1. Introduction
The Estardyn ESP32-C3 SuperMini Plus is a compact IoT development board designed for a wide range of low-power IoT and wireless wearable applications. It integrates the Espressif ESP32-C3 WiFi and Bluetooth chip, offering excellent RF performance and supporting IEEE 802.11 b/g/n and Bluetooth 5 (LE) standards. Its small form factor and single-sided surface mount design make it ideal for space-constrained projects.
The board features a 32-bit RISC-V single-core processor, operating at up to 160 MHz, along with ample memory (400KB SRAM, 384KB ROM, and 4MB Flash). It provides various serial interfaces including UART, I2C, and SPI, and includes a reset button and a bootloader mode button for easy programming and control.


2. Setup
2.1 Hardware Setup
Before you begin, ensure you have the following components:
- 1 x Estardyn ESP32-C3 SuperMini Plus Development Board
- 1 x USB Type-C cable (ensure it supports data transfer, not just power)
- Optional: FPC Antenna (if using external antenna)
- Optional: Pin headers for breadboard compatibility

External Power Supply
If an external power supply is required, connect the positive (+) terminal of the external power supply to the 5V pin on the board, and the negative (-) terminal to the G (Ground) pin. The maximum current for the external power supply is 500mA. Note that when using an external power supply, you cannot simultaneously use the USB power supply.
Warning: When soldering, exercise extreme caution to avoid short-circuiting the positive and negative electrodes, as this can cause short circuits and damage the board and connected equipment.
WiFi Antenna Connection
The board includes an antenna interface. If using an external FPC antenna, connect it to the designated interface. The image below illustrates the components of a WiFi antenna.

2.2 Software Setup (Arduino IDE)
To program the ESP32-C3 SuperMini Plus, you will need the Arduino IDE and the ESP32 board package.
- Download and Install Arduino IDE: Download and install the latest version of the Arduino IDE from the official website.
- Add ESP32 Board Package URL:
- Open the Arduino IDE.
- Go to
File > Preferences. - In the "Additional Boards Manager URLs" field, add the following URL:
https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json - Click "OK".
- Install ESP32 Board Package:
- Go to
Tools > Board > Boards Manager... - In the Boards Manager window, search for "esp32".
- Select the latest version of the "esp32" package by Espressif Systems and click "Install".
- Go to

3. Operating Instructions
3.1 Connecting the Board
- Connect the ESP32-C3 SuperMini Plus to your computer using a data-capable USB Type-C cable.
- In the Arduino IDE, go to
Tools > Board > ESP32and selectESP32C3 Dev Module. You may need to scroll down the list to find it. - Go to
Tools > Portand select the serial port corresponding to your connected ESP32-C3 SuperMini.
3.2 Uploading a Program (Flashing LED Example)
To test the board, you can upload a simple program to make the onboard LED flash.
- Copy the following code into the Arduino IDE:
// define led according to pin diagram int led = 8; void setup() { // initialize digital pin led as an output. pinMode(led, OUTPUT); } // the loop function runs over and over again forever void loop() { digitalWrite(led, HIGH); // turn the LED on (HIGH is the voltage level) delay(1000); // wait for a second digitalWrite(led, LOW); // turn the LED off by making the voltage LOW delay(1000); // wait for a second } - Click the "Upload" button (right arrow icon) in the Arduino IDE.
- After a successful upload, press the RESET button on the ESP32-C3 SuperMini Plus board to execute the program.
- You should observe the onboard LED flashing with a 1-second interval.
4. Maintenance
The ESP32-C3 SuperMini Plus Development Board is a robust electronic component, but proper care ensures its longevity and reliable operation:
- Handle with Care: Avoid dropping or subjecting the board to physical shocks.
- Keep Dry: Protect the board from moisture and liquids, which can cause short circuits and damage.
- Cleanliness: Keep the board free from dust and debris. Use a soft, dry brush or compressed air for cleaning if necessary.
- Storage: When not in use, store the board in an anti-static bag or container to prevent electrostatic discharge damage.
- Power Off: Always disconnect power before making any physical connections or disconnections to the board.
5. Troubleshooting
5.1 COM Port Not Recognized in IDE
If the Arduino IDE does not recognize the COM port for your ESP32-C3 SuperMini Plus, you may need to manually enter download mode:
- Method 1 (Power-on): Press and hold the BOOT button while powering on the board.
- Method 2 (Reset Sequence): Press and hold the BOOT button, then press and release the RESET button, and finally release the BOOT button.
Each time you connect the board for programming, it might require re-entering download mode. Port instability can sometimes occur, which you might detect by a port identification sound from your computer.
5.2 Program Does Not Run After Upload
After a successful program upload, you must press the RESET button on the ESP32-C3 SuperMini Plus board to initiate the execution of the newly uploaded program.
5.3 ESP32-C3 SuperMini Serial Port Cannot Print
If you are experiencing issues with serial output (e.g., using Serial.print()) not appearing in the Serial Monitor, ensure that the "USB CDC On Boot" option is set to "Enabled" in the Arduino IDE's Tools menu for your board.
6. Specifications
The following table details the technical specifications of the Estardyn ESP32-C3 SuperMini Plus Development Board:
| Feature | Description |
|---|---|
| Processor | ESP32-C3, 32-bit RISC-V single-core, up to 160 MHz |
| Wireless Connectivity | WiFi 802.11 b/g/n, Bluetooth 5 (LE) |
| Memory | 400KB SRAM, 384KB ROM, 4MB Flash |
| Interfaces | UART, I2C, SPI, ADC, PWM, RGB LED, Antenna interface |
| Supply Voltage | 5V |
| Dissipation Power | 1W |
| Operating Temperature | -30°C to +50°C |
| Dimensions | 18mm x 22.5mm |
| Package Type | SMD (Surface Mount Device) |
| Application | Computer, IoT, Wireless Wearables |

7. User Tips
- External Antenna Activation: If you are using an external FPC antenna, you may need to install a jumper and potentially desolder or disable the built-in antenna trace to ensure the external antenna is properly utilized. Consult advanced documentation for specific jumper configurations.
- USB Cable Quality: Always use a high-quality USB Type-C cable that supports both power and data transfer to avoid connectivity and programming issues.
- Reset After Upload: Remember to press the RESET button on the board after uploading new firmware to ensure the program starts executing correctly.
8. Warranty and Support
For any technical assistance, warranty claims, or further inquiries regarding your Estardyn ESP32-C3 SuperMini Plus Development Board, please contact the seller or manufacturer directly through the platform where the product was purchased. Provide your order details and a clear description of the issue to facilitate prompt support.
Always refer to the official Espressif documentation for the ESP32-C3 chip for in-depth technical details and advanced programming guides.