HTOOL HT004

Contents

HTOOL HT004 Signal Amplifier User Manual

Low Noise 100k-6GHz Wideband Preamplifier

1. Introduction

Thank you for choosing the HTOOL HT004 Signal Amplifier. This ultra-low noise wideband preamplifier is designed to enhance signal reception across a broad frequency range, from 100 kHz to 6 GHz. Its compact design and robust performance make it suitable for various applications, including BeiDou/GPS receivers, FM radio reception, radar systems, EMC receiver systems, and software-defined radio (SDR) setups. This manual provides essential information for the safe and effective use of your device.

2. Safety Information

  • Always use the specified power supply (TYPE-C cable) to prevent damage to the device.
  • Avoid exposing the amplifier to extreme temperatures, humidity, or direct sunlight.
  • Do not attempt to open or modify the device. Unauthorized modifications will void the warranty and may cause damage or injury.
  • Ensure proper impedance matching (50 ohms) for input and output connections to optimize performance and prevent signal reflection.
  • Keep the device away from strong electromagnetic fields to avoid interference.

3. Package Contents

Verify that all items are present in your package:

  • 1 x HTOOL HT004 Signal Amplifier
  • 1 x USB Type-C Cable
  • 1 x Storage Box
HTOOL HT004 Signal Amplifier and USB Type-C cable in a clear storage box.
HTOOL HT004 Signal Amplifier and USB Type-C cable in a clear storage box.

4. Specifications

ParameterValue
Model NumberHT004
TypeUltra Low Noise Amplifier (LNA)
Frequency Range100 kHz - 6 GHz (0.1 MHz - 6 GHz)
Gain20 dB (typical, refer to gain curve for frequency specifics)
Noise Figure (NF)5 dB (typical, refer to NF curve for frequency specifics)
P1dB10 dBm @ 2 GHz
Input/Output Impedance50 ohms
Power SupplyTYPE-C cable
Current Consumption< 80 mA
Output ConnectorSMA female
Dimensions (L*W*H)68 * 40 * 15 mm (approx. 4.7 * 4 * 1.4 cm without protruding SMA)
Weight35 g (including host + TYPE-C cable)
CertificationCE
DIY Supplies CategoryElectrical

Performance Curves

Graph showing Noise Figure (NF) performance across the frequency range.
Noise Figure (NF) vs. Frequency
Graph showing Gain performance across the frequency range.
Gain vs. Frequency
Graph showing P1dB performance across the frequency range.
P1dB vs. Frequency

5. Setup

5.1 Device Overview

Top and bottom views of the amplifier, highlighting RF-IN, USB-BAT switch, Type-C port, LED indicator, and RF-OUT.
HT004 Amplifier: Top and Bottom Views

5.2 Power Connection

  1. Connect the provided USB Type-C cable to the 'Type-C' port on the amplifier.
  2. Connect the other end of the USB cable to a suitable 5V USB power source (e.g., computer USB port, USB wall adapter).
  3. The LED indicator will illuminate when the device is powered on.

5.3 Signal Connections

  1. Connect your signal source (e.g., antenna, signal generator) to the 'RF-IN' port using an SMA connector.
  2. Connect your receiver or measurement equipment to the 'RF-OUT' port using an SMA connector.
  3. Ensure all connections are secure and have 50-ohm impedance for optimal performance.

5.4 Battery Option (No Battery Version)

If you have the 'No Battery Version' of the HT004, it is designed to be compatible with a 3.7V 500mAh 603030 battery for portable operation. This battery is not included and must be purchased separately. Ensure correct polarity when installing the battery.

Internal view of the amplifier showing the Type-C port, LED, RF-OUT, and a recommendation for a 3.7V 500mAh 603030 battery.
Internal view with battery recommendation for 'No Battery Version'

6. Operating Instructions

  1. After connecting the power and signal cables as described in the Setup section, the amplifier is ready for operation.
  2. The 'USB-BAT' switch controls the power source. Switch to 'USB' for external Type-C power or 'BAT' if an internal battery is installed (for compatible versions).
  3. The LED indicator confirms that the device is powered on and functioning.
  4. The amplifier will boost the incoming RF signal from the 'RF-IN' port and output the amplified signal through the 'RF-OUT' port.
Video: HTOOL HT004 Signal Amplifier unboxing and overview.

7. Application Scenarios

The HTOOL HT004 Signal Amplifier is versatile and can be used in various applications:

  • BeiDou/GPS Receivers: Improve signal strength for navigation and positioning systems.
  • Receiver Systems: Enhance reception for FM radio, radar, and other communication systems.
  • EMC Receiver Systems: Aid in electromagnetic compatibility testing and signal analysis.
  • Software Radio Receivers (SDR): Boost weak signals for SDR applications, expanding reception capabilities.

8. Troubleshooting

ProblemPossible CauseSolution
No power/LED offPower cable not connected, faulty cable, or power source issue. USB-BAT switch in wrong position.Check Type-C cable connection and power source. Ensure USB-BAT switch is set correctly (USB for external power, BAT for internal battery). Try a different USB cable or power adapter.
No signal amplificationIncorrect RF connections, faulty cables, or signal source issue.Verify RF-IN and RF-OUT connections are secure. Check signal source and receiver. Ensure SMA cables are not damaged.
Weak or distorted signalImproper impedance matching, strong interference, or signal source too weak/strong.Ensure all components are 50-ohm impedance. Check for nearby sources of electromagnetic interference. Adjust signal source output if possible.

9. Maintenance

  • Cleaning: Use a soft, dry cloth to clean the exterior of the amplifier. Do not use liquid cleaners or solvents.
  • Storage: When not in use, store the amplifier in its provided storage box in a cool, dry place, away from dust and moisture.
  • Connections: Periodically check all cable connections for wear or damage. Replace any damaged cables immediately.

10. Warranty and Support

The HTOOL HT004 Signal Amplifier is covered by a standard manufacturer's warranty against defects in materials and workmanship. For warranty claims or technical support, please contact your retailer or the HTOOL Official Store directly. Please retain your proof of purchase for warranty service.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.