1. Safety Instructions
Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire or serious personal injury.
Warning:
When using electrical appliances, basic precautions should always be taken and observed.
1.1. Electrical Safety
- To reduce the risk of electrical shock, do not put inflator in water or other liquid. Do not place or store appliance where it can fall or be pulled into a tub or sink.
- Use this product only with batteries and chargers.
1.2. Personal Safety
- When operating the inflator, keep alert, observe what you are doing, and use common sense. Do not use the inflator when you are tired or under the influence of drugs, alcohol or medication. Inattention when operating the inflator may cause serious personal injury.
- When operating the inflator, always maintain a proper foothold and balance. The correct foothold and balance can better control the inflator in unexpected situations.
- Goggles shall be worn during use, and dust-proof masks, anti-skid safety shoes, hard hats or hearing protection devices must be used if necessary.
- Do not wear loose clothes and keep long hair. Loose clothes, jewelry or long hair may be sucked into the air inlet, causing wind blockage and even damaging the machine.
- Do not use on ladders or unstable supports. A stable foothold on a solid ground can better control the inflator in case of accidents.
- Do not disassemble the inflator. Do not operate the inflator near flammable liquid or in gas or explosive environment. Internal sparks may ignite smoke.
- Do not store the inflator in a humid or high-temperature environment. Do not store at a temperature below 10°C or above 35°C.
- Do not point any inflator at yourself or others.
- Protect the lungs. If there is dust during operation, please wear a mask or dust mask.
- Do not use this inflator to spray chemicals. Toxic fumes or chemicals may damage the parts of the inflator.
- Burst risk: carefully monitor the object during inflation to reduce the risk of over inflation. During inflation, use reliable pressure gauge regularly. The pressure gauge on the inflator is only for reference, so it has no binding force on the accurate value.
- Keep these instructions: always refer to them and use them to guide others who may use this inflator. If you lend this inflator to others, also lend them these instructions.
1.3. Use and Maintenance of Inflator
- Before each use, check whether the hose is fragile or worn to ensure that all connections are secure. Do not use if defects are found. Purchase new hoses or notify an authorized service center for inspection or repair.
- Slowly release all pressure in the system, dust and debris may be harmful. If the switch cannot be opened or closed, do not use the inflator. The inflator that cannot be controlled by the switch is dangerous and must be repaired.
- Before making any adjustment, replacing accessories or storing the inflator, please put the switch in the off position. Such preventive safety measures can reduce the risk of accidentally starting the inflator.
- Store idle inflators out of reach of children and other untrained personnel. Inflators are dangerous in the hands of untrained users.
- Only qualified maintenance personnel can repair the inflator. Repair or maintenance by unqualified personnel may cause injury risk. Only use the same replacement parts when servicing the inflator.
- Understand your inflator, carefully read the operation manual, understand its application and limitations, and specific potential hazards related to this tool.
- Explosion risk: do not operate the inflator so that the output pressure is greater than the marked maximum pressure of the object to be inflated. Do not use it under a pressure greater than 6.8 PA.
- In order to reduce the risk of electric shock, do not get wet and store indoors.
- Check the device for cracks, pinholes or other defects that may make the inflator unsafe. Do not cut or drill holes in the inflator.
- Ensure that there is no obstacle or hose winding in the hose. Do not block the inflation or deflation outlet during operation, which may cause the inflator to lose balance and damage the machine.
- Use the inflator only for its intended use and do not change or modify the original design or function of the device.
- Be careful that misuse and improper operation of this inflator may cause injury to yourself and others. Do not leave the inflator unattended when the air hose is connected to the inflator.
- Do not continue to use the inflator or hose with air leakage or abnormal function.
- When adjusting, repairing or not using the inflator, be sure to disconnect the air source and power supply.
- Do not attempt to pull or carry the inflator through the hose.
- This product is only for family use, not for industrial production.
- Do not use the inflator as a breathing device, do not spray compressed air onto people or animals, and do not blow dust and dirt to yourself or others.
- Do not exceed the pressure rating of any component in the system.
- Protect material and air lines from damage or puncture. Keep hoses and power cords away from sharp objects, chemical leaks, oil, solvents and wet floors.
2. Specifications
| Feature | Description |
|---|---|
| Model Number | LB126 (also referred to as YD-939) |
| Brand Name | Heimerdinger |
| Type | Cordless Air Pump / Air Compressor |
| Voltage | DC18V (compatible with Makita 18V B series lithium battery) |
| Power | 120W |
| Max Air Pressure | 120psi / 995kPa |
| Average Air Consumption | 10L/min |
| Features | Digital pressure gauge, automatic shut-off at desired pressure, cordless design, LED lighting, soft rubber handle |
| Use | Home DIY, Car/RV/SUV/Light Truck Tires, small inflatables, bicycle tires, balls |
| Certification | CE, FCC, RoHS |
| Dimensions (approx.) | Length: 29cm (11.4 inch), Width: 24cm (9.4 inch), Height: 12cm (4.7 inch) |
| Weight (approx.) | 1.435 kg (3.16 lbs) |
2.1. Included Items (No battery, No charger)
- 1-Ball Nozzle
- 1-Tire Valve Nozzle
- 1-Air Bed Nozzle
- 1-12V Car Plug-in Power base
- Cordless Electric Air Pump LB126
3. Parts List and Schematic Diagram
- Digital display
- Start switch
- Set button
- Light switch
- Tire pressure increase/decrease button
- Rubber cover handle
- Battery (not included in this package)
- LED lighting
- Air hose buckle
- Air hose
- Air chuck
- Nozzle interface storage area
- Air inlet
- Cigarette lighter charging line
4. Setup
4.1. How to Charge the Battery Pack (Battery and Charger Not Included)
If you purchase a compatible Makita 18V battery and charger separately:
- When the battery is properly inserted into the charger and charging, the red light is on.
- When the battery is fully charged, the red light is off, and green light is on. Then you can remove the battery.
- When charging more than one battery pack, allow 15 minutes between charges. After many charge/discharge cycles, your battery may lose its ability to hold a charge. If so, please replace it.
- Dispose of batteries at an appropriate waste disposal facility. Do not throw batteries away in common trash receptacles.
- The battery is not fully charged from factory. Please charge the battery for 3-5 hours before the first use. The battery is completely exhausted. The normal charging time is 3-5 hours. Please unplug the charging wire in time after full charging.
- When the performance of the tool begins to decline, replace the new battery; Extreme heat is the most destructive to the battery; Heat generated The more the amount, the faster the battery loses power, and the overheating of the battery will shorten the service life.
- When using the tool, even after the tool has good performance, do not discharge excessively, and the battery power is reduced. When the performance of the tool begins to decline, please stop the tool and charge the battery for the best performance.
4.2. How to Install the Battery (Battery Not Included)
To install a compatible 18V battery:
- Slide the battery pack into the bottom until you hear a click. Make sure that the latch is in place and the battery is secure before operation.
To remove the battery:
- Pull out the battery pack while pressing the battery release latch.
4.3. Installing or Removing 12V Car Power Adapter
- Unravel the cord before using. If a battery is installed, remove it from the machine first by pressing the battery release button and pulling it out.
- Plug the 12V car power adapter into the machine.
- Connect the adapter into the car socket. When ready to use, power the car on.
4.4. Connecting the Air Chuck to the Valve Stem
- Push the air chuck clamp up so that it is in the unlock position.
- Then place the air chuck on the valve stem and make sure the threaded section of the valve stem is inside the air chuck.
- Press the air chuck clamp down until it stops or is parallel with the air hose.
Note:
Improperly connected hoses or accessories may separate under pressure and cause serious injury. Possible air leaks can cause incorrect pressure readings. Ensure that all connections are secure.
4.5. Setting Pressure Value
- Press the power button (on / unit) to read the current tire pressure on the gauge.
- Press the "R" button again to select the tire pressure measurement unit from PSI, KPA, BAR, KG/CM.
- Press the "+" or "-" button to adjust the preset tire pressure. Long press the "+" or "-" button to quickly adjust the working pressure. Short press the "+" or "-" button to adjust the preset working pressure. (Note: increment by 0.05BAR & KG/CM, 1 PSI, 5KPA).
- The preset pressure value will be set after three seconds.
5. Operating Instructions
5.1. Inflation Process
- After connecting the air chuck and setting the desired pressure, press the start switch to inflate.
- When it reaches the preset pressure value, the inflator will stop working automatically.
- Press the power button (on / unit), then press the light button, the LED light is turned on. Press the light button again, the LED light will be flashing.
Note:
The tolerance of the inflator is +/- 2 psi. If it is used continuously for every 10 minutes, a cooling time of 3 minutes is required.
The digital gauge records the preset measurement unit and the value of the last operation. After the air pump reaches the preset pressure value, the digital gauge will automatically shut down after 60 seconds. The maximum pressure is 150 psi.
5.2. How to Install a Sports Ball Needle
For inflating sport balls like basketball, football, etc.:
- Attach the sports ball needle to the air chuck.
- Insert the needle into the ball's valve.
Note:
Do not completely insert the ball needle into the air chuck to prevent the exhaust needle hole from being completely blocked.
When inflating items of 10 psi or less, after each burst of short-term continuous inflation, check by feeling or using a calibrated measuring device to determine the accurate pressure.
6. Maintenance
6.1. Product Maintenance
- Do not let brake fluid, gasoline, petroleum products, penetrating oil, etc. contact with plastic parts. Chemicals may damage, weaken or break plastic, resulting in serious machine injury.
- Wipe the surface of the machine with a soft wet cloth to keep the surface of the inflator clean. Do not use solvents on plastic parts.
- When cleaning plastic parts, avoid using solvents. Most plastics are easily damaged by various irritating solvents and can be damaged due to use. Use clean cloth to remove dirt, dust, oil, grease, etc.
- In order to maintain the best performance of the rechargeable battery, please prevent the battery from overheating, including overcharging and storage, and do not use the machine for a long time. The battery should be charged for 7 hours every three months (if applicable).
6.2. Storage of Air Hoses and Accessories
- When the inflator is not used, put the hose into the storage area on both sides of the tool.
- The adaptors and needles provided with the inflator can also be placed in the storage area.
7. Troubleshooting
7.1. Replacing the Cigar Lighter Fuse
If the cigar lighter cannot provide power for the inflator, check the fuse and see if it is broken.
- Unscrew the head of the cigar lighter.
- Take out the broken fuse.
- Replace with a new fuse.
- Screw the head back on.
8. User Tips
- The digital display shows the voltage, charge level, and remembers the set inflation pressure, which is very convenient for repeated use.
- Ensure you have a compatible Makita 18V B series lithium battery and charger, as these are not included with the air pump.
- Always double-check tire pressure with a reliable external gauge for critical applications, as the inflator's gauge is for reference.
9. Warranty and Support
For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.
An official user manual in PDF format is available for download: View User Manual (PDF)