ThinkRider XXPRO

Contents

ThinkRider XXPRO Direct Drive Smart Bike Trainer

User Manual

1. Product Introduction

Thank you for purchasing the ThinkRider XXPRO Smart Bike Trainer. Please read this instruction manual carefully before use to ensure proper setup and operation.

ThinkRider XXPRO Smart Bike Trainer
The ThinkRider XXPRO Intelligent Direct-Drive Bike Trainer.
Power Accuracy Diagram
The XXPRO features a third-generation power module and a new AI algorithm for ±1% power accuracy.
Rider using the trainer with virtual simulation
Experience 25% Cross-Sim gradient simulation and up to 2500W power output.

2. Package Contents

The standard package includes the following items:

  • XXPRO Smart Bike Trainer (1 unit)
  • Power adapter (1 unit)
  • 8-9-10 speed washer (1 unit)
  • Quick release adapters (Support 130/135mm)
  • Thru axle adapters (Support 142/148mm)
  • Specification manual
  • 17mm wrench
  • Oil disc caliper plug
  • Puncture Protection (4 units)
  • Cassette adjustment spacer

Special Note:

The standard accessories do not include the cassette, Thru axle release, Quick release, BLE, and ANT+ USB receiver. If you require these, they must be purchased separately from your dealer.

Diagram of package contents including trainer, adapters, tools, and power adapter
Visual representation of the XXPRO trainer and its included accessories.

3. Setup

3.1 Trainer Installation

  1. Place the trainer on a flat, sturdy surface, ensuring no obstacles or dangerous objects are nearby.
  2. Install the base and tighten the screws to ensure the trainer is stable.
  3. Connect the trainer to a standard 110V-220V power outlet using the original power adapter.
  4. The trainer comes with a standard freehub body, compatible with Shimano HG 8-12-speed cassettes, and SRAM 8-11-speed road and mountain bike cassettes.
  5. Note: 11-speed standard cassettes can be installed directly. 8-10-speed cassettes require a spacer. Campagnolo or SRAM XDR freehub bodies must be purchased separately.

Footing Installation Note:

The left side of the leveling foot is shorter, while the right side (drive side) is longer.

3.2 Adapters Installation

The non-drive side adapter can be inserted in different directions to accommodate various axle spacing sizes. Refer to the diagrams below for specific instructions.

130-135 Quick Release Adapter Installation:

  • For 130mm quick release: Use the short end exposed adapter.
  • For 135mm quick release: Use the long end exposed adapter.
  • Always install the quick release adapter.

142-148 Thru Axle Adapter Installation:

  • For 142mm thru axle: Use the short end exposed adapter.
  • For 148mm thru axle: Use the long end exposed adapter.
  • Always install the thru axle adapter.

For a visual guide on installation, please watch the video below:

Official installation and setup guide for the ThinkRider XXPRO Smart Bike Trainer.

4. Operation Guidelines and Caveats

  • Always install and use the trainer on a flat and sturdy surface.
  • Before each use, carefully check that your quick-release lever or thru-axle is securely locked to the frame to prevent loosening during use, which could cause personal injury and property damage.
  • Do not touch the moving parts of the trainer with your hands or any objects.
  • After long-term use, the trainer's freewheel may become hot; do not touch it.
  • During cycling, keep children and pets away from the trainer.
  • Do not touch the freewheel or disassemble the bicycle while the inertia flywheel is still spinning.
  • During use, keep the trainer away from fire sources, water sources, and other obstacles.
  • Do not stand on the trainer while pedaling; avoid excessive rocking; pay attention to safety.
  • Users with cardiovascular and cerebrovascular diseases or other conditions unsuitable for high-intensity exercise are strictly prohibited from using the trainer. Consult a doctor before starting or modifying any exercise training plan.
  • Individuals who are not capable of responsible behavior should not use the trainer.

Disclaimer: The manufacturer is not responsible for personal and property damage caused by abnormal use of the trainer.

5. Firmware Upgrade and Software Settings

5.1 Firmware Update

The cycling trainer's firmware can be upgraded. For firmware updates, please download the 'ThinkRider Tools' app on your mobile phone.

Special Note:

During the upgrade, keep your phone within 1 meter of the cycling trainer. Do not exit the upgrading interface, perform any other operations, or turn off the power of the cycling trainer until the firmware upgrade is completed.

5.2 Cycling APP Settings

This trainer is a general equipment compatible with most standard third-party cycling software. After downloading and installing cycling software on your cellphone or computer, switch on the trainer's power, open the software, find the device connection interface, search for, and connect to the "cycling trainer" signal.

For a visual guide on firmware and software, you may refer to this video: https://youtu.be/5TqY8dbD5YE

6. Specifications

Feature Specification
StructureSteel + Plastic
Drive TypeMotor Self-Driving (Direct Drive)
Power Supply Voltage100V-240V
Resistance TypeBLDC
Maximum Simulated Slope25% (when cycling speed is less than 18 km/h, the simulated gradient is less than 25%)
Maximum Resistance PowerAbout 2500 Watts
Power Accuracy±1%
Noise Level56dB
Package Weight18kg
Package Size66 x 52 x 21 cm
Wireless ConnectionBluetooth, ANT+, Wifi (Pro and above)
Output DataPower, Cadence, Speed, Left-Right Balance
Rim Size CompatibilityRoad: 24/650c/700c; MTB: 24"/26"/650B/29"
Hub Type Compatibility130/135QR (Standard), 12x142mm and 12x148mm thru axle
Cassette CompatibilityShimano HG (8-12 speed), SRAM (8-11 speed). XDR or CP freehub body sold separately.
Software CompatibilityZwift, Onelap, Rouvy, TrainerRoad, BKOOL Cycling, Wahoo SystemX, ThinkRider (Standard protocol compatible with most cycling software)
Set-up Dimensions48x50x52cm
Net Weight18kg
Product Parameters Table comparing XXPRO and X2Max
Detailed product parameters for the XXPRO trainer.
H-Shape Base Design for stability
The H-shape base design provides unparalleled stability.
Downhill Simulation feature with rider
Rechargeable Downhill Simulator for an immersive experience without pedaling.

7. User Tips

  • Quiet Operation: Users frequently praise the XXPRO for its quiet operation, making it suitable for use without disturbing others.
  • Downhill Feature: The downhill simulation feature is a notable luxury, enhancing the realism of virtual rides.
  • Easy Setup: Many users find the setup and pairing with devices like Garmin and smartphones to be straightforward.
  • Structured Training: The trainer is highly recommended for individuals interested in structured training and data-driven workouts due to its precise power meter and data output.
  • Cassette Not Included: Be aware that the cassette is not included with the trainer and must be purchased separately to match your bike's gearing.
  • App Connectivity: To avoid connectivity issues, ensure the trainer is not simultaneously connected to multiple cycling apps or bike computers. If an app cannot find the trainer, check for existing connections and disconnect them before attempting to connect with the new app.

8. Troubleshooting

8.1 Connectivity Issues

If your smart trainer cannot be found by a cycling application, consider the following:

  • Simultaneous Connections: The trainer cannot be connected to two apps simultaneously. If the smart trainer is already connected to an app (indicated by a solid red light), the next app will not be able to find it.
  • Resolution: First, check for and disconnect any previous connections (or unplug and restart the trainer; a flashing red light indicates a waiting connection state). Then, proceed with connecting to the desired app.

8.2 Compatibility Questions

  • SRAM XDR / Campagnolo: The standard freehub body is Shimano HG compatible. For SRAM XDR or Campagnolo cassettes, a specific freehub body must be purchased separately.
  • Zwift Cog: The trainer is compatible with Zwift Cog, but you must use the ThinkRider freehub body, not the one supplied with Zwift Cog.
  • 7-Speed Cassettes: While the trainer supports 8-12 speed Shimano HG cassettes, 7-speed cassettes may require additional spacers or specific adapters not included.

9. Maintenance

  • Cleaning: Regularly wipe down the trainer with a damp cloth to remove sweat and dust. Avoid using harsh chemicals.
  • Inspection: Periodically check all screws and connections to ensure they are tight and secure.
  • Moving Parts: Keep the freewheel and other moving parts free from debris. Do not lubricate the freewheel unless specifically instructed by ThinkRider support.
  • Storage: When not in use, store the trainer in a dry, clean environment away from extreme temperatures.

10. Warranty and Support

10.1 Warranty

The product is guaranteed for one year from the date of purchase. If the product fails during the warranty period due to an original device quality problem or assembly process, the company will provide free maintenance and spare parts replacement.

The warranty does not cover product damage or malfunction caused by the following reasons:

  • Damage caused by use or installation not in accordance with the instructions.
  • Product damage caused by human factors or accident.
  • Unauthorized disassembly of the product without contacting the company or dealer.
  • Ingress of water causing equipment failure.
  • Aging and scratches caused by normal use.

After the expiration of the warranty period, the company will continue to provide maintenance services, but corresponding maintenance costs will be charged.

10.2 Support

If you have any after-sales questions or require technical assistance, please contact our engineers:

Email: service2@thinkrider.com

For more information, visit: www.thinkrider.com

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.