1. Product Overview
This manual provides instructions for the Scimagic-RC ECOSTAR compatible garage door remote control. This remote operates on a 433MHz frequency using rolling code technology, ensuring high security. It is designed to be compatible with specific ECOSTAR, Liftronic, and Portronic garage door opener models.
Figure 1: Front view of the remote control.
Video 1: Demonstration of the remote control's physical features and button presses.
2. Compatibility
This remote control is compatible with the following models:
- Remote Control Models: ECOSTAR RSC2-433, ECOSTAR RSE2-433, ECOSTAR RSZ1
- Receiver/Opener Models: Liftronic 500, Liftronic 700, Liftronic 800, Portronic D5000, Portronic D2500, Portronic S4000
Important: Access to your receiver/opener is required for programming. Please ensure your existing remote control matches the appearance shown in the product images, and your opener model is listed above. This new remote is not compatible with other remote types or the ECOSTAR BS series (e.g., Liftronique 800-2, Liftronique 700-2, RSC433-BS, RSZ433-BS).
Figure 2: Compatible remote and opener models.
Figure 3: Detailed compatibility with various Liftronic and Portronic models.
Figure 4: List of incompatible remote and opener models.
3. Setup and Programming
To register your new remote control, you must program it to your garage door receiver. This process typically involves accessing the receiver unit on your garage door opener.
Programming Steps:
- Access Receiver: Open your garage door opener's receiver unit. This is usually located under the motor cover or in a separate box next to the motor.
- Press Programming Button: Locate and press the programming button on the receiver. This button is commonly labeled as 'ENR', 'MEMO', or 'PROG'.
- Hold Button (if necessary): For some receiver models, you may need to press and hold the programming button.
- Observe LED: The LED indicator on the receiver will light up or change its state, signaling that it has entered programming mode.
- Activate New Remote: Press a button on your new remote control for one second, then release it.
- Confirm Programming: The receiver's LED will change again (e.g., light differently or turn off) to confirm successful programming.
- Exit Programming Mode: Wait a few seconds for the receiver to automatically exit programming mode.
Congratulations! Your new remote control is now programmed.
Figure 5: Visual guide to the remote control programming process.
4. Operation
Once programmed, simply press the desired button on your remote control to operate your garage door opener. The remote has 4 channels, allowing you to control up to 4 different compatible devices if programmed accordingly.
5. Maintenance
Battery Replacement:
The remote control is powered by a 12V 27A or CR2032 battery. When the remote's range decreases significantly or the LED indicator on the remote does not light up when a button is pressed, it's time to replace the battery. To replace, carefully open the remote casing (usually by unscrewing small screws on the back or prying open a seam) and insert a new battery of the same type, observing polarity.
General Care:
- Keep the remote control dry and away from extreme temperatures.
- Avoid dropping the remote or subjecting it to strong impacts.
- Clean the remote with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners.
6. Troubleshooting
Remote not working after programming:
- Check Compatibility: Double-check that your garage door opener model is explicitly listed as compatible. Incompatible models (e.g., Hormann Prolift 600-2, ECOSTAR BS series) will not work.
- Verify Programming Steps: Carefully repeat the programming steps, ensuring you press the correct buttons on both the receiver and the new remote. Ensure the receiver's LED responds as expected.
- Receiver Access: Confirm you have proper access to the receiver unit. Some users find this challenging.
- Battery Check: Ensure the remote's battery is correctly installed and has sufficient charge.
- Range: Test the remote within the specified working range (10-50m in open space). Obstacles can reduce this range.
Remote's LED not lighting up:
- Replace the battery.
7. Specifications
| Feature | Specification |
|---|---|
| Brand Name | Scimagic-RC |
| Model Number | ecostar rse2 (compatible with RSC2-433, RSE2-433, RSZ1) |
| Encoding Method | Rolling code |
| Number of Channels | 4 |
| Frequency | 433.92MHz (433MHz) |
| Working Range | 10-50 meters (open space) |
| Power Supply | 12V 27A / CR2032 battery |
| Modulation Mode | ASK (AM) |
| Transmission Power | ≤ 100mW |
| Working Temperature | -20°C to +50°C |
| Security | Dynamic code (non-copyable) |
| Dimensions | 54*30*14mm / 55*45*8mm |
| Certification | CE |
8. User Tips
- Always confirm your garage door opener's model number and frequency before purchasing a replacement remote to ensure compatibility.
- Keep the programming instructions handy, as accessing the receiver is a key step that can vary slightly between opener models.
- If you experience issues, try replacing the battery first, then re-attempt the programming steps carefully.
9. Warranty and Support
This product typically comes with a 1-year warranty from the store. For further assistance or detailed inquiries, please refer to the official user manual PDF available at User manual (PDF). You may also contact the manufacturer, Shenzhen Scimagic Development Technology Co.Ltd, at their address: Honghai Gebu Building 2301, Baoan Road, Songgang Baoan District Shenzhen Guangdong China.
