Speedybee F405 V4 Stack BLS 55A

Contents

Speedybee F405 V4 Stack BLS 55A 4-in-1 ESC&FC User Manual

Model: F405 V4 Stack BLS 55A

1. Introduction

The Speedybee F405 V4 Stack BLS 55A is a high-performance flight controller (FC) and 4-in-1 electronic speed controller (ESC) stack designed for FPV drones, including X8, Y6, and fixed-wing aircraft. This integrated unit offers advanced features such as wireless configuration via the SpeedyBee app, robust power delivery, enhanced protection, and comprehensive connectivity options for various peripherals.

Speedybee F405 V4 Stack BLS 55A 4-in-1 ESC&FC in retail packaging

The Speedybee F405 V4 Stack, including the Flight Controller and 4-in-1 ESC, is presented in its retail packaging.

2. Package Contents

Please verify that all items listed below are included in your package:

Speedybee F405 V4 Stack BLS 55A 4-in-1 ESC&FC package contents

All components included in the Speedybee F405 V4 Stack package, laid out for inspection.

  1. SpeedyBee F405 V4 Flight Controller x 1
  2. SpeedyBee BLS 55A 4-in-1 ESC x 1
  3. 35V 1000uF Low ESR Capacitor x 1
  4. M3 Nylon Nut x 5
  5. M3 silicone O Ring x 5
  6. M3*8mm Silicone Grommets (for FC) x 1
  7. M3*8.1mm Silicone Grommets (for ESC) x 1
  8. SH 1.0mm 25mm-length 8pin Cable (for FC-ESC connection) x 1
  9. SH 1.0mm 75mm-length 8pin Cable* x 1
    *When the ESC tail faces the drone's front, use this cable for the flight controller and ESC; both ends plug interchangeably.
  10. M3*30mm Inner-hexagon Screws x 5
  11. DJI 6pin Cable (80mm) x 1
  12. XT60 Power Cable (70mm) x 1

3. Setup

3.1 Physical Installation

The Speedybee F405 V4 Stack has a compact design with a total height of 16.1mm when assembled. Adhere to the standard mounting method for installation. The orientation of the gyroscope and motor sequence can be adjusted through software settings.

Side view of Speedybee F405 V4 Stack

Side view of the Speedybee F405 V4 Flight Controller and BLS 55A 4-in-1 ESC stacked, showing the height and connectors.

Important Stack Installation Note:

If you choose an inverted mounting configuration, exercise extreme caution regarding the space between the frame, the Flight Controller (FC), and the Electronic Speed Controller (ESC). It is critical to swap the silicon pads when changing the positions of the FC and the ESC to prevent any contact between the FC's USB interface and the ESC, which could lead to a short circuit. Any damage resulting from improper installation of this nature is not covered under the Warranty.

Speedybee F405 V4 Stack installation note regarding USB interface clearance

Diagram illustrating the need to ensure sufficient clearance between the FC's USB port and the ESC to prevent short circuits.

3.2 Wiring Diagrams

Proper wiring is crucial for the functionality and safety of your drone. Refer to the diagrams below for connecting your Flight Controller and ESC to various peripherals.

3.2.1 FC & ESC Connection

The FC and ESC are connected via an 8-pin cable. Direct soldering is also an option. Always connect the included 1000uF Low ESR capacitor to prevent damage from voltage spikes during power-up.

Speedybee F405 V4 FC and BLS 55A ESC direct soldering pads definition

Diagram showing color-coded wires for direct soldering connections between the F405 V4 Flight Controller and BLS 55A 4-in-1 ESC.

3.2.2 DJI Air Unit Connections

The F405 V4 Stack features dedicated connectors for DJI Air Units.

  • DJI O3 Air Unit: Use the 6-pin cable provided with the O3 Air Unit.
  • Wiring diagram for Speedybee F405 V4 FC to DJI O3 Air Unit

    Wiring diagram for connecting the Speedybee F405 V4 FC to a DJI O3 Air Unit.

  • DJI O3/Vista/Link/Air Unit V1: Use the 6-pin cable (accessory No.11) included in the F405 V4 stack package.
  • Wiring diagram for Speedybee F405 V4 FC to DJI Air Unit V1

    Wiring diagram for connecting the Speedybee F405 V4 FC to a DJI O3/Vista/Link/Air Unit V1.

3.2.3 Receiver Connections (SBUS & ELRS)

Important notice for SBUS receiver:

When using an SBUS receiver, connect its SBUS signal wire to the SBUS pad on the front side of the flight controller (this pad internally uses UART2). If you are also using a DJI Air Unit (O3/Link/Vista/Air Unit V1) simultaneously, you must disconnect the SBUS signal wire from the Air Unit harness. Failure to do so will prevent the SBUS receiver from being properly recognized by the flight controller. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

Important notice regarding SBUS receiver connection with DJI Air Unit

Diagram illustrating the SBUS receiver connection and the critical step of disconnecting the SBUS wire from the DJI Air Unit harness if an external SBUS receiver is used.

Important notice for ELRS receiver:

We recommend connecting the ELRS receiver's TX and RX to the T2 and R2 pads on the flight controller. However, when using the DJI Air Unit simultaneously, some ELRS receivers may not be recognized properly by the flight controller. If you encounter this issue, you need to disconnect the SBUS signal wire from the Air Unit harness. You can use tweezers to pick out the SBUS wire from the 6-pin harness connector (or directly cut this wire) and insulate the exposed part of the wire carefully.

Important notice regarding ELRS receiver connection with DJI Air Unit

Diagram illustrating the ELRS receiver connection and the critical step of disconnecting the SBUS wire from the DJI Air Unit harness if an ELRS receiver is used.

3.2.4 Comprehensive Wiring Diagram

For all other peripheral connections, refer to the comprehensive wiring diagram below:

Comprehensive wiring diagram for Speedybee F405 V4 Flight Controller

A detailed wiring diagram showing connections for various receivers, LEDs, Servo, Buzzer, GPS, DJI Air Unit, and Analog VTX to the F405 V4 Flight Controller.

3.3 Initial Configuration

  • Bluetooth: The F405 V4 FC supports Bluetooth for wireless configuration. Ensure MSP is enabled with a baud rate of 115200 on UART4 in your flight controller firmware settings.
  • SD Card: For Blackbox data logging, use a microSD card (Standard (SDSC) or High Capacity (SDHC) under 32GB). Extended Capacity (SDXC) cards are not supported. The card must be formatted with FAT16 or FAT32 (recommended). The FC can recognize up to 4GB of Blackbox data.
  • Current Sensor: For the SpeedyBee BLS 55A ESC, set the current sensor scale to 400 and Offset to 0 in your Betaflight/iNAV configurator.
  • Firmware: The FC supports BetaFlight (Default) and INAV firmware. The firmware target name is SPEEDYBEEF405V4.
  • ESC Firmware: The ESC runs BLHeli_S J-H-40 firmware. You can use https://esc-configurator.com/ for PC configuration.

4. Operating Instructions

4.1 Wireless Configuration via SpeedyBee App

The Speedybee F405 V4 Stack allows for wireless configuration of both the FC and ESC using the SpeedyBee mobile app. Connect your phone via Bluetooth to tune your quad anytime, anywhere.

Speedybee app for wireless FC and ESC configuration

Screenshots of the Speedybee app interface for motor configuration and PID tuning, demonstrating wireless setup capabilities.

4.2 Motor Direction Settings

You can change motor directions wirelessly through the SpeedyBee app. Navigate to App > Motors > Motor Direction Settings to adjust as needed after your build is complete.

4.3 Battery Level Indicator

The Flight Controller features a convenient 4-level LED battery capacity indicator. Upon connecting the battery, you can instantly check the battery level:

  • 1 LED solid: Battery level 10-25%
  • 1 LED blinking: Battery level < 10%
  • X1: < 25%
  • X2: 25%-50%
  • X3: 50%-75%
  • X4: 75%-100%
Speedybee F405 V4 Flight Controller 4-level battery indicator

Diagram showing the LED indicators and their corresponding battery level ranges.

4.4 LED Pad Switching

The FC provides 4 sets of LED pads for connecting LED strips. You can cycle through different LED presets by tapping the BOOT button. To switch to Betaflight LED mode, long-press the BOOT button.

Speedybee F405 V4 Flight Controller LED pads and switching

Image showing the FC with LED strips connected to the four corners, illustrating the LED pad functionality.

5. Maintenance

  • SD Card Management: Regularly clear your microSD card to ensure sufficient space for Blackbox data logging. Always format your SD card to FAT16 or FAT32 for optimal compatibility with Betaflight/iNAV firmware.
  • General Care: Keep the flight controller and ESC clean and free from dust, dirt, and moisture. Avoid exposing the components to extreme temperatures or physical shock.

6. Troubleshooting

  • SBUS Receiver Not Recognized: If you are using an external SBUS receiver concurrently with a DJI Air Unit (O3/Link/Vista/Air Unit V1) and the receiver is not recognized, ensure you have disconnected the SBUS signal wire from the DJI Air Unit harness.
  • ELRS Receiver Issues: If your ELRS receiver is not functioning correctly when used with a DJI Air Unit, try disconnecting the SBUS signal wire from the Air Unit harness.
  • Power-up Damage: To prevent damage from voltage spikes during power-up, always ensure the included 1000uF Low ESR capacitor is properly connected to the ESC.
  • FC Bricked/Firmware Flashing: If your Flight Controller becomes unresponsive (bricked), you can force it into DFU mode for firmware flashing by pressing and holding the BOOT button while powering on the FC.
  • Short Circuit during Installation: If you experience a short circuit after installation, particularly with inverted mounting, re-check the clearance between the FC's USB interface and the ESC. Ensure silicon pads are correctly swapped to prevent contact.
  • SD Card Not Working: Verify that your microSD card is Standard (SDSC) or High Capacity (SDHC) under 32GB and formatted to FAT16 or FAT32. SDXC cards are not supported.

7. Specifications

Speedybee F405 V4 30x30 Flight Controller and BLS 55A 4-in-1 ESC specifications

Detailed table listing specifications for both the Speedybee F405 V4 30x30 Flight Controller and the Speedybee BLS 55A 30x30 4-in-1 ESC.

7.1 SpeedyBee F405 V4 30x30 Flight Controller

Feature Specification
MCUSTM32F405
IMU (Gyro)ICM42688P
USB Port TypeType-C
BarometerBuilt-in
OSD ChipAT7456E
BLE BluetoothSupported (MSP enabled with baud rate 115200 on UART4)
WIFINot supported
DJI Air Unit Connection6-pin connector or direct soldering
Split DJI Air Unit PlugCompatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1
Blackbox MicroSD Card SlotSupports SDSC/SDHC under 32GB (FAT16/FAT32 format), max 4GB recognized
Current Sensor InputSupported (Scale=400, Offset=0 for BLS 55A ESC)
Power Input3-6S LiPo
5V Output9 groups, total 3A current load
9V Output2 groups, total 3A current load
3.3V OutputSupported (up to 500mA)
4.5V OutputSupported (up to 1A)
ESC SignalM1-M4 (bottom), M5-M8 (front)
UART8 sets (UART1-UART6, UART4 for Bluetooth)
ESC TelemetryUART6 (R6/UART6)
I2CSupported (SDA & SCL pads on front)
Traditional Betaflight LED PadSupported (5V, G, LED pads on bottom)
BuzzerBZ+ and BZ- pad for 5V buzzer
BOOT ButtonDFU mode, LED presets, Betaflight LED mode switching
RSSI InputSupported (R5 on front)
Smart Port / F.PortNot supported
Supported FC FirmwareBetaFlight (Default), INAV
Firmware Target NameSPEEDYBEEF405V4
Mounting30.5x30.5mm, 4mm hole diameter
Dimension41.6(L) x 39.4(W) x 7.8(H)mm
Weight8.9g

7.2 SpeedyBee BLS 55A 30x30 4-in-1 ESC

Feature Specification
Product NameSpeedyBee BLS 55A 30x30 4-in-1 ESC
FirmwareBLHeli_S J-H-40
PC Configurator Download Linkhttps://esc-configurator.com/
Continuous Current55A * 4
Burst Current70A (10 Seconds)
TVS Protective DiodeYes
External Capacitor1000uF Low ESR Capacitor (in the package)
ESC ProtocolDSHOT300/600
Power Input3-6S LiPo
Power OutputVBAT
Current SensorSupported (Scale=400 Offset=0)
ESC TelemetryNot supported
Mounting30.5x30.5mm, 4mm hole diameter
Dimension45.6(L) * 44(W) * 8(H)mm
Weight22.5g

8. User Tips

  • Inspect Package Contents: Upon receiving your Speedybee F405 V4 Stack, carefully check all package contents against the provided list to ensure completeness and absence of damage.
  • Verify Authenticity: To ensure you have a genuine Speedybee product, purchase from authorized dealers and look for official branding.

9. Warranty and Support

Speedybee products are designed for high performance and reliability. Please note that damage resulting from improper installation, modification, or misuse of the product may void the warranty. For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the official Speedybee support channels.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.