1. Introduction
Thank you for choosing the HIROYASU CB-1011 Mobile Transceiver. This compact and versatile 11-meter CB radio operates on 27MHz and supports both FM and AM modes with selectable 8W/4W power output. Designed for ease of use and reliable communication, it is compatible with various European and international CB bands. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and longevity of your device.
2. Package Contents
Please check the box for the following items:
- 1 × HIROYASU CB-1011 CB Radio body with Microphone speaker and DC 12V Input cigarette Power Cable
- 1 × Mounting Bracket
- 1 × Microphone Hanger
- 2 × Adjusting Screws
- 4 × Screws for bracket
- 2 × Pads for bracket
- 2 × Screws
- 1 × Spare Fuse
- 1 × User Manual

3. Key Features
- Frequency Range: 26.565-27.99125MHz
- Supports 8 countries CB Bands: DE/EU/CE/PL/UK/IT/IN/US
- AM/FM Two Modes selection
- 40 channels for EU/CE/PL/UK/IT/IN/US, 80 channels for DE
- PH (8W) / PL (4W) HIGH/LOW power select
- Manual / Automatic Squelch level control (ASQ/SQ)
- RF Gain Control (RFG)
- CH9/CH19 Emergency Channel (EMG)
- Channel Scan function
- Keypad Lock for preventing accidental changes
- Powered by 12V Car Cigarette Lighter
- Factory Default Reset option
- Palm-sized and lightweight design for portability
4. Controls and Display

- SQ (Squelch) Button: Controls squelch level and switches between Manual Squelch (SQ) and Automatic Squelch (ASQ).
- RFG (RF Gain) Button: Activates RF Gain control.
- A/F (AM/FM) Button: Selects AM or FM modulation mode and initiates Channel Scan (long press).
- EMG (Emergency) Button: Accesses CH9/CH19 emergency channels and activates Keypad Lock (long press).
- Rotary Knob: Controls Power ON/OFF and Volume. Also used for adjusting squelch level, RF gain, and CB band selection.
- LCD Display: Shows current channel, mode, squelch level, RF gain, and other operational indicators.
- External Speaker Jack: For connecting an external speaker.
- Antenna Jack: UHF, SO239 connector for antenna.

- UP/DN Buttons: Used for channel selection.
- Mic Keypad Lock Switch: Prevents accidental button presses on the microphone.
5. Setup
5.1. Mounting the Transceiver
Use the provided mounting bracket and screws to securely install the CB-1011 in your vehicle. Ensure the location allows for easy access to controls and clear visibility of the display, without obstructing driving. The microphone hanger can be installed in a convenient location for quick access.
5.2. Power Connection
The CB-1011 operates on 12V DC power. Connect the provided DC 12V cigarette power cable to your vehicle's cigarette lighter socket. Ensure a secure connection.

5.3. Antenna Connection
Connect a compatible CB antenna to the UHF, SO239 antenna jack on the rear of the transceiver. A properly tuned antenna is crucial for optimal performance and to prevent damage to the radio.
6. Operating Instructions
6.1. Power On/Off and Volume Control
Rotate the Rotary Knob (5) clockwise to turn the radio ON. Continue rotating to increase the volume. Rotate counter-clockwise to decrease volume and turn OFF the radio.
6.2. Channel Selection
Use the UP and DN buttons on the microphone to change channels. Pressing UP increases the channel number, and pressing DN decreases it.
6.3. CB Band Selection (for your country)
To select the appropriate CB band for your country:
- Turn the radio OFF.
- Press and hold the A/F (3) and EMG (4) buttons simultaneously.
- While holding these buttons, turn the radio ON using the Rotary Knob (5).
- The display will show the current band (e.g., EU, PL, DE, US).
- Rotate the Rotary Knob (5) to cycle through the available CB bands.
- Once your desired band is displayed, turn the radio OFF and then ON again to save the selection.

6.4. AM/FM Mode Switch
Press the A/F (3) button to switch between AM (Amplitude Modulation) and FM (Frequency Modulation) modes. The selected mode will be indicated on the LCD display.
6.5. Squelch Level Control (SQ/ASQ)
The squelch function eliminates background noise when no signal is present. There are two modes:
- Automatic Squelch (ASQ): Press the SQ (1) button briefly to activate ASQ. The radio automatically adjusts the squelch level.
- Manual Squelch (SQ): Press the SQ (1) button again to switch to manual squelch. Rotate the Rotary Knob (5) to adjust the squelch level. A higher number means a tighter squelch (less background noise, but potentially weaker signals missed).

6.6. RF Gain Control (RFG)
Press the RFG (2) button to activate RF Gain control. Then, rotate the Rotary Knob (5) to adjust the RF gain. RF gain controls the sensitivity of the receiver, allowing you to filter out weak signals or noise in congested areas.
6.7. Emergency Channels (CH9/CH19)
Press the EMG (4) button to quickly switch to emergency channels CH9 or CH19. Press it again to toggle between them or return to the last active channel.
6.8. Channel Scan
Long press the A/F (3) button to activate the Channel Scan function. The radio will scan through all available channels until a signal is detected. Press any button to stop scanning.
6.9. Keypad Lock
Long press the EMG (4) button to lock the keypad, preventing accidental changes to settings. Long press again to unlock.
6.10. High/Low Power Select (8W/4W)
To switch between High (8W) and Low (4W) power output:
- Turn the radio OFF.
- Press and hold the EMG (4) and RFG (2) buttons simultaneously.
- While holding these buttons, turn the radio ON using the Rotary Knob (5).
- The display will show 'PH' for High Power (8W) or 'PL' for Low Power (4W).
- Turn the radio OFF and then ON again to save the selection.

6.11. Factory Default Reset
To restore the radio to its factory default settings:
- Turn the radio OFF.
- Press and hold the A/F (3) and RFG (2) buttons simultaneously.
- While holding these buttons, turn the radio ON using the Rotary Knob (5).
- The display will show a reset confirmation.
- Turn the radio OFF and then ON again to complete the reset.
7. Specifications
| Category | Parameter | Value |
|---|---|---|
| General | Modulation Mode | AM/FM |
| Frequency Range | 26.565-27.99125MHz | |
| Frequency Tolerance | ±5.0ppm | |
| Input Voltage | 13.8V±5% | |
| Dimensions | 109*104*25mm | |
| Weight | 421g | |
| Frequency Control | PLL Synthesizer | |
| Operating Temperature Range | -20°c ~ +50°c | |
| Current Drain | Transmit | 2A Max. |
| Receiver (Squelched) | 0.3A | |
| Receiver (Vol Max.) | 0.8A | |
| Antenna | Antenna Connector | UHF, SO239 |
| Transmitter | Power Output | 8 Watts FM/AM |
| Transmission Interference | Inferior to 4nW (-54dBm) | |
| Frequency Response | 300-3000Hz | |
| Modulated Signal Distortion | Inferior to 5% | |
| Output Impedance | 50 ohms | |
| Receiver | Sensitivity | Less than 1uV for 10dB (S+N)/N |
| Image Rejection | 70dB | |
| Adjacent Channel Rejection | 60dB | |
| IF Frequency | 1st 10.695MHz | |
| 2nd 455KHz | ||
| Automatic Gain Control (AGC) | Less than 10dB change in audio output for inputs from 10 to 50000uV | |
| Squelch | Less than 1uV | |
| Audio | Audio Output Power | 1 Watts |
| Frequency Response | 300-3000Hz |
8. Troubleshooting
If you encounter issues with your CB-1011, please refer to the following common problems and solutions:
- No Power: Check the 12V power connection and ensure the cigarette lighter socket is functioning. Verify the fuse in the power cable is not blown. Replace with the spare fuse if necessary.
- No Reception/Transmission: Ensure the antenna is securely connected and properly tuned for the 27MHz band. Check the selected CB band for your region. Adjust the squelch level; if it's set too high, it may block weak signals.
- Poor Audio Quality: Check the microphone connection. Ensure the volume is set appropriately. If using an external speaker, verify its connection and functionality.
- Buttons Unresponsive: Check if the Keypad Lock is activated (long press EMG to unlock).
- Unexpected Behavior: Perform a Factory Default Reset (see section 6.11) to clear any incorrect settings.
If the problem persists after trying these steps, please contact customer support for further assistance.
9. User Tips
- Antenna Selection: For optimal performance, it is crucial to use an antenna specifically designed for the 27MHz CB band. Ensure the antenna is properly tuned (low SWR) to prevent damage to the radio and maximize transmission/reception range.
- Power Output: Use the 8W (High Power) setting for maximum range when needed, but switch to 4W (Low Power) in congested areas or for shorter-range communication to reduce interference and conserve power.
- Squelch Adjustment: Experiment with the Manual Squelch level to find the optimal balance between eliminating background noise and receiving weaker signals. Start with a low setting and gradually increase it until the background hiss disappears.
10. Maintenance
- Cleaning: Use a soft, dry cloth to clean the radio's exterior. Do not use abrasive cleaners or solvents.
- Storage: When not in use for extended periods, store the radio in a dry, cool place away from direct sunlight and extreme temperatures.
- Fuse Replacement: If the radio does not power on, check the fuse in the power cable. Replace it with a fuse of the same type and rating (a spare is included in the package).
11. Warranty and Support
For warranty information, technical support, or service inquiries, please refer to the contact details provided with your purchase documentation or visit the official HIROYASU website. Keep your purchase receipt as proof of purchase.