1. Introduction
Thank you for choosing the FYHXele 32-Inch 2K 165Hz IPS Gaming Monitor. This user manual provides important information regarding the safe operation, installation, and maintenance of your monitor. Please read this manual thoroughly before using the product and keep it for future reference.
2. Safety Precautions
Read and observe the following warnings and information below:
- Before cleaning, always unplug your monitor. It is recommended that you use a dry cloth or lightly damp cloth to clean your monitor. Dry cloth is, however, the safest. If using a damp cloth, wait for your monitor to completely dry before plugging it in again.
- Do not use alcohol or ammonia-based cleaner and/or liquids to clean your monitor.
- This monitor features ventilation openings on the back of the unit. Avoid blocking these openings to prevent the monitor from overheating.
- Avoid placing this monitor near any heat sources, e.g., portable heaters or heating vents, as this may cause damage to your monitor.
- Do not spray cleaner and/or any kind of liquid directly onto the monitor's screen or any part of the monitor.
- Do not insert anything into any part of the monitor, especially the ventilation openings.
- Always make sure your monitor is placed on a secure, level surface to prevent it from falling and sustaining damage.
- Unplug your monitor during any extended periods of non-use.
- Do not place heavy items on the monitor or monitor cables.
- Do not attempt to disassemble or remove parts from the monitor. Any disassembly or modification not performed by an authorized technician can result in damage to the monitor and/or possible exposure to high voltage electricity which may lead to serious injury or death.
FYHXele shall not be held responsible for injury or damage of products or persons due to failure to adhere to the aforementioned precautions or any others noted hereafter.
Image Persistence
This product is not designed to have fixed image patterns on the screen for extended periods of time.
CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This "bolt of lightning" indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering.
The "exclamation point" calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.
WARNING:
To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.
3. Product Overview
3.1 Monitor Buttons
Note: The location and names of the function buttons and power button on the monitor may vary according to monitor model, and some buttons may not be available for some models.
Base Controls - Type 1
| No. | Description |
|---|---|
| 1 | Go to the main menu. |
| 2 | Enter the source mode. |
| 3/4 | HotKey 1, 2 buttons. Press to activate user defined hotkey function. |
| 5 | In the powered-off state, pressing the button powers on the device; in the powered-on state, pressing the button normally enters the mode switching menu, and long-pressing for 3 seconds powers off the device. |
Base Controls - Type 2
| No. | Description |
|---|---|
| 1 (M) | Display the OSD menu or enter sub-menus. |
| 2 (▼) | Press to move down in the menus. |
| 3 (▲) | Press to move up in the menus. |
| 4 (E) | Press to exit. |
| 5 (Power) | Power on/off. |
Base Controls - Type 3
| No. | Item | Description |
|---|---|---|
| 1 | Power button/indicator | Turns the monitor on/off. Blue indicates power on. Amber indicates standby/power saving mode. |
| 2 | Hotkey 1, 2 buttons | Press to activate user defined hotkey function. |
| 3 | Input button | Press to toggle input sources. |
| 4 | Navi/OK button | Press to activate the OSD menu, then use it as directional key to highlight the desired function. Press it again to enter a selection. |
Base Controls - Type 4
| No. | Item | Description |
|---|---|---|
| 1 | Menu/Navi/OK button | Press this button to turn the monitor on and off. Nudge right to open menu or confirm selection, nudge left to exit, nudge up and down to move up or down in menu. |
3.2 Monitor Ports
- DC-IN port: This port connects the power cord.
- DVI (Dual-Link) port: This 24-pin port is for PC (Personal Computer) DVI-D digital signal connection.
- HDMI port: This port is for connection with an HDMI compatible device.
- DisplayPort: This port is for connection for a DisplayPort compatible device.
- USB Type-C port: Connect the USB Type-C cable that came with your monitor to the computer. This port supports USB Power Delivery, Data, and DisplayPort video signal.
NOTE: USB Type-C is not supported on versions of Windows prior to Windows 10. This interface has different powers of 15W, 65W, 95W, so the output power of this interface is also different when charging. For specific interface power, please refer to the parameters when purchasing the display. - USB Type-A port: Connect your USB device.
- Audio Output: Insert one end of the audio cable into an external audio source.
Note: Different models are equipped with different ports, please check your monitor for specific ports.
Note:
If the monitor supports DisplayPort, it purposely supports G-Sync compatible/Freesync/Freesync Premium/Freesync Premium Pro/Adaptive-Sync (DP) support technology. This technology allows Freesync/Freesync Premium/Freesync Premium Pro/Adaptive-Sync (DP) supported graphics source to dynamically adjust display refresh rate based on typical content frame rates in order to eliminate stuttering and enhance low-latency display.
3.3 Indicator Light
Solid blue light indicates power is on and the monitor is operating normally. Flashing blue light indicates no video source, no horizontal or vertical signal has been detected or voltage is low. Please ensure your computer is on and all video cables are fully inserted and/or connected. *only for certain models
4. Installation
To install the monitor to your host system, please follow the steps as given below:
- Turn off your computer and unplug the power cord.
- Connect Video Cable:
- Make sure both the monitor and computer are powered-OFF.
- Connect the VGA cable to the computer. (Optional)
- Connect HDMI Cable (Only HDMI-input model) (Optional):
- Make sure both the monitor and computer are powered-OFF.
- Connect the HDMI cable to the computer.
- Connect DP Cable (Only DP-input model) (Optional):
- Make sure both the monitor and computer are powered-OFF.
- Connect the DP cable to the computer.
- Connect the Audio cable (only Audio input model) (optional).
- Connect the USB Type C Cable (only USB Type C input model) (Optional).
- Insert the monitor power cable into the power port at the back of the monitor.
- Plug the power cords of your computer and your monitor into a nearby electrical outlet.
- Select Power-off USB charge ON/OFF to enable/disable Power-off USB charge function. (Optional).
| Input Type | Cable Type | Note |
|---|---|---|
| HDMI (optional) | Ω (optional) | The location and names of the sockets on the monitor may vary according to monitor model, and some sockets may not be available for some models. |
| VGA IN (optional) | USB (optional) | |
| AUDIO IN (optional) | DP (optional) | |
| AUDIO OUT (optional) | USB Type C (Optional) |
5. OSD Setup
The On-Screen Display (OSD) Menu may be used to adjust your monitor's settings and appears on screen after turning on the monitor and pressing the M button.
Note:
When using the monitor for the first time, settings will automatically adjust to optimal settings according to your computer's configuration and parts etc.
- Press any one of the buttons (M, ▼, ▲, E, Power) to activate the navigation window.
- Press M to enter the OSD menu.
- Press ▼ or ▲ to browse functions.
- Highlight the desired function, then press M to enter the sub-menu.
- Press ▼ or ▲ to browse sub-menus, then press M to highlight the desired function.
- Press ▼ or ▲ to highlight an option, then press M to confirm the settings and exit the current screen.
- Press E to exit the current screen.
5.1 OSD Menu Functions (Type-1)
| Main Menu | Sub-Menu | Options | Description |
|---|---|---|---|
| Brightness | Brightness | 0~100 | Adjust display brightness |
| Contrast | 0~100 | Adjust display contrast | |
| ECO | Standard, Game, RTS, FPS, Movie, Text | Set visual mode | |
| DCR | On | Turn on DCR function | |
| Off | Turn off DCR function | ||
| Auto | Best for overall use | ||
| Image | Aspect | Wide | Set image aspect ratio to fullscreen |
| 4:3 | Set image aspect ratio to 4:3 | ||
| Color Temp. | Color Temp. | Warm, Cool, User | Set the display color temperature mode |
| RED | 0-100 | Customize the display screen RGB component according to preference | |
| BLUE | 0-100 | ||
| GREEN | 0-100 | ||
| OSD Setting | Language | English, Nederlands, Français, Deutsch, 한국, Español, Русский, Português, Turkce, Italiano, Polski, 简体中文, 日本語 | Set OSD language |
| OSD H. Position | 0~100 | Adjust the OSD Horizontal position | |
| OSD V. Position | 0-100 | Adjust the OSD Vertical position | |
| OSD Timer | 0~60 | Adjust OSD display time | |
| Transparency | 0-100 | Adjust OSD transparency | |
| Reset | Reset | None | Reset monitor configurations |
| Misc | Signal Source | HDMI1, HDMI2, DP | DP or HDMI signals input |
| Volume | 0-100 | Adjust audio volume | |
| Low blue ray | 0-100 | Set blue light filtering level | |
| FreeSync | On, Off | Turn on/off FreeSync | |
| Over Driver | Off, Low, Middle, High | Set the Over driver function |
5.2 OSD Menu Functions (Type-2)
| Main Menu | Sub-Menu | Description |
|---|---|---|
| Input Source | ->Auto Source | Switch the signal input to Auto Select, DP(1.4), HDMI1, or HDMI2. |
| ->DP | ||
| ->HDMI1 | ||
| ->HDMI2 | ||
| Brightness/Contrast | ->Brightness | Adjust the display brightness value from 0 to 100. |
| ->Contrast | Adjust the display contrast value from 0 to 100. | |
| ->Black Level | Adjust the Black Level value from 0 to 100. | |
| ->Sharpness | Adjust the Sharpness value from 0 to 100. | |
| ->Picture Mode | Select mode from Standard, User, Movie, Photo, RTS, FPS1, and FPS2. | |
| Color Setting | ->DCR | Turn dynamic contrast on/off. |
| ->Color Temperature | Select Color Temperature from Warm, Normal, Cool, sRGB, and User. | |
| ->Saturation | Adjust the Saturation value from 0 to 100. | |
| ->Low Blue Light | Adjust the Low Blue Light value from 0 to 100. | |
| Picture Quality Setting | ->Gamma | Select Gamma from Off, 1.8, 2.0, 2.2, 2.4 and 2.6. |
| ->Colour gamut | Turn color gamut on/off. | |
| ->HDR | Turn HDR on/off. | |
| ->MPRT | Turn MPRT on/off. | |
| ->Response Time | OFF/ON - Set the power led on and off. | |
| Display | ->Aspect Radio | Full screen/16:9/4:3 - Set the screen display size mode. |
| ->FreeSync(Adaptive Sync) | Turn FreeSync(Adaptive Sync) On or Off. | |
| Audio | ->Overdrive | Select Overdrive from Off, Low, Middle, and High. |
| ->Mute | Turn audio On or Off. | |
| ->Volume | Adjust audio volume from 0-100. | |
| OSD | ->Language | Change the OSD menu display language. |
| ->OSD H-Position | Adjust the range of 0-100, to adjust the horizontal position of the OSD. | |
| ->OSD V-Position | Adjust the range of 0-100, to adjust the vertical position of the OSD. | |
| ->OSD Transparency | Adjust the range of 0-100, to adjust the transparency of the OSD. | |
| ->OSD Time Out | Adjust the range of 5-60, To set automatic OSD exit time. | |
| Other | ->Off timer | Turn Off timer on/off. |
| ->Reset | Select Reset from Cancel or Confirm. | |
| ->Led Effect | Turn LED lights on the back on/off. |
Note:
Different models have different OSD versions. The functions of the OSD are subject to change due to version upgrades without prior notice.
6. ECO Modes and Gameplus
- Press any one of the buttons (M, ▼, ▲, E, Power) to activate the navigation window.
- Press ▼ to switch Gameplus modes. Choose the crosshair icon best suited for your game. These game icons are primarily designed to optimize your aim during shooting games, though they can be used for other scenarios.
Various crosshair options for Gameplus mode. - Press ▲ button to switch ECO modes. These modes (Standard, Text, Movie, Game, FPS, and RTS) can be used to optimize settings according to your activity. Standard mode is suitable for most activities.
*The function is only for certain models
7. Troubleshooting
The screen is blank
- Press power button to turn the monitor on.
- Confirm the brightness and contrast settings are set normally.
- Check if the Indicator Light is flashing. If so, there is no signal from your video source.
- If your source is a notebook or laptop, be sure that its settings are in mirror or extension mode and the device itself is powered on.
The image is out of focus
- Ensure the video cable is inserted properly at both ends.
The screen is flashing
- Try an alternative power source. Insufficient power may cause this issue.
- Ensure devices such as non-shielded speakers, fluorescent lighting, AC transformers, table fans, etc., are a safe distance away from your screen to avoid magnetic disturbances.
The color bleeds or visual effects appear unusual.
- If your screen is all red or blue, or any colors disappear, check to see that the cable is properly inserted. A loose connection can cause a bad signal.
- Try connecting to another video source for comparison.
The screen appears to be scrolling, rolling, or moving unusually.
- Check that your source frequency is within 48-144Hz.
- Reconnect and ensure your video cable is secure.
The monitor needs cleaning
- Make sure the monitor has been powered off before cleaning.
- Always use soft, non-abrasive cloth when cleaning.
- Use dry, non-abrasive cloth to gently remove debris or dust.
- If necessary, lightly dampen a non-abrasive cloth with water and gently clean the surface.
- Never use alcohol or ammonia-based cleaning solutions.
- Never spray liquid directly onto any part of the monitor.
The indicator light does not work
- Check if the power is on.
- Check if the power line connected with power.
Cannot plug and play.
- Inspect if the monitor is compatible with PC.
- Inspect if the graphics card is compatible with the monitor.
- Inspect if the pins in the interface are curved.
Dim image
- Adjust the brightness and contrast ratio.
Image jitter/moire pattern
- Nearby electric equipment may interfere with the monitor.
Light indicator is on or flashing, but there is no image displayed on screen
- Check if the monitor power is on.
- Check if the graphics card is installed properly.
- Check if the signal line connects securely with the monitor.
- Check if the pins in the interface are curved.
Color shortage (red, green, or blue)
- Inspect if the pins in the interface are curved.
Image position is not centered/the size is not right
- Please adjust Clock or Auto setting.
Color difference (colors are not optimized)
- Adjust RGB color or reset color temperature.
8. Specifications
| Feature | Specification |
|---|---|
| Model | 32-2K-165HZ |
| Display Size | 32 inches (31.5") |
| Resolution | 2560x1440 (2K QHD) |
| Refresh Rate | 165 Hz |
| Response Time | 1 ms (MPRT) |
| Panel Type | IPS |
| Display Ratio | 16:9 Widescreen |
| Viewing Angle | 178° (Horizontal) / 178° (Vertical) |
| Color Gamut | 100% sRGB, 90% DCI-P3 |
| Matrix Color Depth | 8 bit |
| Contrast Ratio | 1000:1 |
| Brightness | 400cd/m² |
| High-Dynamic Range | HDR400 |
| Refresh Rate Sync Technology | AMD FreeSync, G-Sync Compatible, VRR |
| Screen Surface | MATT |
| Screen Curvature | NONE |
| Interface Type | HDMI, DisplayPort (DP), USB Type-C (Full-function, 65W PD), USB-A, Audio Out |
| Built-in Speaker | Yes |
| Bracket Type | Ordinary Bracket |
| VESA Mount | 100x100mm |
| Application | Desktop |
| Language Support | English, Russian, Japanese, Korean, French, German, Spanish, Italian |
| Launch Date | 2022 |
9. User Tips
No specific user tips from reviews or Q&A were available for this product at this time. Please refer to the troubleshooting section for common issues.
10. Warranty and Support
For customer service, technical support, or warranty inquiries, please contact the manufacturer directly:
- Manufacturer: Shenzhen Fengyu Huaxin Technology Co., Ltd.
- Address: Room 517, 5th Floor, Building D, Shanhaiyunhui, No. 1067, Bantian Xuegang, Longgang District, Shenzhen, Guangdong Province, China
- Customer Service Email: support@fyhxele.com
- Website: www.fyhxele.com
For the latest user manuals and product materials, please check the manufacturer's website. A PDF version of this manual is also available for download: User Manual (PDF).