1. Safety Information
⚠ Pay attention to the safety precautions below before using this de-soldering station.
- Follow the manual to use this de-soldering station. DO NOT use it for unspecified purposes.
- The air outlet and its nearby areas are extremely hot. Be careful so as not to be burnt.
- In the idle state, the handle must be placed on the handle rack in a correct manner. DO NOT place it on the working station or another place. After the job is done, allow the de-soldering station to cool down below 100℃ (entering into the sleeping mode) before turning off the power switch.
- Keep the air outlet unblocked. Any blockage must be cleared.
- DO NOT place a sharp object on the air outlet hose as the latter may be damaged.
- When using this de-soldering station, maintain at least 2mm between the air outlet and the target item.
- Different wind nozzles with slightly different temperatures can be selected for different applications.
- If this de-soldering station will not be used for a long time, pull out the power plug.
- Handle the de-soldering station with care. DO NOT tap on the handle or violently shake the station.
- Regularly check and maintain this station. DO NOT use it when it has damages, especially when the power cable or air gun handle wire is damaged.
- DO NOT use this station when it is wet or when your hands are wet; otherwise you may risk a short circuit or electric shock.
- DO NOT use this station near inflammable gases or other combustible substances. After using this station, DO NOT place it around inflammable gases or other combustible substances immediately.
- The wall surface, ceiling, floor, arch bar and other places may contain combustible substances. Using the de-soldering station in these places may ignite these substances, which can be difficult to discover and thus may result in property loss or casualties. When working in these places, move the hot air de-soldering handle back and forth wherever possible. The handle's lingering or pause at a position may ignite the combustible substances near this position.
- Children are unaware of how dangerous electric products can be. DO NOT use or store this station in a place accessible to a child. DO NOT allow a child to get near or touch this station.
- When the power is on, if the soldering iron tip temperature is greater than 200-450°C (392-842°F), abuse of use may even lead to fires or burns. Please strictly observe the following matters:
- Do not touch the iron tip and metal area.
- Do not use near inflammable goods.
- The soldering iron tip is very hot. It may cause dangerous accidents. Please turn off the power after using it.
- When changing parts, please turn off the machine and wait for the tip to cool.
- To avoid damage to the soldering station, please strictly observe the following matters:
- This product uses rated voltage and frequency (refer to the label on the back of the machine).
- It is strictly prohibited to use this product when it is damaged, especially when the power cable is damaged.
- This product uses a three-wire grounding plug, and must be inserted into a three-hole grounding socket. If you need to extend the cord, use a grounded three-wire power cord.
- Do not use the soldering iron for any work except welding.
- Do not knock the soldering tip on the workbench to clean it, as this may seriously damage the soldering tips.
- When replacing parts, please use original factory parts.
- Do not tamper with the soldering iron without safety precautions.
- Do not wet the soldering iron, and do not use it with wet hands.
- There will be smoke when welding, please confirm the ventilation environment.
2. Features
- Integrated 2-in-1 design: Combines a hot air gun and a T12 soldering iron.
- High Power: 760W for efficient desoldering and welding.
- Digital Display: High-definition LCD screen for clear temperature and air volume display.
- Temperature Calibration Function: Allows for precise temperature adjustments.
- Memory Storage Channels: Both the air gun and soldering iron have three storage channels (CH1, CH2, CH3) for different temperatures and air volumes.
- Induction Sleep Function: The soldering iron automatically enters sleep mode when placed on its stand, stopping heating to prolong tip life.
- Automatic Cooling Function: The hot air gun automatically cools down when placed on its holder, extending the heating element's lifespan and protecting the handle.
- Dual-Mode Air Gun: Equipped with 2 cyclone nozzles and 2 direct air nozzles, offering low noise and large air volume.
- Celsius/Fahrenheit Conversion: Easily switch between temperature units.
- Suitable for various applications: Desoldering/soldering SOIC, CHIP, QFP, PLCC, BGA components, thermal shrinkage, drying, paint/adhesive removal, unfreezing, pre-heating, sterilization, and plastic soldering.
- Designed for lead-free hot air desoldering.
3. Product Overview




Product Demonstration Video
This video demonstrates the key features of the SUGON 212, including temperature calibration, standby temperature settings, storage channels for air gun and soldering iron, and Celsius/Fahrenheit conversion.
4. Setup
- Unpacking: Carefully unpack all components from the box. Verify that all items listed in the "Package Included" section are present.
- Placement: Place the desoldering station on a flat, stable, and heat-resistant workbench. Ensure there is adequate ventilation around the unit.
- Nozzle Installation: Select the required air nozzle for your task and install it onto the hot air gun handle. For general use, a larger size air nozzle is often recommended.
- Soldering Iron Stand: Place the soldering iron handle into its designated stand.
- Power Connection: Connect the power cord to the station and then to a grounded power outlet. Ensure the power switch is in the OFF position before plugging in.
- Initial Power On: Turn on the main power switch. The digital display should illuminate.
5. Operating Instructions
5.1. Basic Operation
- Power On: After connecting the power cord, turn on the main power switch.
- Activating Tools: Remove the hot air gun handle from its holder or pick up the soldering iron. The system will enter normal working state, and the display will show the set and actual temperatures.
- Temperature Setting (Hot Air Gun & Soldering Iron):
- Increase Temperature: Press the "▲" button once to increase the set temperature by 1°C. Press and hold "▲" for at least one second to rapidly increase the temperature until the button is released at the target temperature.
- Decrease Temperature: Press the "▼" button once to decrease the set temperature by 1°C. Press and hold "▼" for at least one second to rapidly decrease the temperature until the button is released at the target temperature.
- Air Volume Setting (Hot Air Gun):
- Increase Air Volume: Press the "▲" button (air volume) once to increase the air volume by 1 level. Press and hold "▲" for at least one second to rapidly increase the air volume until the button is released at the target level.
- Decrease Air Volume: Press the "▼" button (air volume) once to decrease the air volume by 1 level. Press and hold "▼" for at least one second to rapidly decrease the air volume until the button is released at the target level.
- Storage Channels (CH1, CH2, CH3):
- Storing Settings: After setting the desired temperature and air volume, long-press the corresponding channel button (CH1, CH2, or CH3) for the hot air gun or soldering iron to save the current settings to that channel.
- Recalling Settings: Short-press the corresponding channel button (CH1, CH2, or CH3) for the hot air gun or soldering iron to recall the saved settings.
- Sleep Mode:
- Hot Air Gun: When the hot air gun handle is placed back into its holder, the system automatically enters cold air cooling mode. Once the temperature drops below 100°C, it enters sleep mode ("SLP" displayed).
- Soldering Iron: When the soldering iron handle is placed on its stand, it quickly stops heating and enters sleep mode ("SLP" displayed).
- Power Off: After completing work, ensure the hot air gun has cooled down and the soldering iron is in sleep mode. Turn off the main power switch. If not used for a long time, unplug the power cord.
5.2. Special Functions
- Temperature Unit Conversion (℃/℉): In the shutdown state, press and hold the hot air gun temperature "▼" button and then turn on the power switch to switch between Celsius (℃) and Fahrenheit (℉).
- Buzzer On/Off: In the shutdown state, press and hold the hot air gun "▼" button and then turn on the power switch to toggle the buzzer sound on or off.
- Soldering Iron Standby Temperature Setting: In the shutdown state, press and hold the soldering iron temperature "▼" button and then turn on the power switch. This enters the standby temperature setting page. Use the "▲" or "▼" buttons to set the standby temperature (0, 150, 180, 200°C). Setting to 0 will turn off standby heating. The setting will automatically save after 3 seconds.
- Temperature Compensation (Air Gun & Soldering Iron):
- Air Gun: In the shutdown state, press and hold both air gun temperature "▲" and "▼" buttons simultaneously, then turn on the power switch. This enters the air gun temperature compensation interface. Use "▲" or "▼" to set the compensation value. It will automatically save and exit after 3 seconds.
- Soldering Iron: In the shutdown state, press and hold both soldering iron temperature "▲" and "▼" buttons simultaneously, then turn on the power switch. This enters the soldering iron temperature compensation interface. Use "▲" or "▼" to set the compensation value. It will automatically save and exit after 5 seconds.
6. Maintenance
6.1. Soldering Iron Tip Maintenance
The high temperature will weaken the soldering iron tip. Always choose the lowest possible temperature for your task. A good quality soldering iron tip can recover well, and lower temperatures can still achieve effective welding while protecting sensitive components.
- Cleaning: Regularly use a cleaning sponge or copper wire balls to clean the soldering iron tip. After welding, soldering flux can damage the tip, leading to welding errors or temperature differences.
- When Not in Use: When not using the soldering iron, do not keep it at high temperature for a long time. High temperatures can cause the tip to oxidize and get damaged.
- After Use: After using, clean the soldering iron tip and tin it (apply a fresh layer of solder) to prevent oxidation.
- Inspection: Do not remove oxide from the soldering iron tip with a knife. If the tip has black oxide, use a sponge to clean it until it's removed. If the soldering iron tip is deformed or rusted, replace it with a new one.
- Temperature Setting for Cleaning: Set the temperature to 250°C (482°F) for cleaning. After the temperature stabilizes, check and clean the soldering iron tip.

6.2. Replacing Hot Air Gun Heating Element
Note: Replace the heating element only after it has cooled down and the power is disconnected.
- Loosen the anti-scald sleeve on the hot air gun handle and remove it from the handle.
- Unscrew the screws fixing the handle and open the handle.
- Unscrew the screws fixing the terminal block.
- Remove the old heating element and install the new one.
- Reassemble the handle in reverse order.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No power/Display off | Power cord not connected, power switch off, fuse blown. | Check power connection, turn on switch, replace fuse if necessary. |
| Hot air gun not heating or weak airflow | Heating element failure, fan motor issue, blocked air outlet. | Check for blockages, ensure handle is correctly seated, replace heating element/fan if faulty. |
| Soldering iron not heating | Heating element failure, poor connection, tip oxidation. | Check connections, clean/replace tip, replace heating element if faulty. |
| Temperature display inaccurate | Sensor issue, need for calibration. | Perform temperature compensation/calibration as per instructions. |
| Unit does not enter sleep mode | Handle not correctly placed on stand/holder, sensor issue. | Ensure handle is properly seated. |
If the problem persists after attempting these solutions, please contact customer support or a qualified technician.
8. Specifications
| Parameter | Value |
|---|---|
| Model Number | SUGON 212 |
| Maximum Power | 760W |
| Voltage | AC 220V 50/60HZ / AC 110V 50/60HZ (Dual Voltage Support) |
| Hot Air Gun Temperature Range | 100-500°C (212-932°F) |
| Soldering Iron Temperature Range | 200-450°C (392-842°F) |
| Hot Air Gun Air Volume Range | 20-100 levels |
| Soldering Iron Power | 60W |
| Hot Air Gun Memory Channels | 3 |
| Soldering Iron Storage Channels | 3 |
| Certification | CE |
| Origin | Mainland China |
| Package Weight | 2.5 kg |
| Package Dimensions (L x W x H) | 28 cm x 26 cm x 23 cm |
9. User Tips
- Temperature Calibration: Utilize the temperature calibration function to ensure precise temperature readings, especially for sensitive components.
- Pre-set Channels: Make good use of the 3 storage channels for both the hot air gun and soldering iron to quickly switch between frequently used temperature and air volume settings. This saves time and improves workflow efficiency.
- Celsius/Fahrenheit Conversion: Easily switch between Celsius and Fahrenheit display modes based on your preference or regional standards.
- Soldering Iron Handle: The T12 handle offers higher heat resistance and a longer service life compared to standard handles.
- Air Nozzles: Experiment with the included cyclone and straight air nozzles to find the best fit for different desoldering tasks, considering the balance between airflow and precision.
10. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the official product documentation or contact the seller/manufacturer directly. Keep your purchase receipt as proof of purchase.
User Manual (PDF): A detailed user manual in PDF format is available for download. You can access it via the following link: SUGON 212 User Manual (PDF).