Introduction
Thank you for choosing the K&F Concept O254A4+BH-36 Professional Camera Tripod. This lightweight and versatile tripod is designed for photographers and videographers seeking stability and flexibility for various shooting scenarios, including DSLRs, mirrorless cameras, action cameras, and smartphones. With a maximum extended length of 165cm and a robust load capacity of 20kg, it features a 360° panoramic ball head, monopod conversion, and an inverted center column for low-angle shots.

Package Contents
Please check that all the following items are included in your package:
- K&F Concept O254A4 Professional Tripod
- BH-36 360° Ball Head
- Quick Release Plate
- Smartphone Holder
- Carrying Bag
- Instruction Manual (this document)
Setup Guide
1. Attaching the Ball Head
The BH-36 ball head typically comes pre-attached. If not, screw the ball head onto the 3/8" screw thread on the tripod's center column until secure. Ensure it is tightened firmly to prevent wobbling.

2. Extending the Tripod Legs
- Unlock the leg angle adjustment locks at the top of each leg to set the desired spread. The tripod offers multiple leg angle positions for stability on uneven terrain.
- Twist the spiral type quick locking system on each leg section counter-clockwise to loosen.
- Extend the leg sections to the desired height.
- Twist the quick locking system clockwise to lock each section firmly in place.


3. Mounting Your Camera or Smartphone
- For Cameras: Detach the quick release plate from the ball head by loosening the locking knob. Screw the quick release plate onto the 1/4" screw thread on the bottom of your camera. Ensure it is tight. Slide the camera with the attached quick release plate back into the ball head clamp and secure it with the locking knob.
- For Smartphones: Attach the provided smartphone holder to the quick release plate or directly to the 1/4" screw thread on the ball head (if applicable). Secure your smartphone firmly within the holder.


Operating Instructions
1. Adjusting Tripod Height
The tripod's height can be adjusted by extending the leg sections (as described in Setup) and by raising or lowering the center column. To adjust the center column, loosen the center column locking knob, raise or lower the column to the desired height, and then tighten the knob firmly.

2. Using the BH-36 Ball Head
The BH-36 ball head allows for flexible positioning of your camera. Loosen the main locking knob to adjust the camera's angle freely. Once the desired angle is achieved, tighten the knob to secure the camera. For panoramic shots, loosen the panoramic base locking knob to rotate the camera 360° horizontally without affecting the tilt angle, then tighten to lock.

3. Monopod Conversion
One of the tripod legs can be detached and combined with the center column to form a monopod. To do this, unscrew the designated leg (usually marked) from the tripod spider. Then, unscrew the center column from the tripod and attach it to the detached leg. This provides a portable support solution for situations where a full tripod is not feasible.

4. Inverted Center Column for Low-Angle Shooting
For extreme low-angle photography or macro shots, the center column can be inverted. To do this, fully extend and remove the center column from the tripod. Reinsert the center column upside down into the tripod spider and secure it. You can then attach your camera to the ball head, which will now be positioned below the tripod's base.

Maintenance
- Cleaning: Wipe down the tripod with a soft, damp cloth after each use, especially if used in dusty, sandy, or wet environments. Avoid harsh chemicals.
- Lubrication: Periodically check leg locks and moving parts. If they become stiff, apply a small amount of silicone-based lubricant. Do not over-lubricate.
- Storage: Store the tripod in its carrying bag in a dry, cool place away from direct sunlight and extreme temperatures.
- Inspection: Regularly inspect all screws, knobs, and leg locks for tightness. Tighten any loose components to ensure stability and safety.
Troubleshooting
- Problem: Tripod is unstable or wobbles.
- Solution: Ensure all leg sections are fully extended and their quick locks are securely tightened. Check that the center column locking knob is firm. Verify that the camera/ball head is properly mounted and tightened. Ensure legs are spread evenly on a flat surface, or adjusted for uneven terrain.
- Problem: Leg sections are difficult to extend or retract.
- Solution: The spiral quick locks might be too tight or too loose. Adjust them to the correct tension. Clean any dirt or debris from the leg sections and apply a small amount of silicone lubricant if necessary.
- Problem: Ball head movement is stiff or jerky.
- Solution: Loosen the main locking knob slightly. If the issue persists, the ball head may require cleaning or a very light application of specialized lubricant (consult K&F Concept support if unsure).
Specifications

| Feature | Specification |
|---|---|
| Model Number | KF09.153 (O254A4) |
| Type | Professional Tripod |
| Material | Aluminum Alloy |
| Leg Sections | 4 |
| Tube Diameter | 2.8 cm / 1.1 inches |
| Max Extended Length | 1650 mm / 64.96 inches |
| Folded Length | 410 mm / 14.1 inches |
| Net Weight (Tripod only) | 1.32 kg / 2.91 lbs |
| Max Load Capacity | 20 kg / 44 lbs |
| Compatibility | Video Camera, Action Cameras, 360° Video Camera, Point & Shoot Cameras, Special Camera, DSLRs, Smartphones, Mirrorless System Camera, Digital Cine Cameras |
| Feature | Specification |
|---|---|
| Model Number | BH-36 |
| Max Load Capacity | 20 kg / 44.09 lbs |
| Net Weight | 0.21 kg / 0.46 lbs |
| Height | 8 cm / 3.15 inches |
| Ball Diameter | 3.6 cm / 1.5 inches |
| Bottom Connection | 3/8" Screw Thread |
| Material | Synthetic Nylon (body), Aluminum (quick release plate) |
User Tips
- For maximum stability, always extend the thickest leg sections first and keep the center column as low as possible.
- When shooting in windy conditions, consider hanging a weight (e.g., your camera bag) from the hook at the bottom of the center column for added stability.
- Practice quick release plate attachment and detachment to ensure smooth transitions during shoots.
- Utilize the 360° panoramic scale on the ball head for precise alignment when stitching multiple photos for panoramas.
Warranty and Support
K&F Concept products are designed for durability and performance. For specific warranty details, product registration, or technical support, please refer to the official K&F Concept website or contact their customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Manufacturer: K&F CONCEPT
Origin: Mainland China