note:

Be sure to use a good quality USB cable. Some cables are for charging only and do not provide the needed data lines nor work for programming the boards.

6.2. Power Supply Options

There are three mutually exclusive ways to provide power to the board:

  • USB Type-C to UART port and ESP32-C5 USB Type-C port: Either one or both can be used. This is the recommended default power supply method.
  • 5V and GND pin headers: Connect a 5V power source to the 5V pin and ground to the GND pin.
  • 3V3 and GND pin headers: Connect a 3.3V power source to the 3V3 pin and ground to the GND pin.

Note:

When using 3V3 and GND pin headers to power the board, please remove the J5 jumper, and connect an ammeter in series between the external power supply and the 3V3 pin header to measure the module's current. This is because the 3V3 pin header supplies power directly to the module, bypassing the J5 headers. Removing the J5 jumper disconnects unnecessary circuits, allowing for a more accurate measurement of the module's current.

6.3. Software Setup

To set up the development environment and flash firmware, please proceed to the official Espressif ESP-IDF Get Started guide. This guide will provide detailed instructions for installing the necessary tools and flashing an application example onto your board.

Official Espressif ESP-IDF Get Started Guide: https://docs.espressif.com/projects/esp-idf/en/latest/esp32c5/get-started/index.html

7. Operating Instructions

7.1. Initial Power-Up

Before powering up your ESP32-C5-DevKitC-1, ensure it is in good condition with no obvious signs of damage. Connect the board to your computer using a USB-C cable. The 3.3V Power On LED should illuminate, indicating the board is receiving power.

7.2. Flashing Firmware

Once your development environment is set up (as described in Section 6.3), you can flash your custom firmware or example applications to the ESP32-C5-DevKitC-1. Typically, this involves:

  1. Connecting the board via USB.
  2. Holding down the Boot Button.
  3. Pressing and releasing the Reset Button while still holding the Boot Button.
  4. Releasing the Boot Button. The board is now in Firmware Download mode.
  5. Using the ESP-IDF tools on your computer to flash the desired firmware.

7.3. Connecting Peripherals

The broken-out pin headers (J1 and J3) allow for easy connection of external peripherals using jumper wires or by mounting the board on a breadboard. Refer to the Pin Layout section (4.3) for detailed information on each pin's function.

8. Maintenance

To ensure the longevity and optimal performance of your ESP32-C5-DevKitC-1 Development Board, follow these maintenance guidelines:

  • Keep the board clean and free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Store the board in an antistatic bag when not in use to prevent ESD damage.
  • Avoid physical stress or bending of the board.
  • Do not attempt to repair the board yourself if it is damaged; contact support for assistance.

9. Troubleshooting

If you encounter issues with your ESP32-C5-DevKitC-1, consider the following troubleshooting steps:

  • Board not powering on: Ensure the USB cable is properly connected and functional. Try a different USB port or cable. Verify your power supply method is correctly implemented.
  • Firmware flashing issues: Double-check that the board is in Firmware Download mode (Boot button sequence). Ensure your development environment (ESP-IDF) is correctly installed and configured. Verify the USB cable is a data-capable cable, not just for charging.
  • Peripheral not responding: Check all wiring connections to the pin headers. Verify the correct GPIOs are being used in your code. Ensure the peripheral itself is functional and correctly powered.

10. User Tips

  • Use Quality Cables: Always use a high-quality USB-A to USB-C cable that supports data transfer for reliable programming and communication.
  • Check Official Documentation: For the latest updates, detailed schematics, and advanced usage, always refer to the official Espressif documentation and user guides.
  • Community Support: Engage with the Espressif community forums for solutions to common problems and to share your projects.

11. Warranty and Support

For detailed warranty information and technical support, please refer to the official Espressif website or contact your retailer. The comprehensive user guide and other resources are available at:

https://docs.espressif.com/projects/esp-dev-kits/en/latest/esp32c5/esp32-c5-devkitc-1/user_guide.html

For specific product inquiries or issues, please contact the seller directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.