EARU EASEM-D-TY

Contents

EARU Smart WiFi Multi-Circuit Power Energy Meter User Manual

Model: EASEM-D-TY

1. Welcome

The EARU Smart WiFi Multi-Circuit Power Energy Meter helps you monitor the amount of electricity consumed and produced in your facility by connecting current transformers (CT clamps) to your power cables.

This guide provides an overview of the product and assists you with the initial setup and installation.

Key Features:

  • Tuya compliant, supporting automation with other Tuya devices.
  • Compatible with Single, Split-Phase 120/240VAC, and 3-Phase/4-wire 480Y/277VAC electricity systems.
  • Remotely monitor whole home energy and up to 16 individual circuits with 50A Sub CTs, suitable for solar, lighting, and receptacles.
  • Bi-Directional measurement capabilities.
  • Real-time Voltage, Current, Power Factor, Active Power, and Frequency measurement.
  • Historical data of Energy Consumed and Energy Production.

2. Safety Handling

WARNING: Failure to follow these safety notices could result in fire, electric shock, other injuries, or damage to the Power Meter and other property. Read all the safety notices below before using the Power Meter.

  • Avoid high humidity or extreme temperatures.
  • Avoid long exposure to direct sunlight or strong ultraviolet light.
  • Do not drop or expose the unit to intense vibration.
  • Do not disassemble or try to repair the unit on your own.
  • Do not expose the unit or its accessories to flammable liquids, gases, or other explosives.

3. Product Components

The package includes the main unit, various CT clamps, an external antenna, a power cable, and a mounting bracket.

EARU Smart WiFi Multi-Circuit Power Energy Meter components
Main Unit, Main CTs (3.5mm audio plug), 50A Sub CTs (2.5mm audio plug), External Antenna, Power Cable, Mounting Bracket.

Main Unit Overview:

Main Unit Port Labels
The main unit features 3.5mm audio ports for Main CTs (L1/A, L2/B, L3/C) on the top, 2.5mm audio ports for Sub CTs on the sides, an antenna connector, and a power input port at the bottom.

CT Clamp Specifications:

CT Clamp Dimensions and Direction
Dimensions and weight for 50A, 200A, and 300A CT clamps. Includes instructions for identifying CT direction (P1→P2 or K→L).

The package includes 16 pieces of 50A Caliper (2.5mm audio plug) and 3 pieces of 200A or 300A Caliper (3.5mm audio plug).

4. Technical Specifications

CategorySpecification
Rated Working Voltage90-480VAC 50/60Hz
Calibrated Metering Accuracy±2%
Reading Refreshing SpeedEvery 15 Seconds
Operating Temperature-20℃~+55℃
Operating Humidity≤ 90% non-condensing
Wi-Fi802.11 b/g/n @ 2.4GHz
RF CharacteristicsOperating frequency: 2.4GHz, External magnetic antenna
Supported SystemsSingle-Phase 240VAC line-neutral, Split-Phase 120/240VAC, Three-Phase up to 480Y/277VAC (No Delta/wye/Y/Star Connection)
Dimensions111.3(L) x 81.2(W) x 41.4(H) mm

5. Installation (Setup)

Important Safety Information!

  • The Power Meter must be installed and serviced only by qualified electrical personnel.
  • Do not touch the terminals of the device during testing.
  • Turn off the power before connecting or disconnecting it to an auxiliary device.
  • Double check the power is off with a properly rated voltage sensing device.

Failure to follow these instructions will result in death or serious injury.

5.1. Turn off Power

You need to turn off the main breaker in your electric panel to shut off all power in your home. (However, the service mains are always live!) Then, remove screws securing the cover to the panel to access the circuit breakers.

Electrical Panel with Main Breaker Off
Ensure main breaker is off before proceeding.

5.2. Find a Spot for the Power Meter

Find a suitable location for the Power Meter. You can fit it within your electrical panel or use the mounting bracket to fix it on the wall outside the electrical panel if space is limited.

Mounting Options for Power Meter
Options: On the wall or inside the electrical panel.

5.3. Mounting

The mounting bracket supports rail installation. Click the three hooks on the mounting bracket onto the Din-Rail. Then, locate the hooks of the mounting bracket and line them up with the mounting holes on the Power Meter. Fit the hooks into the mounting holes as shown in the picture. Installation is now completed.

Mounting the Power Meter
Mounting the device onto a Din-Rail using the provided bracket.

5.4. Install the Antenna

Locate the External Antenna outside the electrical panel to ensure that the Power Meter signal is not blocked by metal. The base of the antenna has a magnetic property and can be adsorbed on iron materials. Screw the External Antenna to the Antenna connector on the main unit.

If installing the Power Meter inside the electrical panel, use a screwdriver to punch out a knockout cover and feed the External Antenna cable through the hole.

Antenna Installation Diagram
Connect the external antenna to the main unit and position it outside the metal enclosure.

5.5. Connect the Power Cable

Connect the power cable into the bottom of the main unit until it clicks into place securely.

Power Cable Connection
Diagram showing how to connect the power cable to the main unit and secure N, L1, L2, L3 wires to the neutral bus bar and breaker poles based on system type.

5.6. Clamp Main CTs around Service Mains

Open the clasps on the Main CTs (3.5mm audio plug) to see the arrow (P1→P2 or K→L) or find it on the sticker. This indicates the direction of the CT. Clamp one Main CT on each main service line. Make sure the arrow on the CT must point towards the breakers! Your system may have 1, 2, or 3 main service lines, requiring a corresponding number of Main CTs.

Main CT Clamp Direction
Ensure the CT arrow points towards the breakers.

Insert each 3.5mm audio plug of the Main CT into the corresponding audio jack on the top of the Power Meter (L1/A, L2/B, L3/C).

Main CT Connection to Power Meter
Connect Main CTs to the labeled audio jacks on the Power Meter.

5.7. Clamp Sub CTs around Circuits

If you don't have Sub CTs (2.5mm audio plug), skip this step. Open the clasps on the Sub CTs to see the arrow (P1→P2 or K→L) or find it on the sticker. This is the direction of the CT. Clamp each Sub CT around the circuit you wish to monitor. Make sure the arrow on the CT must point towards the load or Inverter!

Sub CT Clamp Direction
Ensure the Sub CT arrow points towards the load or inverter.

Insert each 2.5mm audio plug of the Sub CT into the audio jack on the side of the Power Meter. Remember the number of the audio jack connected to the circuit you are measuring, as you may need to match it in your app.

Note: If the circuit you are monitoring can generate energy (e.g., from an Inverter), after all wiring is completed, manually set the phase of the circuit in the app settings, otherwise the power measurement will be incorrect.

6. Wiring Reference

Warning: The service mains are always live! Exercise extreme caution.

3-Phase System Wiring

3-Phase Wiring Diagram
Typical wiring for European 3-phase homes and US Commercial systems.

Split-Phase System Wiring (Load Monitoring)

Split-Phase Load Monitoring Wiring Diagram
Typical wiring for US homes with load monitoring.

Split-Phase System Wiring (Solar Monitoring)

Split-Phase Solar Monitoring Wiring Diagram
Typical wiring for US homes with solar monitoring. Main CT must be clamped between the electricity meter and incoming feeds from the inverter.

Single Phase System Wiring

Single Phase Wiring Diagram
Typical wiring for European 1-phase homes.

Video: 3 Phase Electricity Wiring Installation

This video demonstrates the installation process for 3-phase electricity wiring, including turning off power, connecting the main unit and power cable, marking and connecting L1, L2, L3, and N wires, and clamping Main and Sub CTs. It also shows the external antenna connection.

7. Network Configuration (Operating)

The device uses the Smart Life app for network configuration. Note that the device cannot support 5GHz Wi-Fi, only 2.4GHz.

7.1. Download the Smart Life App

Download the application: Smart Life from your App Store or App Market. You can also scan the QR code below to download and install.

Smart Life App QR Code
Scan this QR code to download the Smart Life app.

7.2. Configuration Method 1 (Scan Button)

  1. Open the Smart Life app and click the 'Scan' button in the upper right corner of the App Home page.
  2. Scan the QR code on page 20 of the Quick Start Guide (or the one shown in the video).
  3. The app should automatically detect the 'Multi-Circuit Power Meter'. Click 'Add'.
  4. Follow the prompts to ensure the indicator is blinking green.
  5. Enter your home 2.4GHz Wi-Fi account and password and click 'Next'.
  6. Wait for the device to be added and click 'Done'.
Smart Life App Scan Method
Screenshots showing the 'Scan' button and device detection in the Smart Life app.

7.3. Configuration Method 2 (Bluetooth Auto-Discovery)

  1. Power on the power clamp.
  2. Make sure the LED indicator is flashing green. If not, press and hold the reset button for 5 seconds until the LED flashes red 3 times quickly.
  3. Open the Smart Life app and turn on Bluetooth on your phone.
  4. The app should automatically detect the device and prompt you to add it. Click 'Add'.
  5. Follow the prompts to ensure the indicator is blinking green.
  6. Enter your home 2.4GHz Wi-Fi account and password and click 'Next'.
  7. Wait for the device to be added and click 'Done'.
Smart Life App Bluetooth Auto-Discovery Method
Screenshots showing Bluetooth prompts and device auto-discovery in the Smart Life app.

7.4. Configuration Method 3 (Manual Add)

  1. Turn on Wi-Fi and Bluetooth on your phone.
  2. Open the Smart Life app and click the '+' on the top right of the home page to add a device.
  3. Find the 'Energy' option and click 'Switch Module (Wi-Fi)' in the subdirectory 'Breaker'.
  4. Enter your home 2.4GHz Wi-Fi account and password and click 'Next'.
  5. Confirm the indicator is blinking quickly.
  6. Wait for the device to be added and click 'Done'.
Smart Life App Manual Add Method
Screenshots showing manual device addition via the Smart Life app.

8. LED Indicator Status

The LED status provides important information about the Power Meter's operational state:

LED StatusWhat it means
Green LED blinkingWait for pairing
Green LED solid onDevice has connected to cloud.
Red LED solid onDevice is connected to the router, but failed to connect to the cloud.
Red LED blinkingWi-Fi has been configured, but failed to connect to the router.

9. Troubleshooting

Device Reset

Press and hold the reset button for 5 seconds until the LED indicator flashes red 3 times quickly to restore the Power Meter to default factory settings (energy data will not be cleared).

If you want to clear the energy data, please delete the device and wipe data on the app and then add it again.

Network Connection Issues

Refer to the LED Indicator Status table above to diagnose network issues. Ensure your Wi-Fi network is 2.4GHz, as 5GHz is not supported. If the device fails to connect to the cloud or router, try resetting the device and reconfiguring the network.

10. User Tips

  • For accurate readings, always ensure the CT clamp arrows are pointing in the correct direction (towards the breakers for main lines, towards the load/inverter for sub-circuits).
  • If monitoring circuits with energy generation (e.g., solar), remember to manually set the phase in the app settings after wiring to ensure correct power measurement.
  • Regularly check the Smart Life app for firmware updates to ensure optimal performance and access to new features.

11. Maintenance

The EARU Smart WiFi Multi-Circuit Power Energy Meter is designed for low maintenance. Keep the device clean and free from dust. Ensure all connections remain secure. Do not attempt to open or repair the device yourself; contact qualified personnel for any servicing needs.

12. Warranty and Support

For detailed warranty information and technical support, please refer to the official user manual PDF available at: User manual (PDF). This document contains comprehensive information regarding product guarantees, troubleshooting, and contact details for customer service.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.