Introduction
This manual provides detailed instructions for the safe and efficient operation, maintenance, and troubleshooting of your WPM MS-130D Steam Milk Frother. Designed for both home and commercial use, this powerful machine delivers strong steam for creating dense milk foam, heating beverages, and preparing various coffee and tea drinks. Please read this manual thoroughly before using the appliance and keep it for future reference.
Important Safety Instructions
- Voltage Warning: This product operates on 220-240V, 50Hz AC power only. Ensure your local power supply is compatible before connecting the appliance. Using an incorrect voltage may result in damage to the unit and pose a safety hazard.
- Hot Surfaces: The steam pipe, nozzle, and surrounding areas become extremely hot during operation. Always use the anti-scalding handle and exercise extreme caution to prevent burns.
- Children and Pets: Keep the appliance out of reach of children and pets.
- Water Tank: Never operate the frother without sufficient water in the tank.
- Cleaning: Always unplug the appliance before cleaning. Allow hot parts to cool down before handling.
- Maintenance: Do not attempt to repair or disassemble the appliance yourself. Refer all servicing to qualified personnel.

Figure 1: Appliance with hot surface warning.
Product Overview
Components

Figure 2: Labeled components of the MS-130D Steam Milk Frother.
- 800ML Water Tank: Removable tank for water supply.
- Steam Knob: Controls the steam output.
- Cleaning Button: Initiates the automatic cleaning cycle.
- Stainless Steel Body: Durable and easy-to-clean exterior.
- Water Tray: Collects drips and spills, removable for cleaning.
- 500ML Milk Jug: Included accessory for frothing milk.
- Steam Nozzle (Double Hole): Designed for efficient milk frothing, detachable for cleaning.
- Steam Pipe: Delivers steam to the nozzle.
- Anti-scalding Handle: Provides a safe grip for adjusting the steam pipe.
- Operation Indicator: Light to show operational status.
Key Features
- Compact and Professional Design: Suitable for various settings.
- Rapid Heating: Warms milk to 60 degrees Celsius in approximately 40 seconds.
- Creamy Foam Production: Double-hole nozzle ensures rich, dense milk foam.
- 4 Bar Strong Steam Pressure Pump: Provides stable and uninterrupted steam output.
- High Power Heater: 1450W for efficient performance.
- Stainless Steel Casing: Ensures durability and a beautiful appearance.
- One-Button Automatic Cleaning: Simplifies daily and deep cleaning routines.
- 360° Adjustable Steam Wand: Offers flexibility for frothing from various angles.
- Multi-purpose Machine: Ideal for coffee, milk tea, fruit tea, and other hot beverages.
Setup Guide
- Unpacking: Carefully remove the frother from its packaging. Retain packaging for future transport or storage.
- Placement: Place the appliance on a stable, flat, heat-resistant surface, away from water sources and direct heat.
- Water Tank Installation: Ensure the 800ML water tank is properly seated in its designated slot.
- Fill Water Tank: Fill the water tank with clean, filtered water up to the MAX line. Do not overfill.
- Power Connection: Connect the power cord to a grounded 220-240V, 50Hz electrical outlet.
- Initial Rinse (First Use): Before first use, perform a cleaning cycle without milk to flush out any manufacturing residues. Fill the water tank, turn on the machine, and activate the steam for a short period, then run the automatic cleaning cycle.
Operating Instructions
Frothing Milk
- Prepare Milk: Fill the 500ML milk jug with cold milk. Do not fill more than halfway to allow for expansion.
- Position Jug: Place the milk jug under the steam nozzle. Submerge the tip of the steam nozzle just below the surface of the milk.
- Activate Steam: Turn the steam knob to the "START" position to release steam.
- Froth Milk: As steam is released, move the jug slightly up and down to incorporate air and create foam. Maintain the nozzle just below the surface for aeration, then lower it deeper for heating.
- Monitor Temperature: Froth until the desired temperature (around 60-65°C) and texture are achieved. The machine is designed to warm milk to 60°C in about 40 seconds.
- Stop Steam: Turn the steam knob to the "OFF" position to stop the steam.
- Clean Nozzle: Immediately after frothing, wipe the steam wand with a damp cloth to remove any milk residue. Briefly open the steam valve again to purge any milk from inside the nozzle.
General Beverage Heating
The MS-130D can also be used to heat other beverages like water for tea or fruit tea. Follow similar steps as frothing milk, ensuring the steam nozzle is submerged in the liquid to be heated. Always exercise caution due to hot liquids and steam.

Figure 3: Milk frothing and multi-purpose beverage heating.

Figure 4: Steam control button and 360° adjustable steam wand.
Maintenance and Cleaning
Regular cleaning is crucial for maintaining hygiene and extending the service life of your WPM MS-130D Steam Milk Frother.
Daily Cleaning
- After each use, immediately wipe off the steam pipe and nozzle with a wet towel for 3 seconds to remove any milk residue.
- Briefly open the steam valve to purge any remaining milk from inside the steam tube.
- Empty and rinse the water tray.
Deep Cleaning (Automatic)
- Ensure the water tank is filled with water.
- Add a suitable descaling agent to the water tank as per the descaling agent's instructions.
- Press the red cleaning button to activate the automatic cleaning mode. The machine will perform a self-cleaning cycle.
- After the cycle, empty and rinse the water tank and water tray thoroughly.
Detachable Parts Cleaning
- The water collection basin is detachable for easy disassembly and cleaning.
- The double-hole steam nozzle can be removed for thorough cleaning or replacement.

Figure 5: One-button automatic cleaning for extended service life.

Figure 6: Detachable water collection basin for easy cleaning.
Troubleshooting
This section addresses common issues you might encounter with your steam milk frother. For problems not listed here, please contact customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| No steam or weak steam output. |
|
|
| Milk not frothing properly. |
|
|
| Appliance not turning on. |
|
|
Specifications
| Attribute | Detail |
|---|---|
| Brand | WPM |
| Model Number | MS-130D |
| Power (W) | 1450W |
| Voltage | 220-240V |
| Frequency | 50Hz |
| Rotation Rate (RPM) | 8000 |
| Water Capacity | 800ML |
| Net Weight | 6.7 kg |
| Gross Weight | 7.82 kg |
| Product Dimensions (L*W*H) | 380mm * 140mm * 340mm |
| Material | Stainless Steel |
| Operation Method | Full-Automatic |
| Origin | Mainland China |

Figure 7: Product dimensions.
User Tips
- For best frothing results, always use very cold milk.
- Experiment with different types of milk (whole, skim, oat, almond) to find your preferred foam texture.
- Purge the steam wand before and after each use to ensure dry steam and prevent milk residue buildup.
- Regularly descale the machine, especially in areas with hard water, to maintain optimal performance and extend its lifespan.
- Keep the steam nozzle clean; a clogged nozzle will significantly reduce steam pressure and frothing quality.
Warranty and Support
The WPM MS-130D Steam Milk Frother comes with a one-year warranty from the date of purchase, covering manufacturing defects. This warranty does not cover damage caused by misuse, neglect, unauthorized repairs, or normal wear and tear.
For technical support, warranty claims, or any questions regarding your appliance, please contact the retailer or manufacturer's customer service. Please have your model number (MS-130D) and proof of purchase ready when contacting support.