DIATONE MAMBA F45/F55/F65_128K

Contents

DIATONE MAMBA F45/F55/F65_128K BLHeli_32 4in1 ESC Instruction Manual

Model: MAMBA F45/F55/F65_128K | Brand: DIATONE

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the DIATONE MAMBA F45, F55, and F65_128K BLHeli_32 4in1 Electronic Speed Controllers (ESCs). These ESCs are designed for RC FPV Racing Drones, offering high performance and reliability. Please read this manual thoroughly before use to ensure proper setup and safe operation.

2. Specifications

The MAMBA 4in1 ESC series comes in three variants (F45, F55, F65), each with specific current ratings. All models feature BLHeli_32 firmware and support Dshot protocols.

FeatureMAMBA F45_128K ESCMAMBA F55_128K ESCMAMBA F65_128K ESC
Working Voltage4 ~ 6S Lipo (16.8V ~ 25.2V)4 ~ 6S Lipo (16.8V ~ 25.2V)4 ~ 6S Lipo (16.8V ~ 25.2V)
Output Current45A × 455A × 465A × 4
Peak Current (10S)55A65A75A
BEC OutputNONONO
FirmwareBLHELI_32BLHELI_32BLHELI_32
TargetMAMBA F45_128KMAMBA F55_128KMAMBA F65_128K
ProtocolDSHOT300/600/1200DSHOT300/600/1200DSHOT300/600/1200
PWM24 ~ 128K24 ~ 128K24 ~ 128K
TVS Power ProtectionYesYesYes
Installation Size30.5mm/M330.5mm/M330.5mm/M3
Size44.5x40x7.0mm44.5x40x7.0mm44.5x40x7.0mm
Weight15g15g15g
CURR (Current Sensor)YesYesYes
TelemetryYesYesYes

3. Package Contents

Please verify that all items are present in your package:

  • DIATONE MAMBA 4in1 ESC (F45, F55, or F65_128K model, depending on your purchase)
  • High-frequency filter capacitance 1000uF/35V × 1
  • 8Pin SH1.0 Flight Controller to ESC Connection Cable × 2
  • AMASS XT60 Power Plug × 1

4. Setup and Installation

Careful installation is crucial for the performance and longevity of your ESC. The MAMBA ESCs feature 'SUPER BIG SOLDERING PADs' for easier and more secure connections.

4.1 Wiring Diagram - MAMBA F45_128K ESC

MAMBA F45_128K ESC Wiring Diagram and Specifications
Figure 1: Wiring Diagram for MAMBA F45_128K ESC. Shows motor connections (MOTOR 1-4), GND, VCC, S1-S4 (signal), TX (telemetry), and CURR (current sensor) pads. Also indicates capacitor connection.

4.2 Wiring Diagram - MAMBA F55_128K ESC

MAMBA F55_128K ESC Wiring Diagram and Specifications
Figure 2: Wiring Diagram for MAMBA F55_128K ESC. Displays motor connections (MOTOR 1-4), GND, VCC, S1-S4 (signal), TX (telemetry), and CURR (current sensor) pads. Includes capacitor connection details.

4.3 Wiring Diagram - MAMBA F65_128K ESC

MAMBA F65_128K ESC Wiring Diagram and Specifications
Figure 3: Wiring Diagram for MAMBA F65_128K ESC. Illustrates motor connections (MOTOR 1-4), GND, VCC, S1-S4 (signal), TX (telemetry), and CURR (current sensor) pads. Also shows capacitor connection.

4.4 General Wiring Guidelines

  • Power Input: Connect your 4-6S Lipo battery via the AMASS XT60 power plug to the main positive (+) and negative (-) pads on the ESC.
  • Motor Connections: Solder your motors to the MOTOR 1, MOTOR 2, MOTOR 3, and MOTOR 4 pads as indicated in the diagrams. Ensure correct motor rotation direction is configured in your flight controller or BLHeliSuite.
  • Flight Controller Connection: Use the provided 8Pin SH1.0 cable to connect the ESC to your flight controller. Ensure that GND, VCC, and signal lines (S1-S4) are correctly aligned.
  • Telemetry (TX): Connect the TX pad to the appropriate UART RX pad on your flight controller for ESC telemetry data.
  • Current Sensor (CURR): Connect the CURR pad to the current sensor input on your flight controller for accurate current monitoring.
  • Capacitor Installation: A 1000uF/35V high-frequency filter capacitor is requested when using a 6S battery. Solder it to the main battery pads (+ and -) as close to the ESC as possible to reduce voltage spikes and electrical noise.

5. Operation

The MAMBA 4in1 ESCs utilize BLHeli_32 firmware, known for its advanced features and performance. They support Dshot 300, Dshot 600, and Dshot 1200 digital protocols for precise motor control.

  • Firmware Configuration: Connect the ESC to your computer via your flight controller (using passthrough) and use the BLHeliSuite32 software to configure ESC settings, update firmware, and reverse motor direction if needed.
  • Dshot Protocol: Ensure your flight controller is configured to use the Dshot protocol (300, 600, or 1200) that matches your preference and setup. Dshot 1200 offers the fastest communication.
  • Telemetry: If connected, ESC telemetry data (RPM, temperature, current, voltage) can be displayed on your OSD (On-Screen Display) or logged by your flight controller.

6. Maintenance

  • Regular Inspection: Periodically check all solder joints for cold joints or cracks. Inspect the ESC for any signs of physical damage, burnt components, or debris.
  • Cleaning: Keep the ESC clean from dust, dirt, and moisture. Use compressed air or a soft brush to remove debris. Avoid using liquid cleaners directly on the board.
  • Heat Management: Ensure adequate airflow around the ESC during operation to prevent overheating. Avoid covering the ESC with excessive tape or components that restrict cooling.
  • Firmware Updates: Check the official DIATONE or BLHeli_32 website for the latest firmware updates. Keeping your ESC firmware up-to-date can improve performance and fix bugs.

7. Troubleshooting

  • Motor Not Spinning: Check motor connections, ensure proper soldering, and verify motor direction and protocol settings in BLHeliSuite32 and your flight controller.
  • Intermittent Motor Operation: Could indicate a loose solder joint, damaged motor, or interference. Re-solder connections and check for physical damage.
  • ESC Overheating: Ensure proper cooling, check for short circuits, or motors drawing excessive current. Reduce prop size or adjust PID settings if necessary.
  • No Power to Flight Controller: Verify main battery connection and check for continuity on VCC and GND lines from the ESC to the flight controller. Remember, these ESCs do NOT have a BEC output, so your flight controller must be powered separately or from another BEC.
  • Telemetry Not Working: Confirm TX pad is connected to the correct UART RX on the flight controller and that telemetry is enabled in BLHeliSuite32 and your flight controller firmware.

8. User Tips

  • Solder Quality: Always ensure clean, strong solder joints. Poor soldering is a common cause of issues in FPV electronics. The large soldering pads on MAMBA ESCs are designed to assist with this.
  • Capacitor for 6S: Do not skip installing the recommended capacitor when using 6S batteries. It significantly helps in filtering voltage spikes and protecting your electronics.
  • Test Before Flight: After any installation or modification, always perform a bench test (without propellers) to ensure all motors spin correctly and respond to throttle inputs as expected.

9. Warranty and Support

For warranty claims or technical support, please contact your retailer or the manufacturer directly. Keep your proof of purchase for any warranty-related inquiries. Always refer to the official DIATONE website for the most up-to-date information and resources.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.