DIVEDEER YTK-02

Contents

DIVEDEER Smart Water Spray Window Cleaning Robot

Model: YTK-02

User Manual

Introduction

Thank you for purchasing the DIVEDEER Smart Water Spray Window Cleaning Robot. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your device. Please read it carefully before using the product.

The DIVEDEER Window Cleaning Robot features a vacuum motor for strong adsorption to glass surfaces, allowing it to move freely. It includes two well-designed cleaning wheels with microfiber cleaning cloths that are easily removable and replaceable. The robot utilizes artificial intelligence for path planning, border detection, and automatic cleaning. A manual remote control mode is also available for flexible operation.

Video: Demonstration of the DIVEDEER Window Cleaning Robot in action, showcasing its movement and cleaning capabilities.

Important Safety Instructions and Warnings

To ensure safe operation and prevent injury or damage, please adhere to the following guidelines:

General Safety

  • Do not allow children to operate this product. Users with physical, sensory, or psychological disorders, or those lacking knowledge of the product's functions, must be supervised by a fully competent user.
  • This product is designed for cleaning framed windows and glass only. It is not suitable for frameless windows or glass.
  • If the window or glass frame has a damaged silicone rubber edge, exercise caution as the machine may leak and fall off.
  • Always use the original adapter provided with the product. Using a non-original adapter may cause product failure or damage.
  • Ensure adequate ventilation and heat dissipation for the adapter during use. Do not wrap the power adapter.
  • Do not use the adapter in a humid environment or touch it with wet hands.
  • Charge the window cleaner at the voltage the power adapter can withstand.
  • Do not use a damaged power adapter, charging cable, or power plug.
  • Before cleaning or maintaining the machine, unplug the power plug. Do not disconnect power by unscrewing the extension cord.
  • Do not disassemble the power adapter. If faulty, replace the entire adapter. Contact customer service for assistance.
  • The product battery poses a risk of combustion or chemical injury if not handled properly. Do not disassemble the battery or expose it to fire or temperatures above 60°C.
  • Dispose of used batteries at a local professional waste battery product recycling center in accordance with national laws.
  • Do not immerse this product in liquids (e.g., beer, water, drinks) or leave it in a humid environment for extended periods.
  • Keep this product away from direct sunlight and heat sources (e.g., radiators, heaters, microwave ovens, gas stoves).
  • Do not place this product in a strong magnetic field.
  • Store this product out of reach of children.
  • Use this product within an ambient temperature range of 0°C to 40°C (32°F to 104°F).
  • Do not clean damaged glass or objects with uneven surfaces, as this may prevent sufficient vacuum suction.
  • The built-in battery can only be replaced by the manufacturer or designated service center.
  • Disconnect power before removing or handling the battery.
  • The manufacturer is not responsible for property damage or personal injury caused by improper use.

Risk of Electric Shock

  • Ensure the power is completely disconnected and the machine is off before cleaning or maintaining the body.
  • Do not drag the power plug by the extension cord; unplug it properly.
  • Discontinue use if the machine or power supply is damaged. Contact your local after-sales center for repair.
  • Do not use water to clean the machine body or power adapter.
  • Do not use this product in dangerous areas such as open flames, bathrooms with flowing water, or near swimming pools.
  • Do not damage or twist the power cord. Avoid placing heavy objects on the power cord or adapter.

Operational Warnings

  • Before operation, attach the safety rope securely to the machine and a stable indoor object to prevent falls.
  • Before turning on, check the safety rope for damage and secure knotting.
  • When cleaning glass without a blocking table, set up a safety warning area downstairs.
  • Fully charge the built-in backup battery before use (green light on).
  • Do not use in rainy or wet weather.
  • Turn on the machine first, then place it on the window glass.
  • Ensure the machine is safely attached to the window surface before releasing your hands.
  • Before turning off the machine, hold it to prevent dropping.
  • Do not use this product to clean frameless windows or glass.
  • Ensure the cleaning cloth is properly attached to the bottom to prevent air leakage.
  • Do not spray water directly on the machine or its bottom; spray water only on the cleaning cloth.
  • Remove any items from the glass surface before use.
  • Keep hair, loose clothes, fingers, and other body parts away from working parts.
  • Do not use the machine in areas with flammable or explosive solids or gases.

Specifications

Product specifications and dimensions diagram

Image: Diagram illustrating the product's dimensions and key specifications.

FeatureSpecification
Model NumberYTK-02
Brand NameDIVEDEER
OriginMainland China
CertificationROHS
Input VoltageAC100-240V 50Hz-60Hz
Adapter Voltage24V, 3.75A
Rated Power80W
Motor TypeBrushless motor
Suction Power2800Pa
Cleaning Speed4 mins/m²
Built-in Battery650mAh
Battery Backup Time40 minutes
Noise Level65-70dB
External Dimensions295 x 145 x 68 mm
Net Weight1.03KG
Water Tank Capacity50ml
Water Spraying MethodManual / Auto, Single nozzle, ultrasonic water spray
Control MethodRemote control (2.4G / infrared)
Border DetectionAutomatic (for framed glass)
Fall Arrest ControlPower failure protection (backup battery) safety rope
Cleaning Modes3 Intelligent path planning modes
Included Cleaning Cloths10 PCS

Product Components and Accessories

Product detail drawing with numbered parts

Image: Detailed diagram of the robot's components, including water tank, one-button start, remote control receiving window, power socket, safety rope hanging hole, power interface, and indicator lights.

Product Main Body & Accessories list

Image: Visual representation of the main unit and all included accessories, such as cleaning rings, cleaning cloths, adapter, power cord, safety rope, user manual, water bottle, and remote control.

Power Light Indicators

  • Orange light: Charging
  • Blue light: Machine is normal
  • Green light: Charging complete
  • Red light: Machine abnormality

Setup

1. Power Connection

  1. Connect the AC power cord to the adapter.
  2. Insert the threaded connector into the power connector of the robot fuselage and tighten it.
  3. Plug the power cord into a suitable socket.
  4. Ensure the built-in battery is fully charged before use (indicated by a green light). If the orange light is on, it is charging.
Power connection diagram

Image: Step-by-step diagram showing how to connect the power adapter and cord to the robot.

2. Install the Cleaning Cloth and Ring

  1. Place the cleaning cloth onto the cleaning ring.
  2. Correctly attach the cleaning ring with the cloth onto the cleaning wheel of the robot to prevent air leakage.
Cleaning cloth installation diagram

Image: Diagram illustrating the correct method for installing the cleaning cloth and ring onto the robot.

3. Attach a Safety Rope

  1. For glass doors and windows without a balcony below, set up a danger warning area on the ground to prevent people from approaching.
  2. Before using, check the safety rope for any damage and ensure the knot is secure.
  3. Fasten the safety rope to a fixed object indoors to prevent the robot from falling.

4. Water Tank Filling

  1. Do not add any cleaning agents other than clean, impurity-free water to the water tank.
  2. Open the silicone cover and add clean water.
  3. Do not overfill the water tank; 80% capacity is sufficient to maintain stable air pressure.
Water tank filling diagram

Image: Diagram showing how to open the silicone cover and fill the water tank.

5. Attaching the Machine to Glass

  1. Press and hold the power button for 2 seconds to turn on the robot. Confirm that the fan rotates.
  2. Place the machine onto the glass surface, maintaining a certain distance from the window frame.
  3. Ensure the machine is securely attached to the glass before releasing your hands.
Attaching to glass diagram

Image: Diagram illustrating the process of turning on the robot and attaching it to the glass surface.

Operating Instructions

1. Dry Wipe

For the first wipe, perform a dry wipe without spraying water to remove loose sand and dirt from the glass surface. If water or detergent is sprayed initially, it may mix with sand and create a muddy residue, reducing cleaning effectiveness. Dry wiping is most effective in sunny or low-humidity conditions.

Dry wipe diagram

Image: Diagram showing the robot performing a dry wipe on a window.

2. Wet Wipe

The robot has one water nozzle for spraying water during cleaning.

  • Automatic Water Spray: In auto cleaning mode, press the "AU" button on the remote control. The machine will beep twice, and automatic water spray will begin intermittently. Press "AU" again to turn off the automatic spray (one beep).
  • Manual Water Spray: In auto cleaning mode, press the water spray button on the remote control once to spray water once.
Wet wipe diagram

Image: Diagram showing the robot performing a wet wipe with water spray.

3. Intelligent Path Planning Modes

The robot offers three intelligent path planning modes for efficient cleaning:

  • Mode 1: Automatic cleaning up and then down.
  • Mode 2: Auto clean first left and then down.
  • Mode 3: Auto clean first right and then down.
3 Intelligent path planning modes diagram

Image: Diagram illustrating the three intelligent path planning modes for window cleaning.

4. Remote Control Functions

The remote control allows you to manage the robot's movements and functions. It can receive signals from both the front and back of the robot.

Remote control image

Image: The remote control unit, showing various buttons for directional movement, cleaning modes, and water spray functions.

Button/FunctionDescription
Auto clean up and then downInitiates cleaning in an up-and-down pattern.
Manual upward movementMoves the robot upwards manually.
Auto clean left and then downInitiates cleaning starting from the left, then moving downwards.
Manual downward movementMoves the robot downwards manually.
Auto clean right and then downInitiates cleaning starting from the right, then moving downwards.
Manually move to the rightMoves the robot to the right manually.
Automatic water spray (AU)Toggles intermittent automatic water spray.
Manual move leftMoves the robot to the left manually.
Manual water spraySprays water once per press.
Start/PauseStarts or pauses the cleaning operation.

Remote Control Battery: Do not charge, disassemble, or put the remote control battery in fire. Use AAA/RL batteries of the same specification. Do not mix new and old batteries or different types. When installing, align the negative pole with the spring first, press it down, then cover the battery cover.

Power Failure Protection (Backup Battery)

In the event of a sudden power failure, the robot's built-in backup battery will activate. This battery can supply power for up to 40 minutes (when fully charged) to prevent the machine from falling off the glass. During a power failure, the machine will remain in place, emit a warning sound, and the red/blue lights will flash alternately. It will not move forward.

If a power failure occurs, gently pull the device back using the safety rope, keeping it as close to the glass as possible to avoid falling. Reconnect the power adapter properly for the machine to resume operation.

Power failure protection diagram

Image: Diagram illustrating the robot's behavior during a power failure, showing it remaining attached to the glass.

Maintenance

1. Cleaning Cloths

  • If the cleaning cloth is too dirty, replace it with a clean one.
  • After cleaning, remove the cleaning cloths from the rings and wash them.

2. Ultrasonic Nozzle

  • If the machine is not spraying water, clean the ultrasonic nozzle with a clean, soft cloth.

3. Water Tank

  • Ensure the water tank contains water and that the added cleaning solution (if any) is clean and pure.

4. Cleaning Wheels

  • If the screw of a cleaning wheel is loose, lock it. Do not overtighten, as this may affect the glass glue thickness or beveled window frame performance.

5. Storage

  • After cleaning is completed and the robot is removed from the window, untie the safety rope.
  • Store the machine and its related accessories in a dry and ventilated environment for future use.

Troubleshooting

If you encounter any issues with your window cleaning robot, refer to the following troubleshooting guide:

  • Machine runs slowly or fails during first use (especially on dirty outer windows):
    A. Clean and dry the supplied cleaning cloth before use.
    B. Spray a little water or glass cleaner evenly on the cleaning cloth or the glass surface.
    C. After dampening and wringing out the cleaning cloth, put it into the cleaning ring.
  • Machine tests itself at startup, makes warning sound, or doesn't run smoothly (friction too large/small):
    A. Check if the cleaning cloth is too dirty.
    B. If using glass stickers or fog stickers, their friction coefficient may be too low.
    C. If the glass is very clean, it might be too slippery.
    D. In low humidity (e.g., air-conditioned rooms), the glass may become too slippery after multiple wipes.
  • Machine cannot detect the upper edge of the window after pressing the up automatic cleaning button:
    Press the appropriate key to switch to a different auto clean mode.
  • Machine cannot wipe the upper left side of the glass:
    Use the remote control's manual window cleaning mode to clean this area. This can occur if the glass or cleaning cloth is slippery, the wiped glass width is larger, or the top line slides slightly.
  • Machine doesn't clean windows completely or finishes early:
    Press the appropriate button or use auto window mode to continue the unfinished cleaning.
  • Machine slips or doesn't climb:
    A. Friction is too small (e.g., with certain stickers).
    B. The cleaning cloth is too wet, or the glass is very clean and slippery.
    C. Low humidity can make the glass too slippery.
    D. If starting the machine too close to the window frame, it might cause incorrect judgment. Place the machine at a distance from the frame.
  • Round wheel marks remain on the glass surface after cleaning:
    The cleaning cloth is too dirty. Replace it with a clean cloth and wipe again.
  • Machine doesn't run smoothly:
    A. The cleaning cloth is too dirty; replace it.
    B. Different areas on the glass surface (e.g., glass area, sticker area) can affect performance. Use it in a single area.
    C. If the screw of the cleaning wheel is loose, lock it (do not overtighten).
  • Warning sound and red light flashing when machine stops due to power failure:
    A. Gently pull the safety rope back to the machine, keeping it close to the glass.
    B. Turn off the machine power switch.
    C. Check the wire for poor contact or breakage.
  • Machine stops when encountering unknown obstacles (red light flashes, no warning sound):
    A. Move the machine back to a safe position via remote control or by gently pulling the safety rope.
    B. Remove any obstacles from the window.
    C. Check for air leaks.
  • Arc marks on polished glass when light shines at night:
    For the first time, turn off the water spraying function and use a clean cloth to remove sand. For the second wipe, clean and replace the cloth, turn on water spraying, or keep the upper cleaning wheel clean/dry and spray a little detergent/alcohol on the lower cleaning wheel (1-2 sprays).
  • Machine cleans all windows but doesn't stop automatically:
    Press the stop key to end the operation.
  • Machine will not spray water:
    A. Confirm the water spray function switch is on.
    B. Clean the ultrasonic nozzle with a clean soft cloth.
    C. Check the water tank for water and ensure the cleaning solution is clean and pure.

User Tips

  • Initial Startup: After turning on the robot, wait 20 seconds until the blue light stops flashing. This allows the robot to detect the glass surface before starting operation.
  • Safety First: Always bind the safety rope securely when using the robot to prevent it from falling from high altitudes.
  • Enhanced Cleaning: For better cleaning results, spray some water on the edge of the mop before or during operation.
  • Power Connection: The machine must be connected to a power adapter to work properly. The internal battery is a backup for safety during power outages, not for charging or cordless operation.
  • Noise Level: The robot produces a normal operating noise of around 65-70 decibels. If you are sensitive to noise, please consider this before use.

Warranty and Support

We offer a 1-year warranty for the robot. If any damage occurs, we will provide replacement parts free of charge, along with an installation video to guide you. Please note that if the damage is artificially caused, a fee may apply for parts or service.

For further detailed instructions, diagrams, and additional support, please refer to the official User Manual (PDF) available at https://manuals.plus/m/b0bfa70a56aba40769d36f15e7115d1d6fea52c7fe9efe6f0214adb306e5f6c0.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.