Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of the EOENKK Car Stereo Wiring Harness with Canbus Box (Model: CAN011-R). This product is designed to integrate an aftermarket 16PIN Android stereo with your vehicle's existing electrical system, preserving original functions such as steering wheel controls, factory amplifier, and cameras.
Vehicle Compatibility
This wiring harness is compatible with the following Nissan vehicle models and years:
- Nissan Teana Altima: 2014-2018
- Nissan X-Trail Qashqai: 2014-2018
- Nissan Rogue: 2014-2018
- Nissan Navara NP300: 2014-2018
- Nissan Kicks: 2016-2018
- Nissan Maxima: 2015-2018
- Nissan Murano: 2015-2018
Important Note: This harness is designed to fit OEM radios with a 4.3" screen or without a screen. It is specifically for use with 16PIN Android stereos.
Setup and Installation
Before beginning installation, ensure your vehicle's ignition is off and the battery is disconnected to prevent electrical damage.
Pre-installation Checklist:
- Verify your aftermarket Android stereo has a 16PIN power plug.
- Confirm your vehicle is one of the compatible Nissan models and years listed above.
- Ensure your OEM radio either has a 4.3" screen or no screen.
Harness Components Overview:
Refer to the diagram above for identification of the following components:
- Main Power Connector (to Android Stereo)
- Antenna Adapter
- RCA Video Input (e.g., for aftermarket backup camera)
- Canbus Box Connector
- Canbus Box (P/N: DF-RZ-02)
- Vehicle Specific Connector 1
- Vehicle Specific Connector 2
- Vehicle Specific Connector 3
- Vehicle Specific Connector 4
- Vehicle Specific Connector 5
- USB Adapter Connector (for OEM USB port)
Installation Steps:
- Carefully remove your vehicle's OEM radio from the dashboard.
- Disconnect all existing wiring from the OEM radio.
- Connect the vehicle-specific connectors (6, 7, 8, 9, 10) from the new harness to the corresponding ports in your vehicle's wiring loom.
- Connect the main power connector (1) of the harness to the 16PIN power plug of your Android stereo.
- Connect the Canbus Box (5) to its designated connector (4) on the harness.
- If your vehicle has a factory Bose amplifier, locate the 'AMP CONT' line on the harness and ensure it is correctly wired to the amplifier control input on your Android stereo.
- Connect the antenna adapter (2) to your Android stereo's antenna input.
- If connecting to the Nissan OEM USB port, use the provided USB adapter cable and connect it to the USB adapter connector (11) on the harness.
- If using an aftermarket backup camera, connect its RCA video output to the RCA video input (3) on the harness.
- Once all connections are secure, reconnect your vehicle's battery.
- Test the functionality of the Android stereo, steering wheel controls, backup camera, 360 camera, and amplifier (if applicable).
- Carefully re-install the Android stereo into the dashboard.
Operating Functions
This wiring harness is designed to maintain and integrate several original vehicle functions with your new Android stereo:
- Steering Wheel Control (SWC): Allows you to use your vehicle's existing steering wheel buttons to control the Android stereo (e.g., volume, track skip, mode).
- Original Backup Camera: Integrates the factory-installed backup camera, displaying its feed on your Android stereo's screen when reversing.
- Factory Bose/JBL Amplifier: Provides compatibility with your vehicle's original premium sound system amplifier. Ensure the 'AMP CONT' line is correctly wired.
- Original 360 Camera: Supports the factory 360-degree camera system, if equipped, displaying its views on the Android stereo.
Maintenance
The wiring harness is a passive component and requires minimal maintenance. To ensure longevity and reliable performance:
- Regular Checks: Periodically inspect the connections behind the stereo for any signs of loosening or corrosion.
- Keep Dry: Ensure the area where the harness is installed remains dry and free from moisture.
- Avoid Extreme Temperatures: While designed for automotive environments, extreme temperatures can degrade wiring over time.
- Cleanliness: Keep the area around the harness free from dust and debris.
Troubleshooting
If you encounter issues after installation, consider the following troubleshooting steps:
- No Power to Stereo:
- Double-check all power connections from the harness to the Android stereo and the vehicle's wiring.
- Ensure the vehicle's battery is properly connected and charged.
- No Sound or Poor Sound Quality:
- If your car has a factory amplifier (e.g., Bose), ensure the 'AMP CONT' line on the harness is correctly wired to the amplifier control input on your Android stereo. This is a common oversight.
- Verify all speaker wire connections are secure and correctly matched.
- Steering Wheel Controls Not Working:
- Ensure the Canbus Box is correctly connected and functioning.
- Check the settings within your Android stereo for steering wheel control configuration. Some stereos require manual programming.
- Backup Camera / 360 Camera Not Displaying:
- Verify the RCA video input (3) is securely connected to the camera's video output.
- Check the camera input settings on your Android stereo.
- USB Port Not Functioning:
- Ensure the USB adapter cable is correctly connected to both the harness and the Nissan OEM USB port.
If these steps do not resolve the issue, please refer to the Warranty/Support section for further assistance.
Specifications
| Product Type | Car Stereo Wiring Harness with Canbus Box |
| Brand | EOENKK |
| Model Number | CAN011-R |
| Vehicle Compatibility | Nissan Qashqai, Rogue, X-Trail, Teana Altima (2014-2018), Kicks (2016-2018), Maxima, Murano (2015-2018), Navara NP300 (2014-2018) |
| Radio Compatibility | OEM Radio with 4.3" Screen or without screen |
| Stereo Compatibility | 16PIN Android Stereo |
| Supported Functions | Steering Wheel Control (SWC), Factory Bose/JBL Amplifier, Original Backup Camera, Original 360 Camera |
| Material | Premium Core Material |
User Tips
- Always confirm your Android radio has a 16PIN power plug before purchasing and installing this harness to ensure compatibility.
- For vehicles with a factory amplifier, remember to connect the dedicated 'AMP CONT' wire from the harness to your new stereo's amplifier control input. This step is crucial for sound output.
- The harness is designed for a plug-and-play installation, minimizing the need for wire cutting. This makes the installation process quicker and less complex.
- Ensure your OEM radio matches the specified compatibility (4.3" screen or no screen) to avoid fitment issues.
Warranty and Support
For any issues encountered during installation or use, please contact the seller's technical support. You can typically find contact information through your order details or the seller's official store page. Provide your order number for faster assistance.