HGLRC Rekon10 PRO Long Range Frame Kit

Contents

HGLRC Rekon10 PRO V2 Long Range Frame Kit

User Instruction Manual

1. Introduction

The HGLRC Rekon10 PRO V2 Long Range Frame Kit is engineered for demanding long-range FPV missions. This 10-inch quadcopter frame is designed to offer exceptional cruising speeds and superior wind resistance, making it ideal for high-altitude flights and challenging environments. It features a robust construction with significantly beefed-up carbon parts compared to its predecessors.

  • Arms are crafted from durable 8mm carbon plates.
  • Top and bottom plates are 3mm thick for enhanced rigidity.
  • The main body is wider and slightly longer to accommodate larger battery configurations.
  • Dual battery mounting (top and bottom) is recommended for maximizing flight range.

2. Safety Information

Please read and understand all safety warnings before assembling or operating your FPV drone. Failure to follow these instructions may result in damage to the product, property, or serious injury.

  • Always work in a clean, well-lit area.
  • Keep small parts away from children.
  • Use appropriate tools for assembly to prevent damage to components.
  • Ensure all screws are tightened securely but do not overtighten to avoid stripping threads or cracking carbon fiber.
  • Verify correct polarity and connections when installing electronic components (flight controller, ESC, motors, etc.).
  • This product is a frame kit and requires additional electronic components for operation. Refer to the manuals of those components for their specific safety guidelines.

3. Package Contents

Carefully unpack the box and ensure all items listed below are present and in good condition. If any parts are missing or damaged, please contact your retailer.

Carbon Fiber Parts:

  • 1x 3mm top plate
  • 1x 3mm base plate
  • 1x 2mm mid plate
  • 2x 8mm front arm
  • 2x 8mm rear arm
  • 2x 2mm rack protection board
  • 2x 2mm camera side panel

Hardware & Standoffs:

  • 2x M3*30mm black mesh aluminum column
  • 4x M3*20mm black mesh aluminum column
  • 2x M3*18mm black mesh aluminum pillar
  • 4x M4*16 Screws
  • 4x M3*22 Screws
  • 4x M3*20 Screws
  • 4x M3*10 Screws
  • 8x M3*8 Screws
  • 4x M2*20 Screws
  • 1x M2*16 Screws
  • 2x M2*4 Screws
  • 1x M5 lock nut (red)
  • 4x M3 self-locking nuts
  • 5x M2 self-locking nuts
  • 8x M3*8 shock-absorption balls
  • 4x M2*4 shock-absorption balls

Accessories & TPU Parts:

  • 2x battery straps 20x250mm
  • 1x Battery Anti-slip pad
  • 1x Down Battery Anti-slip pad
  • 1x TPU black GoPro holder mount
  • 1x TPU black GPS mount
  • 2x TPU black antenna mount
  • 1x TPU black T-antenna mount
  • 1x TPU black buzzer mount
  • 1x TPU black DJI Air unit Block A
  • 1x TPU Black DJI Air unit Block B
  • 1x TPU black DJI O3 holder mount
Rekon10 PRO LR Frame Kit accessories diagram
Figure 3.1: Diagram showing all included accessories and parts.

4. Specifications

Feature Specification
Product NameRekon10 PRO LR Frame kit
ModelRekon10 PRO LR Frame kit
Material3K Carbon fiber
Type10 inch
Wheelbase455mm
Size476 * 298mm
Top Plate Thickness3mm
Bottom Plate Thickness3mm
Middle Plate Thickness2mm
Front Arm Thickness8mm
Rear Arm Thickness8mm
Frame Protection Bar Thickness2mm
Camera Side Plate Thickness2mm
Top and Middle Plate Space20mm
Flight Controller Mounting Hole30.5x30.5mm
Camera Mount20*20mm
Motor Mounting Hole19*19mm
Weight396.7g
  • Flight Controller: Zeus F722
  • Motor: 31xx/32xx series
  • ESC: 60A
  • Camera: 20x20mm compatible
  • Propeller: 10 inches
  • Battery: 6S 2000-5100mAh

5. Assembly and Setup

Follow these steps carefully to assemble your Rekon10 PRO V2 frame kit. Refer to the diagrams for visual guidance.

FPV frame Assembly Guide for Rekon10 PRO, exploded diagram with parts list
Figure 5.1: Exploded view assembly guide for Rekon10 PRO frame.
  1. Align Arms and Bottom Plate:

    Align the front and back arms with the bottom plate. Ensure correct orientation as shown in the diagram.

    Assembly step 1: Align front and back arms with bottom plate
    Figure 5.2: Step 1 - Aligning arms.
  2. Secure Middle Plate and Arms:

    Use M4*16mm screws to fix the middle plate, bottom plate, front arms, and back arms together. Ensure all components are flush before tightening.

    Assembly step 2: Use M4*16mm screws to fix the middle plate and the bottom plate, the front arm and back arm
    Figure 5.3: Step 2 - Securing middle plate and arms.
  3. Attach Protection Plate and Aluminum Posts:

    Fix the protection plate and M3*30mm aluminum posts using M3*8mm screws.

    Assembly step 3: Use M3*8mm screws to fix the protection plate and M3*30mm aluminum post
    Figure 5.4: Step 3 - Attaching protection plate and posts.
  4. Install Camera Side Plate:

    Carefully install the camera side plates into their designated slots.

    Assembly step 4: Install the camera side plate
    Figure 5.5: Step 4 - Installing camera side plate.
  5. Finalize Main Body Assembly:

    Use M3*20mm screws to secure the bottom plate, middle plate, front arm, and back arm. Integrate M3*18mm and M3*30mm aluminum posts as required for structural integrity.

    Assembly step 5: Use M3*20mm screws to fix the bottom plate, middle plate and front arm, back arm, use M3*18mm aluminum integral, M3*30mm screws
    Figure 5.6: Step 5 - Finalizing main body.
  6. Mount Electronic Components (TPU Parts):

    Install the buzzer mount, DJI Air unit Block B, DJI Air unit Block A, and GPS mount. Fix the T-type antenna mount using M2*16mm or M2*20mm screws as appropriate.

    Assembly step 6: Install the buzzer mount, Air unit mount B, Air unit mount A and GPS mount, fix the T-type antenna mount with M2*16mm or M2*20mm
    Figure 5.7: Step 6 - Mounting electronics.
  7. Attach Top Plate and GoPro Mount:

    Use M3*8mm screws to fix the frame top plate and the GoPro mount. Carefully route the antenna into the GPS mount.

    Assembly step 7: Use M3*8mm screws to fix the frame top plate and gopro mount, put the antenna into gps mount
    Figure 5.8: Step 7 - Attaching top plate and GoPro mount.
  8. DJI O3 Camera VTX Compatibility:

    The frame is designed to be compatible with the DJI O3 camera VTX system.

    Assembly step 8: Compatible with DJI O3 camera VTX
    Figure 5.9: Step 8 - DJI O3 compatibility.
  9. Arm Protection Bar:

    The design includes an arm protection bar to improve overall stability and durability.

    Assembly step 9: Increase the design of arm protection bar, improve stability
    Figure 5.10: Step 9 - Arm protection bar.

6. Operating Instructions

As a frame kit, the Rekon10 PRO V2 does not have operational functions on its own. Once assembled with all necessary electronic components (flight controller, ESC, motors, FPV system, receiver, battery), refer to the individual manuals for those components for detailed operating procedures. This frame provides a stable and durable platform for:

  • Long-range FPV flights.
  • High-altitude exploration.
  • Carrying payloads such as GoPro cameras for cinematic footage (GoPro mount included).
Rekon10 PRO LR Frame Kit with GoPro mounted
Figure 6.1: Rekon10 PRO LR Frame Kit with a GoPro camera mounted.

7. Maintenance

Regular maintenance will ensure the longevity and performance of your Rekon10 PRO V2 frame kit.

  • Inspect Regularly: Before and after each flight, inspect the carbon fiber plates and arms for any cracks, delamination, or signs of stress.
  • Check Screws: Ensure all screws and nuts are tight. Vibrations during flight can loosen hardware. Apply a small amount of thread-locker (e.g., blue Loctite) to metal-to-metal screws if necessary, but avoid on plastic or carbon fiber.
  • Clean Components: Keep the frame free from dirt, dust, and debris. Use a soft brush or compressed air. Avoid harsh chemicals that could damage carbon fiber or TPU parts.
  • TPU Parts: Check TPU mounts (GoPro, GPS, antenna, buzzer) for wear or damage. Replace if they become brittle or lose their grip.
  • Arm Protection Bars: Periodically check the arm protection bars for any deformation or damage, as they are crucial for stability.

8. Troubleshooting

This section addresses common issues related to the frame kit itself. For issues related to electronic components, refer to their respective manuals.

Problem Possible Cause Solution
Frame feels wobbly or unstable after assembly. Loose screws or improperly seated components. Re-check all screws and ensure they are tightened securely. Verify that all carbon fiber plates and aluminum posts are correctly aligned and seated.
Cracks or damage on carbon fiber parts. Impact during use or overtightening of screws. Replace damaged carbon fiber parts immediately. Avoid overtightening screws during assembly.
TPU mounts are loose or components fall out. Worn out or damaged TPU parts. Replace the affected TPU mount. Ensure components are properly inserted into the mounts.

9. User Tips

No specific user tips were available from reviews or Q&A for this product at the time of manual creation. However, general tips for FPV frame kits include:

  • Cable Management: Plan your wiring carefully to keep cables tidy and away from propellers or moving parts. Use zip ties or electrical tape.
  • Weight Distribution: Pay attention to the balance of your components, especially batteries, to ensure optimal flight performance.
  • Pre-Flight Checks: Always perform a thorough pre-flight check, including inspecting the frame for any loose parts or damage.

10. Support

For technical support, warranty claims, or inquiries regarding missing/damaged parts, please contact the seller or manufacturer directly through the platform where the product was purchased. Provide your order number and a detailed description of the issue for prompt assistance.

© 2023 HGLRC. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.