GODIAG GT105 II

Contents

GODIAG GT105 II ECU IMMO Prog AD OBD2 Break Out Box

User Manual

1. Introduction

The GODIAG GT105 II ECU IMMO Prog AD is a versatile OBD2 breakout box designed for automotive diagnostic and programming applications. It facilitates IMMO activation matching, ECU diagnosis, and programming connections. This device can draw power directly from the vehicle's battery, making it suitable for outdoor on-site vehicle maintenance.

The GT105 II is an enhanced version of the GT105, featuring five additional functions:

  • Vehicle voltage display
  • Car remote control battery CR2032 battery test
  • Car battery voltage alarm prompt (activates if voltage drops below 11V)
  • TOYOTA steering angle matching
  • Lamborghini ID48 key IMMO auxiliary activation

It is equipped with signal communication indicators for PWM+(PIN2), CANH(PIN6), CANL(PIN14), and K-line(PIN7). These indicators flash during data communication, allowing users to monitor the communication status and confirm if the diagnostic programming device is communicating correctly.

2. Key Features and Functions

2.1. Product Highlights

  • Full-protocol ECU connection line for ECU programming power adjustment.
  • OBD2 independent PIN4 body GND and PIN5 signal GND for special programming of certain modules.
  • PIN4 and PIN5 can be switched between short-circuit and non-short-circuit configurations.
  • Standard OBD2 independent PIN4 and PIN5.
  • Pure copper female seat design ensures durability and long service life through repeated insertions and removals.
  • Battery clips are treated with an environmentally-friendly salt spray, with a thickness of 0.5mm, for enhanced corrosion resistance.
  • The DC car battery cable uses a 0.75mm² 2-core sheathed cable, supporting DC5.5*2.5 and DC5.5*2.1 interfaces.
  • The DC connector includes a resettable 7A fuse for protection.
  • Dedicated DC power interface for laboratory power connections.

2.2. Product Functions

  • Vehicle Voltage Display: Shows the current vehicle battery voltage.
  • Car Remote Control Battery CR2032 Test: Tests the voltage of CR2032 batteries commonly found in car remote controls.
  • Car Battery Voltage Alarm: Alerts the user if the car battery voltage drops below 11V.
  • TOYOTA Steering Angle Matching: Supports matching for TOYOTA steering angles.
  • Lamborghini ID48 Key IMMO Auxiliary Activation: Assists in the activation of ID48 keys for Lamborghini vehicles.
  • IMMO AD Power Adapter: Functions as a power adapter for IMMO systems. Post-2016 Ford smart keys can be programmed in conjunction with VVDI equipment (OBDSTAR, AUTEL) and other anti-theft matching tools.
  • All Car Keys Lost Matching: Can wake up the meter or anti-theft ECU for key matching. Supports VAG 4th and 5th generation anti-theft systems, Toyota ECU synchronization, Mitsubishi all key lost matching, remote control key setting, and IMMO key learning for older Porsche Cayenne models.
  • Communication Protocol Indicators: VPW, CANH, CANL, and K-Line indicator lights provide visual feedback on communication status between the vehicle and the diagnostic programming device.
  • On-site Maintenance Power Supply: The GT105 II power adapter cable draws 12V from the car battery to power programming equipment (e.g., Xhorse Key Tool Plus Pad, VVDI Prog, CGDI Prog, IM608) for outdoor data reading and ECU maintenance.
  • Key Cutter Power Supply: Provides a 12V power supply for key cutting devices.
  • OBD Battery Replacement Tool: Ensures uninterruptible power supply during battery replacement, preventing data loss, key failure, or re-matching issues. Benefits include: clock remains unchanged, speaker not locked, IMMO not locked, glass door not set, throttle not set, warning light off, and no fault codes.

3. Package Contents

The standard package for the GODIAG GT105 II includes:

  • 1pc x GODIAG GT105 II Host
  • 1pc x Power Cord with Battery Clip

Note: The OBD2 full protocol ECU programming line is an optional accessory and must be purchased separately.

GODIAG GT105 II device with included accessories: power cable, alligator clips, and product box.

Figure 1: GODIAG GT105 II and included accessories

4. Specifications

AttributeValue
Brand NameGODIAG
Model Namegt105 II
Hardware VersionGT105 II
Software VersionCABLE
Item TypeElectrical Testers & Test Leads
MaterialPlastic
OriginMainland China
External Testing CertificationCE
Item Weight0.2kg
Item Height11cm
Item Width25cm
Item Length29cm
Guarantee1 year

Video 1: GODIAG GT105 II Product Overview

5. Setup

The GODIAG GT105 II is designed for easy connection to vehicle OBD2 ports and external ECUs. Follow these general steps for setup:

5.1. Connecting to Vehicle OBD2 Port

  1. Locate the vehicle's OBD2 diagnostic port, typically found under the dashboard on the driver's side.
  2. Plug the GT105 II directly into the OBD2 port. Ensure a secure connection.
  3. The device will draw power from the vehicle's battery. The vehicle voltage will be displayed on the GT105 II's screen.
GODIAG GT105 II connected to a car's OBD port.

Figure 2: GT105 II connected to a vehicle's OBD port

5.2. Connecting for ECU Programming and External Power

For ECU programming or when an external power source is required, use the provided power cord with battery clips or an optional ECU programming cable.

  1. Connect the power cord with battery clips to the DC power input on the GT105 II.
  2. Attach the red alligator clip to the positive (+) terminal of the car battery and the black alligator clip to the negative (-) terminal.
  3. If using an external regulated power supply for ECU programming, connect it to the DC power interface of the GT105 II.
  4. Connect the GT105 II to the ECU using the appropriate cables (e.g., optional OBD2 full protocol ECU programming line) and any necessary matching adapters.
Wiring diagram showing GODIAG GT105 II connected to an ECU, a regulated power supply, and a key matching adapter.

Figure 3: Wiring diagram for ECU programming setup

6. Operating Instructions

6.1. Monitoring Vehicle Voltage and Battery Status

  • Once connected to the vehicle's OBD2 port, the GT105 II will automatically display the current vehicle voltage on its digital screen.
  • If the vehicle battery voltage drops below 11V, the device will trigger an alarm.
  • To test a CR2032 remote control battery, connect it to the designated test points on the device (refer to the device's labels for specific points).

6.2. Using Communication Protocol Indicators

The GT105 II features LED indicators for various communication protocols (PWM+, CANH, CANL, K-Line). When data communication occurs on a specific protocol, its corresponding LED indicator will flash. This allows you to:

  • Visually confirm active communication between the vehicle and your diagnostic tool.
  • Determine if your diagnostic programming device is successfully sending or receiving data.

6.3. IMMO and ECU Programming Functions

The GT105 II acts as an interface for various IMMO and ECU programming tasks:

  • IMMO Activation Matching: Use in conjunction with compatible diagnostic tools for IMMO system activation and key matching.
  • ECU Diagnosis and Programming: Connect to ECUs for diagnostic procedures and programming operations.
  • Key Programming: Supports programming for various vehicle types, including Ford smart keys (post-2016 with VVDI, OBDSTAR, AUTEL), VAG 4th/5th generation anti-theft, Toyota ECU synchronization, Mitsubishi all key lost, and Porsche Cayenne IMMO key learning.
  • PIN4/PIN5 Switching: Utilize the switch function to alternate between short-circuit and non-short-circuit modes for PIN4 and PIN5 as required by specific programming procedures.

6.4. OBD Battery Replacement Tool

When replacing a vehicle's battery, connect the GT105 II to the OBD2 port and an external 12V power source (e.g., another car battery via the provided clips) to maintain continuous power to the vehicle's systems. This prevents:

  • Loss of clock settings.
  • Locking of the speaker system.
  • IMMO system locking.
  • Resetting of glass door settings.
  • Resetting of throttle settings.
  • Activation of warning lights.
  • Generation of fault codes.

7. Maintenance

  • Keep the device clean and free from dust and moisture.
  • Store the device in a dry, cool place when not in use.
  • Avoid dropping or subjecting the device to strong impacts.
  • The pure copper female seats are designed for long-term durability; however, ensure proper alignment when connecting cables to prevent damage.
  • The battery clips are treated for corrosion resistance, but it is good practice to wipe them clean after use, especially if they come into contact with battery acid or other corrosive substances.

8. Troubleshooting

  • No Power/Display: Ensure the device is securely connected to the vehicle's OBD2 port or an external 12V power source. Check the power cord and battery clip connections. Verify the vehicle battery has sufficient charge.
  • No Communication Indication: If the protocol indicator lights are not flashing during an operation, check all cable connections between the GT105 II, the vehicle/ECU, and the diagnostic programming device. Ensure the diagnostic device is correctly configured and functioning.
  • Voltage Alarm Constantly On: If the car battery voltage alarm is active, it indicates the vehicle's battery voltage is below 11V. Charge or replace the vehicle battery as necessary before proceeding with operations that require stable power.
  • Device Overheating: Disconnect the device immediately if it feels excessively hot. Check for any short circuits in the wiring or connected components. The DC connector has a resettable 7A fuse for protection against overcurrent.

9. Warranty and Support

The GODIAG GT105 II comes with a 1-year guarantee from the date of purchase. For technical support, troubleshooting assistance, or warranty claims, please contact your vendor or the official GODIAG support channels.

A detailed user manual in PDF format is available for download: GODIAG GT105 II User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.