1. Introduction
This manual provides essential information for the safe and effective operation, maintenance, and care of your DEKO DKID13XL65G Electric Impact Drill. Please read this instruction manual carefully before operating the product and keep it for future reference.
The DEKO DKID13XL65G impact drill is a professional-grade power tool designed for various drilling tasks. It is intended for impact drilling in brick, concrete, and stone, as well as standard drilling in wood, metal, and plastic. Equipped with electronic control and right/left rotation, it is also suitable for screw driving and removing screws.
Figure 1: DEKO DKID13XL65G Electric Impact Drill
2. General Safety Warnings
WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference.
2.1 Work Area Safety
- Keep the work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2.2 Electrical Safety
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators.
- Do not expose power tools to rain or wet conditions.
- Do not abuse the cord. Keep the cord away from heat, oil, sharp edges, or moving parts.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use.
- If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
2.3 Personal Safety
- Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up, or carrying the tool.
- Remove any adjusting key or wrench before turning the power tool on.
- Do not overreach. Keep proper footing and balance at all times.
- Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts.
- If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
- Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
2.4 Power Tool Use and Care
- Do not force the power tool. Use the correct power tool for your application.
- Do not use the power tool if the switch does not turn it on and off.
- Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
- Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool's operation.
- Keep cutting tools sharp and clean.
- Use the power tool, accessories, and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
- Keep handles and grasping surfaces dry, clean, and free from oil and grease.
2.5 Special Safety Instructions for Impact Drills
- Wear ear protectors when impact drilling.
- Use auxiliary handle(s), if supplied with the tool.
- Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord.
- Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance.
- Switch off the power tool immediately when the tool insert jams. Be prepared for high reaction torque that can cause kickback.
- When working with the machine, always hold it firmly with both hands and provide for a secure stance.
- Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.
- Keep your workplace clean.
- Always wait until the machine has come to a complete stop before placing it down.
- Never use the machine with a damaged cable.
- The equipment complies with the safety regulations required for electrical equipment.
- Improper use can lead to personal injury and property damage.
- Keep the instructions for use in safe custody.
- Children should not play with an electrical appliance.
3. Product Overview and Parts Description
Familiarize yourself with the components of your DEKO DKID13XL65G impact drill.
Figure 2: Main components of the impact drill
- Chuck
- Depth gauge
- Mode selector switch
- Auxiliary handle
- Lock-on button
- On/off switch
- Speed Dial
- Clockwise/counter-clockwise rotation switch
- Chuck key
Figure 3: Key features including two modes, speed locking button, and 1/2 inch chuck.
4. Setup
4.1 Auxiliary Handle (4)
WARNING: Before performing any maintenance or adjustment, remove the plug from the socket.
The auxiliary handle (4) provides better stability. Do not use the tool without it.
- The supplied auxiliary handle (4) must first be fitted. Open the clamp by turning the handle anti-clockwise until it is wide enough to slide over the chuck (1) and onto the impact drill.
- Position the auxiliary handle (4) to the most comfortable working position.
- Turn the handle clockwise to secure the auxiliary handle.
- The auxiliary handle (4) is suitable for both left-handed and right-handed users.
Figure 4: Adjusting the auxiliary handle and chuck.
4.2 Fitting and Adjusting the Depth Gauge (2)
The depth gauge (2) is held in place by the auxiliary handle (4) by clamping. The clamp can be released and tightened by turning the handle.
- Release the clamp and fit the depth gauge (2) in the recess provided for it in the auxiliary handle.
- Set the depth gauge to the same level as the drill bit.
- Pull the depth gauge back by the required drilling depth.
- Ensure both the depth gauge (2) and the auxiliary handle (4) are fixed.
- Drill the hole until the depth gauge touches the workpiece.
4.3 Fitting the Drill Bit
NOTE: When selecting a drill bit, use the right type for your job. For best performance, always use sharp drills.
- Open the chuck (1). The drill bit opening must be large enough to fit the drill bit into.
- Select a suitable drill bit. Push the drill bit as far as possible into the chuck opening.
- Close the chuck (1) with the chuck key (9). Check that the drill bit is secure in the chuck (1).
- Check at regular intervals that the drill bit or tool is secure (pull the mains plug).
Figure 5: Securing the drill bit in the chuck.
5. Operating Instructions
WARNING: Failure to unplug the drill could result in accidental starting causing possible serious personal injury.
5.1 Clockwise/Counter-clockwise Rotation Switch (8)
CAUTION: Change switch position only when the drill is at a standstill!
Use the clockwise/counter-clockwise rotation switch (8) to select the desired direction of rotation. Clockwise for forward drilling/screwing, counter-clockwise for reverse (e.g., removing screws).
5.2 On/Off Switch (6) and Lock-on Button (5)
- First, fit a suitable drill bit into the tool.
- Connect the mains plug to a suitable socket.
- Position the drill in the desired drilling position.
To switch on: Press the on/off switch (6).
Continuous operation: Secure the on/off switch (6) with the lock-on button (5).
To switch off: Press the on/off switch (6) briefly.
Figure 6: On/Off switch, lock-on button, and speed dial.
5.3 Adjusting the Speed (6)
Users can infinitely vary the speed by applying greater or lesser pressure to the on/off switch (6).
- Low pressure: Lower speed, suitable for small screws and soft materials.
- Greater pressure: Higher speed, suitable for large/long screws and hard materials.
Tip: Start drilling holes at low speed, then increase the speed in stages. This makes the drill bit easier to control and prevents messy holes.
5.4 Preselecting the Speed (7)
The speed dial (7) allows you to define the maximum speed. The on/off switch (6) can only be pressed to the defined maximum speed setting.
- Set the speed using the speed dial (7) on the on/off switch (6). Turn the wheel towards "+" to increase the speed, and towards "-" to reduce the speed.
- Do not attempt to make this setting whilst the drill is in use.
5.5 Drill / Impact Drill Mode Selector Switch (3)
WARNING: Change switch position only when the drill is at a standstill!
The 2-in-1 switch has two positions for drilling and hammer drilling.
- Drill mode (Drill position): Use for wood, metal, plastic.
- Impact drill mode (Impact drill position): Use for concrete, rock, masonry.
Figure 7: Mode selector switch for drill and impact drill functions.
5.6 Drilling Specific Materials
WARNING: Reverse rotation during impact drilling may damage the drill and drill bit.
Drilling Concrete and Masonry
- Switch the mode selector switch (3) to impact drill position.
- For maximum performance, use high-quality carbide-tipped masonry drill bits.
- Use the drilling setting initially, then revert to the impact action once holes are established.
- Apply light pressure and medium speed for best results in brick.
- Apply additional pressure and high speed for hard materials such as concrete.
- When drilling holes in tile, practice on a scrap piece to determine the best speed and pressure.
Figure 8: Example of drilling into a concrete block.
Drilling Steel
- Switch the drill / impact drill selector switch (3) to drill position.
- Always use HSS drill bits (High Speed Steel) and a low speed setting.
- Lubricate the hole with a suitable cutting fluid to prevent unnecessary drill bit wear.
- Begin drilling at a very low speed to prevent the bit from slipping.
- Always clamp sheet metal. Support thin metal with a block of wood to avoid distorting it.
Inserting/Removing Screws
- Switch the mode selector switch (3) to drill position.
- Use a low speed setting.
Starting Holes
If drilling a deep hole in a hard material, start with a smaller drill bit.
- Use a "wood-pecker" action on deep holes to allow swarf to be ejected.
- If the drill bit snags, switch it off immediately. Try running the drill in reverse to remove the bit.
- Keep the drill in line with the hole. The drill bit should enter at right angles to the work.
- Reduce pressure as the drill is about to break through the item.
- Don't force the drill; let it work at its own pace. Keep the drill bit sharp.
Figure 9: Example of drilling into wood.
Drilling Tiles
- To start the hole, switch the drill / impact drill selector switch (3) to drill position.
- Switch the drill / impact drill selector switch (3) to impact drill position as soon as the drill bit has passed through the tiles.
6. Maintenance
WARNING: Always pull out the mains power plug before starting any cleaning work.
6.1 Cleaning
- Keep all safety devices, air vents, and the motor housing free of dirt and dust. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure.
- Clean the device immediately each time you have finished using it.
- Clean the equipment regularly with a moist cloth and some soft soap. Do not use cleaning agents or solvents; these could attack the plastic parts of the equipment. Ensure that no water can seep into the device.
6.2 Carbon Brushes
In case of excessive sparking, have the carbon brushes checked only by a qualified electrician.
WARNING: The carbon brushes should not be replaced by anyone but a qualified electrician.
6.3 General Maintenance
There are no parts inside the equipment that require additional maintenance by the user.
7. Troubleshooting
This section addresses common issues you might encounter. For more complex problems, refer to the Warranty/Support section.
| Problem | Possible Cause | Solution |
|---|---|---|
| Tool does not switch on/off | Faulty on/off switch (6) | The tool is dangerous and must be repaired by a qualified technician. |
| Tool insert jams or kickback occurs | Overload or drill bit wedged in workpiece | Switch off immediately. Hold the machine firmly with both hands and maintain a secure stance. |
| Drill bit snags during operation | Incorrect drilling technique or material resistance | Switch off immediately. Try running the drill in reverse to remove the bit. Ensure proper alignment and pressure. |
| Excessive sparking from motor | Worn carbon brushes | Have carbon brushes checked and replaced by a qualified electrician. |
| Loss of control during operation | Improper grip, unsecured workpiece, or damaged auxiliary handle | Ensure auxiliary handle is securely fitted. Hold tool firmly with both hands. Secure workpiece with clamping devices. |
8. Specifications
Please refer to the rating label on your tool for specific details.
| Attribute | Specification (DKID13XL65G) | Specification (Other Models) |
|---|---|---|
| Model Number | DKID13XL65G | DKID13XP65, DKID13XP71, DKID13XL71G |
| Supply Voltage | 220-240V~50/60Hz | 220-240V~50/60Hz |
| Rated Power | 650W | 650W (DKID13XP65), 710W (DKID13XP71/DKID13XL71G) |
| No-Load Speed | 0-3000/min | 0-3000/min |
| Impact Rate | 0-48000bpm | 0-48000bpm |
| Chuck Size | 13mm (1/2") | 13mm (1/2") |
| Max Drill Capacity (Concrete) | 13 mm (1/2") | 13 mm (1/2") |
| Max Drill Capacity (Steel) | 13 mm (1/2") | 13 mm (1/2") |
| Max Drill Capacity (Wood) | 25mm (1") | 25mm (1-3/16") |
| Protection Class | II/ | II/ |
| Weight | 1.95KG | 1.95KG |
| Product Size | 28cm*21cm*7cm | 28cm*21cm*7cm |
| Packaging Size | 28.5cm*8cm*26cm | 28.5cm*8cm*26cm |
Figure 10: Product dimensions and maximum drilling capacities.
9. User Tips
Based on common user inquiries and best practices:
- Always ensure the drill bit is sharp and appropriate for the material you are drilling to achieve the best results and prevent damage to the tool or workpiece.
- When drilling into hard materials like concrete, start with a lower speed to create a pilot indentation, then increase speed and engage impact mode for efficient drilling.
- For prolonged use, utilize the lock-on button (5) to maintain continuous operation without constant trigger pressure, reducing user fatigue.
- Regularly check and clean the air vents to prevent overheating and ensure optimal performance of the motor.
10. Warranty and Support
This tool is warranted to the original purchaser to be free from defects in materials and workmanship for a period of 2 years from the original purchase date.
If the tool should fail despite quality controls, it should only be repaired by an authorized electrician or contact your local distributor or service agent.
You can also contact DEKO TOOLS CO., LIMITED by email:
- services@dekotools.com
- support@dekotools.com
The warranty will not apply to the following cases:
- Where this product has been subjected to misuse, abuse, accident, or want of care.
- Where this product has been used for a purpose for which it was not designed or is not suited.
- Where the service of this product has been undertaken by a non-authorized person or company or if non-approved parts have been used.
- Components that are subject to natural wear and tear caused by use in accordance with operating instructions.
For the full user manual, including additional languages (e.g., Spanish), please refer to the official PDF document: DEKO Electric Impact Drill User Manual (PDF).
11. Disposal
The machine and packaging should be sorted for environmentally-friendly recycling. Do not dispose of power tools into household waste! Please recycle them at collection points provided for the purpose. Ask your local authority for information about recycling.
Figure 11: Do not dispose of power tools with household waste.