HSP 94111

Contents

HSP 94111 1/10 4WD Electronic Powered Brushed Motor RTR RC Truck

Model: 94111 | Brand: HSP

1. Introduction

Thank you for purchasing the HSP 94111 1/10 4WD Electronic Powered Brushed Motor RTR RC Truck. This Ready-To-Run (RTR) model is designed for enthusiasts seeking a powerful and durable remote-controlled vehicle. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your RC truck to ensure a safe and enjoyable experience.

HSP 94111 RC Truck and 2.4GHz remote controller
Figure 1: HSP 94111 RC Truck and 2.4GHz Remote Controller

2. Safety Warnings

  • WARNING: Not suitable for children under 36 months. This product contains small parts and is intended for users aged 14 years and older.
  • Always operate the RC truck in open areas, away from people, pets, and obstacles.
  • Never operate the RC truck near public roads, water, or high-voltage power lines.
  • Keep fingers, hair, and loose clothing away from moving parts such as wheels and gears.
  • Do not touch the motor or ESC immediately after use, as they can become very hot.
  • Always disconnect the battery from the truck when not in use and during charging.
  • Use only the provided charger and battery, or compatible replacements recommended by the manufacturer.
  • Never leave charging batteries unattended.

3. Package Contents

The HSP 94111 RC Truck package includes the following items:

  • 1 x HSP 94111 1/10 4WD Electronic Powered Brushed Motor RTR RC Truck
  • 1 x 2.4GHz Transmitter (Remote Controller)
  • 1 x 7.2V 1800mAh Ni-MH Battery Pack
  • 1 x Battery Charger (EU Plug)
  • 1 x English Instruction Manual
EU standard battery charger
Figure 2: Included EU Standard Battery Charger
7.2V 1800mAh Ni-MH battery pack
Figure 3: 7.2V 1800mAh Ni-MH Battery Pack
2.4GHz remote controller (transmitter)
Figure 4: 2.4GHz Remote Controller

4. Specifications

FeatureSpecification
BrandHSP
Model Number94111
Scale1:10
TypeRC Truck
Drive System4 Wheel Drive
MotorRC540 Brushed Motor
ESCSP03018 (60A constant, 300A burst, 150A backward, 300A forward)
Steering ServoE6001 (3Kg.cm at 7.2V, 0.12sec/60° at 7.2V)
Throttle Servo3Kg.cm at 7.2V
Battery7.2V 1800mAh Ni-MH
Charging Voltage7.2V
Remote ControlYes, 2.4GHz
Control Channels2 CHANNELS
Controller ModeMODE2
Remote DistanceAbout 150m
Length400mm
Width300mm
Height160mm
Wheelbase275mm
Ground Clearance32mm
Wheels118 * 52mm
Weight1530g
Chassis TypePlastic
ShocksOil Filled Capped
MaterialPlastic
Recommended Age14+y
HSP 94111 RC Truck with body removed, showing chassis and components
Figure 5: Internal components of the HSP 94111 RC Truck
Close-up of the Electronic Speed Controller (ESC) and receiver with wiring
Figure 6: ESC and Receiver Unit
Close-up of the RC540 brushed motor with purple heatsink
Figure 7: RC540 Brushed Motor with Heatsink
Close-up of the steering servo (E6001) and receiver unit
Figure 8: E6001 Steering Servo and Receiver

5. Setup

5.1 Charging the Battery

  1. Connect the included 7.2V 1800mAh Ni-MH battery pack to the charger.
  2. Plug the charger into a suitable power outlet (EU standard).
  3. Allow the battery to charge fully. Refer to the charger's indicator lights for charging status. Do not overcharge.
  4. Once charging is complete, disconnect the battery from the charger.

5.2 Installing the Battery in the Truck

  1. Remove the body shell of the RC truck by detaching the body clips.
  2. Locate the battery compartment on the chassis.
  3. Insert the charged 7.2V Ni-MH battery pack into the compartment.
  4. Connect the battery connector to the ESC/power connector on the truck. Ensure the polarity is correct.
  5. Secure the battery in place, typically with a battery strap or tray cover.
  6. Reattach the body shell.

5.3 Transmitter Setup

  1. Open the battery compartment on the bottom of the 2.4GHz transmitter.
  2. Insert 4 AA batteries (not included) into the compartment, observing correct polarity.
  3. Close the battery compartment cover.
  4. Turn on the transmitter. The indicator light should illuminate.

5.4 Binding (If Necessary)

Your HSP 94111 is a Ready-To-Run (RTR) model and should come pre-bound from the factory. If for any reason the truck and transmitter lose connection, follow these general binding steps:

  1. Ensure both the transmitter and the truck's battery are fully charged.
  2. Turn on the transmitter first.
  3. Connect the truck's battery and turn on the truck's power switch (usually located on the ESC).
  4. Observe the receiver's LED. It should become solid, indicating a successful bind. If it flashes, consult the specific binding instructions in the included manual or the manufacturer's website.
  5. Test the steering and throttle controls to confirm functionality.

6. Operating Your RC Truck

6.1 Basic Controls

  • Steering Wheel: Turn left or right to control the truck's direction.
  • Throttle Trigger: Pull to accelerate forward, push to brake/reverse.
  • Steering Trim: Adjusts the neutral position of the steering. If the truck pulls left or right when the steering wheel is centered, use this trim to correct it.
  • Throttle Trim: Adjusts the neutral position of the throttle. If the truck moves forward or backward when the trigger is neutral, use this trim to correct it.

6.2 Driving Tips

  • Start slowly to get a feel for the controls before attempting high speeds.
  • Avoid driving in wet conditions or through deep puddles, as this can damage electronics.
  • Be mindful of battery life. When the truck starts to slow down significantly, it's time to recharge the battery.
  • Practice in an open, clear area to develop your driving skills.
  • The 4WD system provides excellent traction; experiment with different terrains.

7. Maintenance

7.1 After Each Run

  • Turn off the truck and transmitter. Disconnect the battery from the truck.
  • Clean the truck: Remove dirt, dust, and debris from the chassis, suspension, and motor using a soft brush or compressed air.
  • Inspect for damage: Check for loose screws, bent parts, or damaged wires.
  • Check tires: Ensure tires are securely mounted and not excessively worn.

7.2 Regular Maintenance (Every 3-5 Runs)

  • Lubricate moving parts: Apply a small amount of RC-safe lubricant to gears, bearings, and pivot points.
  • Check shock absorbers: Ensure they are not leaking and provide consistent damping.
  • Inspect drivetrain: Check drive shafts and differentials for wear or damage.
  • Battery care: Store Ni-MH batteries in a cool, dry place. Do not store fully charged or fully discharged for extended periods.
Close-up of the oil-filled shock absorber and suspension arm
Figure 9: Oil-filled Shock Absorber

8. Troubleshooting

ProblemPossible CauseSolution
Truck does not respondLow battery in truck or transmitter; Not powered on; Not boundCharge/replace batteries; Ensure power switches are ON; Re-bind transmitter and receiver.
Poor range or intermittent controlInterference; Loose antenna wire; Low transmitter batteryMove to a different location; Check antenna connections; Replace transmitter batteries.
Steering not centeredSteering trim incorrect; Servo horn looseAdjust steering trim on transmitter; Check servo horn for tightness.
Motor runs but wheels don't turnStripped gears; Loose wheel nuts; Broken drivetrain componentInspect gears (pinion/spur); Tighten wheel nuts; Check drive shafts and differentials.
Truck runs slowly or lacks powerLow truck battery; Motor/ESC overheating; Excessive frictionRecharge truck battery; Allow components to cool; Check for binding in drivetrain/wheels.

9. User Tips

  • Consider upgrading to a LiPo battery and compatible charger for longer run times and increased power, ensuring compatibility with the ESC.
  • Regularly check all screws and fasteners, especially after aggressive driving, as vibrations can cause them to loosen.
  • Keep spare parts like body clips, gears, and suspension arms on hand for quick repairs.
  • For optimal performance, ensure your tires are clean and free of debris before each use.

10. Warranty and Support

This product comes with a 1-month warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.

For technical support, spare parts, or warranty inquiries, please contact the seller or manufacturer directly. Refer to your purchase documentation for contact information.

© 2023 HSP. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.