ASAIR ACD1200

Contents

ASAIR ACD1200 CO2 Infrared Sensor Module User Manual

High Precision CO2 Concentration Detection based on NDIR Principle

1. Introduction

The ASAIR ACD1200 is a high-precision infrared carbon dioxide (CO2) sensor module designed for accurate and reliable CO2 concentration detection. Utilizing the Non-Dispersive Infrared (NDIR) principle, this module offers excellent long-term stability, rapid response, and strong anti-interference capabilities, making it suitable for a wide range of applications including HVAC systems, air purifiers, smart homes, and agricultural greenhouses.

ASAIR ACD1200 Infrared Carbon Dioxide Sensor with key specifications
Figure 1: ASAIR ACD1200 Infrared Carbon Dioxide Sensor Module with highlighted specifications.

2. Features

  • NDIR Principle: Employs Non-Dispersive Infrared technology for precise CO2 measurement.
  • High Precision: Accuracy of ±(50ppm+5% reading).
  • Wide Measuring Range: Detects CO2 concentrations from 400 to 5000 ppm.
  • Rapid Response: Offers quick detection and fast recovery time.
  • Strong Anti-interference: Designed to resist external interference for stable readings.
  • No Oxygen Dependence: Measurements are not affected by oxygen levels.
  • Excellent Long-Term Stability: Ensures consistent performance over extended periods.
  • Good Selectivity: Specifically sensitive to CO2.
  • Standard Digital Output: Provides I²C and UART communication interfaces.
  • Low Power Consumption: Typical power consumption of 100mW.

3. Specifications

ParameterValue
Product ModelACD1200
Working Voltage3.3-5.5V
Working Current<45mA
Measuring Range400-5000ppm
Accuracy±(50ppm+5% reading)
OutputI²C/UART
Operating Conditions0-50°C, 0-95%RH (non-condensing)
Preheating Time3min
Data Update Frequency2s
Life Expectancy>10 years
Comprehensive product information including features, application scenarios, product parameters, structural dimensions, working principle, and interface definitions.
Figure 2: Detailed product overview, specifications, and diagrams (refer to the image for specific structural dimensions and working principle diagram).

4. Setup and Installation

The ACD1200 module is designed for easy integration into various systems. Proper connection of the pins is crucial for correct operation.

4.1 Pin Definitions

The module features 5 pins for power and communication:

Pin No.LabelDescription
1VCCPower supply positive (3.3-5.5V)
2GNDGrounding
3SCL/RXI²C clock line or UART receive data line
4SDA/TXI²C data line or UART transmit data line
5SETSetting the communication method (e.g., I²C or UART selection)
Bottom view of the ACD1200 PCB showing pin labels for wiring.
Figure 3: Bottom view of the ACD1200 module with pin labels.

4.2 Physical Dimensions

The structural dimension drawing provides detailed measurements for integrating the module into your design.

Structural dimension drawing of the ACD1200 sensor module with measurements in millimeters.
Figure 4: Structural dimension drawing of the ACD1200 module (refer to the image for specific measurements).

4.3 Working Principle Overview

The NDIR working principle involves an infrared light source, an air chamber, a filter, and an infrared sensor. CO2 molecules absorb specific wavelengths of infrared light, and the sensor measures the remaining light intensity to determine the CO2 concentration.

Working principle diagram of the NDIR CO2 sensor, showing light source, air chamber, filter, and infrared sensor.
Figure 5: Simplified working principle diagram of the NDIR CO2 sensor.

5. Operating Instructions

  1. Power On: Connect the VCC and GND pins to a stable power supply within the 3.3-5.5V range.
  2. Preheating: Allow the module to preheat for approximately 3 minutes after power-on. During this time, the sensor stabilizes, and readings may not be accurate.
  3. Communication Setup: Configure the communication method (I²C or UART) using the SET pin as per your system requirements. Refer to the detailed communication protocol documentation (typically available from the manufacturer) for specific commands and data formats.
  4. Data Acquisition: Once preheated, the module will provide CO2 concentration data at a frequency of 2 seconds via the selected communication interface.
  5. Environmental Conditions: Ensure the operating environment adheres to the specified conditions (0-50°C, 0-95%RH non-condensing) for optimal performance and longevity.

6. Maintenance

  • Keep Clean: Ensure the sensor's optical path (inlet and outlet) is free from dust, dirt, and obstructions. Use a soft, dry cloth for cleaning if necessary.
  • Avoid Condensation: Operate the sensor within the specified humidity range (0-95%RH non-condensing) to prevent damage from moisture.
  • Stable Power Supply: Provide a stable and clean power supply to the module to ensure accurate readings and prevent electrical damage.
  • Avoid Harsh Environments: Do not expose the sensor to corrosive gases, extreme temperatures, or high-vibration environments.
  • Calibration: While the sensor offers excellent long-term stability, periodic calibration may be required for applications demanding the highest accuracy over very long periods. Refer to the manufacturer's specific calibration procedures if available.

7. Troubleshooting

  • No Readings/Incorrect Readings:
    • Check power supply connections (VCC, GND) and ensure voltage is within 3.3-5.5V.
    • Verify communication wiring (SCL/RX, SDA/TX) and ensure the correct communication protocol (I²C/UART) is selected via the SET pin.
    • Allow sufficient preheating time (3 minutes) after power-on.
    • Ensure the sensor's optical path is not blocked or dirty.
    • Confirm your microcontroller's code is correctly implementing the communication protocol and parsing the sensor data.
  • Fluctuating Readings:
    • Ensure the sensor is in a stable environment, away from strong air currents or rapid temperature changes.
    • Check for electromagnetic interference (EMI) from nearby electronic components.
    • Verify the power supply is stable and free from noise.
  • Sensor Not Responding:
    • Power cycle the module.
    • Recheck all wiring connections.
    • If using I²C, ensure the address is correct and no other devices are conflicting.
    • If using UART, verify baud rates and serial settings.

8. User Tips

  • For initial testing, consider using a development board (e.g., Arduino, ESP32) with readily available I²C or UART libraries to quickly get readings.
  • When integrating into a sealed enclosure, ensure there is adequate airflow to the sensor's inlet/outlet for accurate ambient CO2 measurement.
  • Always refer to the official ASAIR documentation for the most up-to-date communication protocols and advanced features.

9. Warranty and Support

For warranty information, technical support, or further inquiries regarding the ASAIR ACD1200 CO2 Infrared Sensor Module, please contact the manufacturer or your point of purchase. Ensure to provide your product model (ACD1200) and any relevant serial numbers when seeking support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.