IRALAN BY-601-500-1

Contents

IRALAN Modern Ceiling Fan with Lights and Remote Control User Manual

Model: BY-601-500-1 | Brand: IRALAN

1. Safety Information

READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE FAN AND SANE INSTRUCTIONS.

  1. To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.
  2. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
  3. The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9 kg). Use only UL Listed outlet boxes marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less".
  4. The fan must be mounted with a minimum of 7 ft. (2.1 m) clearance from the trailing edge of the blades to the floor.
  5. Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.
  6. Do not place objects in the path of the blades.
  7. To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.
  8. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches. Refer to the instructions packaged with the light kits and switches for proper assembly.
  9. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
  10. All setscrews must be checked and re-tightened where necessary before installation.

WARNING:

  • To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
  • To reduce the risk of fire or electric shock, this fan is NOT suitable for use with solid-state speed controls.
  • To avoid possible electrical shock, make sure that the electricity is turned off at the main power box before starting work. If you feel you do not have enough electrical wiring knowledge or experience, contact a licensed electrician.
  • Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan.
  • To reduce the risk of fire, electrical shock or personal injury, ensure that the fan mounting bracket is supported directly from the building structure or the outlet box marked "Acceptable for Fan Support of 35 lbs. (15.9 kg) or less". Use only the screws provided with the outlet box.

2. Package Contents

The package includes the following components:

  • Fan-motor assembly (1)
  • LED light kit (1)
  • Lamp panel (1)
  • Acrylic sheet (1)
  • Inside canopy (5)
  • Blade (3)
  • 10 CM Ball/downrod assembly (1)
  • Canopy (1)
  • 20CM Ball/downrod assembly (1)
  • Coupling cover (1)
  • Remote control (Transmitter) (1)
  • Remote control (Receiver) (1)

Hardware included:

  • Blade attachment screw and fiber washer (6)
  • Tapping Screws (4)
  • Expansion Bolts (2)
IRALAN Ceiling Fan with Remote Control
IRALAN Ceiling Fan with Remote Control (Black variant shown)

3. Tools Required

The following tools are required for installation:

  • Phillips screwdriver
  • Flat blade screwdriver
  • Step ladder
  • Drill
  • Wrench

4. Specifications

AttributeValue
Brand NameIRALAN
Model NumberBY-601-500-1
Item TypeCeiling Fans
Size (42 inch)105*105*15.8 /25.8 CM
Size (52 inch)132*132*15.8 /25.8 CM
Downrods Available10cm and 20cm
Blade Color OptionsBlack, White
Body MaterialABS, aluminum, Iron
StyleModern Style
Power SourceAC
Input Voltage85-265V
Motor Power30W
LED Power18W
Light SourceLED bulbs
Is DimmableYes (Infinitely adjustable lighting, 3 color temperatures: 3000K, 4000K, 6000K)
Luminous Flux2000-82000
Number of Lights>8
Is Bulbs IncludedNo
Base TypeWedge
Control MethodRemote Control
Switch TypeRemote Control
Wind Speed6 Gears
FeaturesInfinitely adjustable lighting, Reversible DC Motor (Summer/Winter mode)
Application Space10-20㎡
Installation MethodAssembly
FinishSpray Paint
Weight4.2KG
CertificationCCC, CE
Warranty2 Years
Dimensions and Specifications
Detailed dimensions and electrical specifications

5. Setup and Installation

Please ensure power is OFF at the circuit breaker before beginning installation.

5.1. Mounting Hanger (Hanging Part)

For Wooden Ceiling:

Use wood screws to drill on the wooden beam or the "junction box" to fix the hanging bracket. Selection is made according to actual requirements of the customers.

  1. Switch OFF the electrical mains at the circuit breaker fuse box.
  2. Use the Mounting Bracket (A) as a guide, mark the spots where the 4 Self Tapping Screws (B) will be drilled.
  3. Remove the Mounting Bracket (A), drill 4 holes for 3MM diameter, install the mounting bracket onto wooden ceiling with the 4 Self Tapping Screws (B).

▲ IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG

For Concrete Ceiling:

Use a percussion bit with diameter 8mm to drill holes according to the length of expansion screws. Then use the attached expansion screws to fix the hanging bracket onto the ceiling. Selection is made according to actual requirements of the customers.

  1. Switch OFF the electrical mains at the circuit breaker fuse box.
  2. Use the Mounting Bracket (A) as a guide, mark the spots where the 2 Expansion Bolts (B) will be drilled.
  3. Remove the Mounting Bracket (A). Drill 2 holes for 8MM diameter and insert 2 Expansion Bolts (B) into the concrete ceiling, install the mounting bracket and secure with Flat Washers (C), Spring Washers (D) and Nuts (E).

▲ IMPORTANT: SCREWS MUST BE TIGHTENED TILL SNUG

5.2. Install the Downrod

  1. Insert the canopy and the Bolt & Pin cover onto the downrod. Carefully feed motor wires through the downrod assembly.
  2. Slide the ball down the downrod.
  3. Put the round latch in.
  4. Replace the hanger ball at its normal position.
  5. Secure the two screws.

5.3. Attaching the Fan Blades

  1. Remove 6 screws from the motor.
  2. Attach the blades to the motor using the removed screws. Ensure the side marked "THIS SIDE UP" faces upwards.

5.4. Attaching the Light Kit

CAUTION: To reduce the risk of electric shock, disconnect the electrical circuit to the fan before installing the light fixture.

  1. Remove three screws from the plate on the motor.
  2. Use these three screws to assemble the light kit fitter.
  3. Connect the light source and lock it to the lamp tray with three screws.
  4. Install the acrylic sheet.

5.5. Installing Remote Control Receiver and Wiring

WARNING: Turn off the electric power during installation and making wire connection.

  1. Once wiring step has been completed, slide the wired remote receiver in between the mounting bracket and the top of the downrod ball for downrod fans.
  2. Connect the wire from the ceiling fan into the receiver.
  3. Connect the wire from the receiver with the wire from the house.

Wiring Diagram:

From CEILING FAN to Receiver: Connect the fan wires to the receiver.

From Receiver to House: Connect the receiver wires to the house wiring.

  • Brown wire: FOR DC IN L
  • Blue wire: FOR DC IN N

5.6. Install the Canopy

  1. Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
  2. Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.
Official installation video for the IRALAN Ceiling Fan.

6. Operating Instructions

6.1. Remote Control Functions

The remote control allows you to manage various fan and light settings:

  • NO/OFF: Power on/off the fan and light.
  • Wind speed 1-6 gear: Adjust fan speed from 1 (low) to 6 (high).
  • Increased brightness: Increase light brightness.
  • Reduced brightness: Decrease light brightness.
  • Fan forward/reverse switch: Change fan direction for summer (downward airflow) or winter (upward airflow) modes.
  • General (turn off all functions): Turn off all active functions.
  • Turn off the fanCode: Disconnect the fan from the remote control.
  • Increased color temperature: Adjust light to cooler tones (e.g., white).
  • Lower color temperature: Adjust light to warmer tones (e.g., warm).
  • Natural Wind: Activate natural wind mode.
  • 2-hour time: Set a 2-hour timer for the fan/light.
  • Night light: Activate a low-intensity night light mode.

Note: The remote control must match the same code as the receiver.

Dimmable LED Light Options
Dimmable LED Light: Select from 3 Colors (Warm, Natural, White) with 0%-100% adjustable brightness.
Reversible Wind Modes
Reverse the Wind Without Touching the Fan: Summer Mode (Downward Airflow) and Winter Mode (Upward Airflow).
Quiet DC Motor
Bring Quiet to New Heights: Ultra Quiet operation at 35dB (whisper level).
High Performance DC Brushless Motor
Higher Performance, More Wind Speeds: Powered by TurboSilent™ with 6 wind speeds and a DC Brushless Motor.

6.2. APP Control

The fan can also be controlled via a mobile application:

  1. Step 1: Scan the QR Code to download and install the app on your phone.
  2. Step 2: Turn on the light and search for the light in the app, then pair them.

App functions include:

  • Buttons to control fan power (1-6 speeds).
  • Changing the color temperature.
  • Power switch (fan on/off).
  • Lamp on/off.

7. Maintenance and Care

WARNING: Make sure the power is off before cleaning your fan.

  • Because of the fan's natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure. It is not necessary to remove the fan from the ceiling.
  • Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning, as this could damage the motor, or the wood, or possibly cause an electrical shock. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing.
  • You can apply a light coat of furniture polish to the wood for additional protection and enhanced beauty. Cover small scratches with a light application of shoe polish.
  • You do not need to oil your fan. The motor has permanently-lubricated sealed ball bearings.

8. Troubleshooting

ProblemSolution
The fan will not start
  • Check the main and branch circuit fuses or breakers.
  • Check the line wire connections to the fan and switch wire connections in the switch housing.
The fan is noisy
  • Ensure all motor housing screws are snug.
  • Ensure the screws that attach the fan blade bracket to the motor hub are tight.
  • Ensure the wire nut connections are not rattling against each other or the interior wall of the switch housing.
  • Allow a 24-hour "breaking in" period. Most noises associated with a new fan disappear during this time.
  • If you are using the Ceiling Fan light kit, ensure the screws securing the glassware are tight. Check that the light bulbs are also secure.
  • Ensure the canopy is a short distance from the ceiling. It should not touch the ceiling.
  • Ensure your outlet box is secure and rubber isolator pads were used between the mounting plate and outlet box.

9. Warranty and Support

9.1. Warranty Information

To obtain warranty service, you must present a copy of the receipt as proof of purchase. All costs of removing and re-installing the product are your responsibility. Damage to any part such as by accident, misuse, improper installation, or by affixing any accessories, is not covered by this warranty.

Because of varying climatic conditions this warranty does not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing, or peeling. Brass finishes of this type give their longest useful life when protected from varying weather conditions. A certain amount of "wobble" is normal and should not be considered a defect.

Servicing performed by unauthorized persons shall render the warranty invalid. There is no other express warranty. Hereby disclaims any and all warranties, including but not limited to those of merchant ability and fitness for a particular purpose to the extent permitted by law. The duration of any implied warranty which cannot be disclaimed is limited to the time period as specified in the express warranty. Some states do not allow a limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

The retailer shall not be liable for incidental, consequential, or special damages arising out of or in connection with product use or performance except as may otherwise be accorded by law. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives specific legal rights, and you may also have other rights which vary from state to state. This warranty supersedes all prior warranties. Shipping costs for any return of product as part of a claim on the warranty must be paid by the customer.

For a detailed user manual in PDF format, please refer to the official document: User manual (PDF)

9.2. After-Sales Support

For any after-sales inquiries, please contact: sxdsltd@163.com

10. User Tips

While no specific user tips were available from reviews or Q&A, general best practices for ceiling fan usage include:

  • Regularly clean fan blades to maintain efficiency and prevent dust buildup.
  • Utilize the reversible motor feature to optimize comfort in both summer and winter.
  • Familiarize yourself with the remote control functions for convenient operation of speed, light, and timers.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.