1. Important Safety Information
Please read this manual thoroughly before operating the device. Keep this manual for future reference.
- Do not operate the device in a way that distracts you from driving.
- Ensure all wiring is correctly connected to prevent damage to the unit or vehicle.
- Avoid exposing the unit to extreme temperatures or moisture.
- If the product has been subjected to a long journey or extreme conditions, it is recommended to test the unit before full installation.
2. Setup and Installation
2.1 Before Installation
Thank you for purchasing our product. When you receive the product, please do not install it directly into the car. Due to the long journey, the product may be affected. Please test the machine before installing.
2.2 Rear Interface Description
The following diagrams illustrate the rear interface connections for the multimedia player. Ensure all connections are secure and correct.

Figure 2.2.1: CAIXI 7 Inch IPS Wireless CarPlay Android Auto 2 Din Stereo Car Radio Multimedia Player with included accessories.

Figure 2.2.2: Steering Wheel Controls and Infrared Remote.

Figure 2.2.3: Product Information and Accessories (Power Cord, Steering Wheel Remote Control).
Power Plug Wiring

Figure 2.2.4: Power Plug Wiring Diagram.
Wiring Notes:
- Yellow (B+): Connect to constant 12V positive power. This maintains power for memory functions.
- Red (ACC): Connect to ignition switch 12V positive power.
- Black (GND): Connect to ground wire.
- Orange (ILLUMINATION): Connect to backlight control for illumination.
- Pink (REVERSE): Connect to reversing camera control line.
- Brown (KEY2) & Orange/black striped (KEY1): Steering Wheel Control lines.
- Blue (ANT): Auto Antenna Power.
- Speaker Wires: There are 8 speaker cables. Each cable must not be grounded, shared, or touch other lines to prevent sound distortion or unit overheating.
2.3 Reversing Camera Installation Method
The multimedia player supports a rear view camera for parking assistance.

Figure 2.3.1: Rear View Camera Display with Parking Lines.

Figure 2.3.2: Reversing Camera Wiring Diagram.
- Find Wiring Port: Locate the reverse control line (pink wire) on the unit's power line. Connect this line to a +12V positive pole; the screen will turn blue when reverse gear is engaged.
- Connect Camera: The camera typically has two sockets. Connect the red socket to the power cable, and the yellow socket to the video cable. The red wire of the camera's power cable and the video cable should be screwed together to the positive pole of the reverse lamp. The black wire of the power cable is not used.
- Video Input: Connect the other end of the video cable to the CAM video input interface on the back of the unit. The red line coming out of the video line connects to the reverse control line of the power line.
- Important: If the reversing camera is not installed, do not connect the REVERSE/BACK cable. Leave it unconnected. Incorrect connection can cause the unit to display improperly or automatically enter reverse mode.
2.4 CANBUS Connection (Optional)
The CANBUS box is used for specific car models to integrate with vehicle systems. If your car requires a CANBUS connection, follow the instructions below. If the CANBUS box and black buckle are connected simultaneously, it may cause the radio to fail to shut down after the car is turned off.

Figure 2.4.1: CANBUS Connection for High-end and Low-end Models.
2.5 Learning Steering Wheel Controls
To use the steering wheel controls, you need to program them with the unit.

Figure 2.5.1: Steering Wheel Control Learning Interface.
- Press and hold a button on your original car's steering wheel.
- On the unit's screen, find the icon corresponding to the function of that steering wheel button.
- Click the icon to assign the function. Learning is successful when the icon changes color.
3. Operating Instructions
3.1 Wireless CarPlay and Android Auto
The unit supports both wireless CarPlay and Android Auto for seamless smartphone integration.

Figure 3.1.1: CarPlay and Android Auto Interface.
Wired Connection:
- Simply connect your smartphone to the unit via a USB data cable. The unit will automatically enter the CarPlay or Android Auto interface.
Wireless Connection:
- On your mobile phone, enable both Bluetooth and Wi-Fi.
- Connect your phone to the unit's Bluetooth.
- The unit will automatically enter the CarPlay or Android Auto interface. The signal is transmitted via Wi-Fi. If Wi-Fi is turned off, CarPlay/Android Auto will disconnect.
Note: Android Auto functionality may not be supported in all countries and requires Google Play services to be available locally. You need to download and install the Android Auto app and use a mobile phone with Android 6.0 or higher.
3.2 Online Music and More
The multimedia player supports various online media playback options and navigation.

Figure 3.2.1: Online Music, Navigation, and Entertainment.
- Movies: Enjoy watching movies directly on the 7-inch screen.
- Navigation: Utilize precise navigation with highlighted routes.
- Music: Freely enjoy online music from various platforms.
- Bluetooth Phone: Make and receive calls directly from the unit.
3.3 Voice Assistant Control
For a safer driving experience, the unit supports voice assistant control.

Figure 3.3.1: Voice Assistant Control Interface.
In CarPlay/Android Auto mode, you can use Siri/Google voice assistant for hands-free operations such as:
- "Hey Siri" / "Hey Google"
- "Dial Number"
- "Open Map"
- "Play Music"
- "Help me open message"
3.4 Adjustable Button Color
The unit features adjustable button backlighting with 7 color options to match your car's interior or personal preference.

Figure 3.4.1: Adjustable Button Color Options.
You can choose from: Original light color, Red light, Yellow light, Blue light, Fuchsia light, Orange light, Green light, Purple light.
4. Maintenance
To ensure optimal performance and longevity of your multimedia player, follow these simple maintenance guidelines:
- Screen Cleaning: Use a soft, lint-free cloth slightly dampened with water or a screen cleaner specifically designed for electronics. Do not use harsh chemicals or abrasive materials.
- Software Updates: Periodically check for software updates from the manufacturer to ensure the best performance and access to new features.
- General Care: Keep the unit free from dust and debris. Avoid spilling liquids on the device.
5. Troubleshooting
This section provides solutions to common problems you might encounter.
5.1 Cannot Boot Normally
- Wiring Check: Ensure the yellow (B+), red (ACC), and black (GND) wires are correctly connected. Yellow to constant +12V, Red to ignition +12V, Black to ground. Incorrect or insufficient connections will prevent booting.
- Fuse Check: If the 3 wires are connected correctly but it doesn't boot, check the fuse on the yellow line. If the fuse is broken, replace it. If the fuse is fine, twist the yellow and red wires together, turn on the key, and press the power button to test.
- Original Car Wiring: If using original car wiring, ensure it matches the unit's standard. Non-standard wiring or direct plugging of original car plugs into the new unit without proper adaptation can cause issues or damage.
- Persistent Boot Failure: If the unit still doesn't boot after checking all connections and fuses, test the unit with a separate 12V battery or power supply by connecting yellow and red to +12V and black to ground. If it boots, the issue is with your car's wiring. If it doesn't boot, the unit may be faulty.
5.2 Automatic Shut-down
- Cable Error: If the blue cable (automatic antenna power supply) is connected to the unit's power cable, it may cause automatic shutdown. Correct the wiring.
- Unstable Voltage: Find a 12V-5A power supply and re-test the unit. If it still shuts down automatically, the unit is faulty. If it works fine with the test power supply, the issue is with your car's power supply.
5.3 Noise Issues
- Speaker Power: If the original speaker power is too low, increasing the unit's volume may cause noise. Avoid setting the volume too high.
- Grounded Speaker Cable: If a speaker cable is grounded, connect an iron speaker cable directly to the unit's speaker cable.
5.4 Remote Control Not Working
- Test Remote: Use your phone camera to check if the remote's infrared light flashes when a button is pressed. If not, replace the battery. If it flashes, the remote is working, and the issue might be with the unit's receiver.
5.5 Settings Not Saved (No Memory)
- Incorrect Wiring: The yellow and red lines are connected together (yellow to positive, red to key control).
- Reversed Wires: The yellow and red wires are reversed. Correct their positions.
5.6 Bluetooth Not Working
Turn on the machine, search for the unit's Bluetooth name on your mobile phone, and click Connect. After connecting, you should be able to make calls or play music via Bluetooth.
5.7 Product Emits Smoke
Replace the FUSE. If the problem persists, the internal circuit may be burned. After-sales service is required.
5.8 Sound Cannot Be Adjusted
- Reset Unit: Reset the unit or unplug and replug the power cord.
- Volume Knob: If the volume knob is broken, it needs to be replaced.
5.9 Reversing Camera Does Not Display
- Wiring: Check for incorrect or missing wiring. Refer to section 2.3 for the correct installation method.
- Faulty Camera: If the camera's lamp does not light up when properly wired, the camera may be broken and needs replacement.
Tips: If the device is updated, the functions are subject to change without prior notice.
6. Specifications
| Feature | Specification |
|---|---|
| Din Size | Double Din |
| Display Size | 7 inches |
| Resolution | HD 1024*600 |
| Touch Screen | Yes, full touch capacitive screen |
| Operating System | Windows CE (Note: Not Android system) |
| Out Power | 50W x 4 |
| Voltage | 12 V |
| Item Weight | 0.8 kg |
| Item Size | 178*102mm |
| Max External Memory | 128G (for TF/Micro SD Slot) |
| TF/Micro SD Slot | 2 |
| ROM | SD / USB |
| Special Features | Support steering wheel control, Mobile Phone, MP3 players, CarPlay, Android Auto, Reversing Input, Split Screen |
| Digital Media Format | CD, DVD-R/RW, DVD-RAM, VIDEO CD, Mp3, MP4, WMA, JPEG |
| OSD Language | Chinese (Simplified), Polish, German, Russian, French, Portuguese, Japanese, Turkish, Hebrew, Spanish, Italian, English |
| Material Type | Abs+ |
| Certification | CE |
| Mirror Link | Iphone & Android (Android 4.4-8.1) |
| Microphone | Built-in |
| Input Interface | USB, SD, RCA, Bluetooth |
| Bluetooth Phone Book | Support |
| Bluetooth Music | Support |
| AV-OUT | Support |
6.1 Package Contents
- 1 x Car MP5/MP4 Player
- 1 x Remote Control
- 1 x Cable Set
- 1 x Frame
- 2 x Bracket
- 1 x User Manual
- 1 x Steering wheel remote (Optional)
- 1 x Camera (Optional)
- 1 x WIFI DVR (Optional)
7. User Tips
- Picture Quality: The unit features an IPS screen with HD 1024*600 resolution, providing a wide viewing angle and clear picture quality.
- Pre-Installation Test: Always test the unit before full installation to ensure it's working correctly after transit.
- Correct Wiring: Use the provided radio cable for installation. Different factories may have different cable designs, and incorrect wiring can damage the unit.
- Problem Resolution: If you encounter any issues, contact customer service before leaving feedback. They are committed to providing solutions.
- DVR Connection: For connecting a car DVR, refer to the provided link for instructions: DVR Connection Guide.
8. Warranty and Support
For detailed item guides and documents, including the user manual in PDF format, please refer to the official documentation:
If you need further assistance or have any questions, please contact customer service. You can find contact information via the QR codes below:

Figure 8.1: Customer Service Contact Information (QR Codes).