1. Introduction
Thank you for choosing the LUCKY FF1108-1CT fish finder. This device is designed to help you locate fish and understand underwater structures with ease.
The FF1108-1CT has two different user modes: SIMULATION and TRANSDUCER. You can switch between these modes using the User Mode menu choice.


2. How FF1108-1CT Sonar Works
The FF1108-1CT is designed for ease of use. Simply power it on and begin fishing. The device automatically determines depth and adjusts to keep the bottom and fish visible on the display.
It utilizes sonar technology to send sound waves from the transducer into the water. The returned 'echoes' are plotted on the display, creating a precise picture of the underwater environment, including distances to objects like the bottom, fish, and structures.
When used with the Portable Cable transducer, the FF1108-1CT employs a 200 kHz sonar system with a wide 45° area of coverage. This system is effective in both shallow and very deep fresh and salt water. Factors such as boat speed, wave action, bottom hardness, water conditions, and transducer installation can influence depth capability.


3. Display View
The FF1108-1CT presents underwater information in an easy-to-understand format. The top of the display represents the water surface at the transducer, while the bottom corresponds to the Depth Range automatically selected for the current water depth. The Bottom Contour changes as the depth beneath the boat varies. Digital readouts provide precise information for depth, fish, and water temperature.
As your boat moves, variations in terrain and bottom composition are displayed. Fish, baitfish, and thermoclines (underwater temperature changes) are shown when detected. Underwater conditions can vary significantly, so some experience and interpretation are necessary to fully utilize the FF1108-1CT. Use the display as a guide for common conditions and practice using the device over known bottom types.


4. Setup
4.1. Powering ON and OFF
To power on the FF1108-1CT, press and hold the POWER-MENU key for 3 seconds. To power off, press and hold the POWER-MENU key until the unit shuts down.
When the FF1108-1CT powers on, the device will temporarily display a screen for 5 seconds. From this menu, use the arrow keys to select either 'Transducer' (for actual use) or 'Simulation' (for learning). If no selection is made, the unit will default to normal water use.
4.2. Connecting the Transducer
The FF1108-1CT uses a wired transducer. Ensure the transducer cable is securely connected to the main unit. The transducer consists of a float, the transducer unit, and a cable.



5. Operating Instructions
5.1. The Menu System
The FF1108-1CT features a simple menu system to access adjustable settings. To activate the menu, press the POWER-MENU key. Press it repeatedly to cycle through menu settings one at a time. When a menu setting is displayed, use the LEFT and RIGHT Arrow keys to adjust the setting. Menu settings automatically disappear after a few seconds. In normal operating mode, most menu settings saved to memory will not revert to their default values when the unit is turned off.
5.2. Language
Press the POWER-MENU key until 'LANGUAGE' appears. Use the arrow keys to select your desired language. Available languages include English, German, Russian, Italian, Spanish, French, Chinese, Japanese, Korean, Hungarian, Portuguese, Finnish, Polish, Dutch, Greek, Swedish, Czech, Danish, Romanian, and Slovak.
5.3. Brightness
Press the POWER-MENU key until 'BRIGHTNESS' appears. Use the arrow keys to adjust the display brightness from 1 to 9.
5.4. Sensitivity
Press the POWER-MENU key until 'SENSITIVITY' appears. Sensitivity controls the level of detail shown on the display. Increasing sensitivity shows more sonar returns from small baitfish and suspended debris, but can clutter the display. Decreasing sensitivity reduces clutter. If set too low, the display may not show many sonar returns, including fish. Adjust sensitivity from 1 to 10.
5.5. Depth Low Limit
Press the POWER-MENU key until 'Depth low limit' appears. 'Auto' is the default setting, where the lower range adjusts automatically to follow the bottom. You can manually set the limit from 1 to 100 meters. If the current depth exceeds the manual setting, the bottom will not be visible. Select 'AUTO' to return to automatic operation.
5.6. Depth Upper Limit
Press the POWER-MENU key until 'Depth upper limit' appears. Select 'Auto' to magnify the area around the bottom, revealing fish and structures close to the bottom that might not be visible during normal operation. When set to 'Auto', upper and lower depth ranges adjust automatically to keep the area above and below the bottom on display. Select 'Off' to return to normal operation. (Off, 1 to 100 meters).
5.7. Shallow Alarm
Press the POWER-MENU key until 'SHALLOW ALARM' appears. Select 'OFF' for no alarm, or set a depth from 1 to 100 meters. An audible alarm will sound when the depth is equal to or less than the set value.
5.8. Fish Alarm
Press the POWER-MENU key until 'FISH ALARM' appears. Select 'Off' for no fish alarm, or choose one of the fish symbols to set the alarm. An alarm will sound when the FF1108-1CT detects fish corresponding to the alarm setting. The Fish Alarm will only sound if 'FISH ICON' is also set to 'On'. Options include: Large fish only, Large fish/Middle fish, Large fish/Middle/Small fish.
5.9. Fish Icon
Press the POWER-MENU key until 'FISH ICON' appears. Select 'Off' to view 'raw' sonar returns, or 'On' to view fish symbols. Fish ICON uses advanced signal processing to interpret sonar returns and displays a fish symbol when specific requirements are met. A selected number of possible fish returns will be displayed with their associated depth.
5.10. Units
Press the POWER-MENU key until 'UNITS' appears. Use this setting to select the units for depth and temperature (M/°C, FT/°C, M/°F, FT/°F).
5.11. Ice Fishing Mode
To switch to ice fishing mode, press the right arrow button on the device.


6. Maintenance
Follow these simple procedures to ensure your FF1108-1CT continues to deliver top performance:
- If the unit comes into contact with salt spray, wipe the affected surfaces with a cloth dampened in fresh water.
- Do not use chemical glass cleaners on the lens, as this may cause cracking.
- When cleaning the LCD protective lens, use a chamois and a non-abrasive, mild cleaner. Do not wipe while dirt or grease is on the lens. Be careful to avoid scratching the lens.
- If your boat remains in the water for a long period, marine growth can reduce transducer effectiveness. Periodically clean the transducer face with liquid detergent.
- If your boat is out of the water for a long period, it may take time for the transducer to wet when returned to the water. Small air bubbles can cling to the transducer surface and interfere with operation. These bubbles will dissipate over time, or you can wipe the transducer face with your fingers after it's in the water.
- Never leave the unit in a closed car or trunk, as extremely high temperatures can damage the electronics.
ATTENTION: The device is only spray waterproof. Exercise caution during use.
7. Troubleshooting
Many repair requests received by LUCKY involve units that do not actually need repair. Here are some common issues and their solutions:
7.1. Nothing happens when I turn the unit on.
Check and ensure the battery is fully charged. If not, charge the battery first.
7.2. No transducer detected.
The FF1108-1CT can detect and identify if a transducer is connected. When powering on, ensure the appropriate transducer connector is plugged into the unit. Inspect the transducer cable for breaks, kinks, or cuts. Also, ensure the transducer is fully submerged in water. If the transducer is connected via a switch, temporarily connect it directly to the unit and try again. If these steps don't resolve the issue, the transducer itself may be faulty.
7.3. No bottom reading visible on the display.
In very deep water, you may need to manually increase the sensitivity setting to maintain a graphic depiction of the bottom. Inspect the transducer cable for damage. If no obvious problem is found, the transducer may be faulty.
7.4. Gaps in bottom reading and inconsistent digital depth in shallow water.
The FF1108-1CT works reliably in water 2 feet (0.7 meters) or deeper. Remember that depth is measured from the transducer, not the water surface.
7.5. Many black dots at high speeds and high sensitivity settings.
This indicates noise or interference. Noise can be caused by nearby electronic devices; try turning them off. Engine noise can also cause interference, intensifying at higher RPMs. Increase engine speed with the boat stationary to isolate this. Propeller cavitation can also appear as noise if the transducer is mounted too close to the propeller (less than 15 inches or 380mm away), causing turbulence that interferes with the sonar signal.
8. Specifications
| Feature | Specification |
|---|---|
| Display | 2.4 inch TFT color LCD |
| Backlighting | On/off White LED |
| Depth Capability | 328 feet (100m) |
| Sonar Coverage | 45 degrees beam angle |
| Sonar Frequency | 200Khz |
| Power Source | 3.7V rechargeable Lithium-ion Battery |
| Power Input | DC 10-18V |
| Waterproof Design | Level-4 (spray-water-proof) |
| Operational Temperature | 14°F to 122°F (-10°C to 50°C) |
| Built-in Memory | Stores sonar settings when turned off |
9. User Tips
- Battery Life: The battery lasts a long time, even in cold conditions, making it suitable for winter fishing.
- Bottom Texture: The device effectively displays the texture of the bottom, which can be useful for identifying fishing spots.
- Kayak Use: Many users find this fish finder perfect for kayaking due to its portability and ease of mounting.
- Easy Setup: The device is generally easy to set up and use, even for beginners.
- Ice Fishing: The FF1108-1CT is well-suited for ice fishing, offering good functionality at an affordable price.
- Testing Environment: For accurate readings, always test the fish finder in outdoor deep water. Using it in smooth, hard places like water tanks, swimming pools, or fish ponds can cause inaccurate sonar reception.
10. Warranty & Support
LUCKYLAKER Terminal Service Center is dedicated to providing convenient and efficient service to customers. For more information, you can visit the official website or contact customer service via email.
- Service Center: Provides general support.
- Aftersale Service: Assistance with post-purchase issues.
- Part Price: Information on replacement part costs.
- Reservation Service: For scheduling service appointments.
- Online Service: Support available online.
- Authenticity Identification: To verify genuine LUCKY products.
Email: service@luckylaker.com
Website: www.luckylaker.com
For a complete and detailed user manual, please refer to the official PDF document: LUCKY FF1108-1CT User Manual (PDF)