MESTEK WM710

Contents

MESTEK WM710 Pinless Wood Moisture Meter Instruction Manual

Model: WM710 | Brand: MESTEK

1. Introduction

The MESTEK WM710 is a non-destructive induction hygrometer designed for quick and accurate measurement of moisture content in various materials such as wood (softwood and hardwood), drywall, and masonry. It features multiple measurement modes, data locking, Max/Min value display, environmental temperature and humidity measurement, and a clear VA reverse display color screen. This manual provides detailed instructions for safe and effective use of the device.

MESTEK WM710 Pinless Moisture Meter front view
Figure 1: MESTEK WM710 Pinless Moisture Meter

2. Package Contents

Please check the package contents upon receipt to ensure all items are present:

  • 1 x MESTEK WM710 Host
  • 1 x Packaging Box
  • 1 x User Manual (Instructions)
  • 1 x Screwdriver
  • 1 x Plush Cloth Bag
Diagram showing the accessories included with the WM710
Figure 2: Included Accessories

3. Product Overview

The MESTEK WM710 features a user-friendly interface with a VA reverse display color screen and intuitive buttons. The device is equipped with a high-frequency electromagnetic wave sensor for non-destructive measurements.

WM710 front and back view with labeled parts and functions
Figure 3: Function Panel and Device Components

Key Components:

  • Environmental temperature and humidity probe: Located at the top of the device.
  • Humidity sensor: Integrated for ambient humidity readings.
  • VA reverse display color screen: High-definition screen for clear readings.
  • Battery cover: Located on the back for battery installation.
  • Power button: To turn the device on/off.
  • Mode selection key (SEL): To switch between measurement material modes.
  • Min/Max value lock (MIN MAX): To display minimum and maximum recorded values.
  • Data locking (HOLD): To freeze the current measurement on the display.
  • Celsius/Fahrenheit switching (°C/°F): To change temperature units.
  • Zeroing key (ZERO): To perform zero point calibration.
Diagram showing the high-frequency electromagnetic wave sensor on the back of the WM710
Figure 4: High Frequency Electromagnetic Wave Sensor

The high-frequency electromagnetic wave sensor allows for non-destructive measurements, penetrating a maximum depth of 20mm. For accurate readings, the test object's thickness should be greater than 20mm and the measurement area greater than 40x40mm.

4. Setup

4.1 Battery Installation

  1. Locate the battery cover on the back of the device.
  2. Use the provided screwdriver to open the battery cover.
  3. Insert 3 x AAA 1.5V batteries, ensuring correct polarity.
  4. Replace the battery cover and secure it with the screw.

Note: Batteries are not included in the package.

5. Operating Instructions

5.1 Power On/Off

  • Press the Power button (Power button icon) to turn the device on.
  • Press and hold the Power button to turn the device off.
  • The device will automatically shut down after 10 minutes of inactivity to conserve battery.

5.2 Measurement Mode Selection

The WM710 supports four measurement modes: Drywall, Masonry, Softwood, and Hardwood.

  1. Turn on the device.
  2. Short press the SEL button to cycle through the measurement modes. The selected mode will be indicated on the display.
Video 1: 4-in-1 Measurement Mode Conversion Demonstration
Images showing the WM710 testing various materials: hardwood, softwood, drywall, masonry
Figure 5: Multiple Material Testing Capabilities

5.3 Zero Calibration

Perform zero point calibration based on the current air humidity or the humidity of the measured object.

  • With the device powered on, press the ZERO button to clear the current reading and perform a zero calibration.

5.4 Temperature Unit Switching (°C/°F)

The device automatically measures ambient temperature and humidity. You can switch between Celsius and Fahrenheit units.

  • Short press the °C/°F button to convert the temperature display between Celsius and Fahrenheit.
WM710 demonstrating Celsius/Fahrenheit temperature unit switching
Figure 6: Celsius/Fahrenheit Switching

5.5 Data Hold (HOLD)

  • Press the HOLD button to freeze the current measurement on the display.
  • Press the HOLD button again to release the data hold function.

5.6 Max/Min Value (MIN MAX)

  • Press the MIN MAX button to display the maximum recorded moisture value.
  • Press it again to display the minimum recorded moisture value.
  • Press it a third time to return to real-time measurement.

5.7 Sound and Light Alarm

The device provides visual and audible alarms based on moisture levels:

  • Green light: DRY (Low moisture)
  • Yellow light: RISK (Moderate moisture, caution advised)
  • Red light: WET (High moisture, potential issue)

5.8 Performing a Measurement

  1. Select the appropriate material mode (Drywall, Masonry, Softwood, Hardwood) using the SEL button.
  2. Place the back of the device (where the sensor is located) flat against the surface of the material to be measured.
  3. Ensure the contact area is sufficient (greater than 40x40mm) and the material thickness is at least 20mm for optimal results.
  4. Read the moisture content directly from the VA reverse display color screen. The display also shows ambient temperature and humidity.
WM710 in use, testing wood moisture
Figure 7: Testing Wood Moisture
WM710 in use, testing a cement mortar layer
Figure 8: Testing Cement Mortar Layer
WM710 in use, testing drywall
Figure 9: Testing Drywall
WM710 in use, testing masonry
Figure 10: Testing Masonry

5.9 Humidity Display Comparison Table

The following table provides a general guide for interpreting moisture readings in different modes:

Measurement modeGreen/DRYYellow/RISKRed/WET
DRYWALL0.0 ~ 17.918.0 ~ 35.936.0 ~ 54.0
MASONRY0.0 ~ 11.912.0 ~ 23.924.0 ~ 36.0
SOFTWOOD0.0 ~ 31.932.0 ~ 63.964.0 ~ 100
HARDWOOD0.0 ~ 31.932.0 ~ 63.964.0 ~ 100
Table showing humidity display comparison for different measurement modes
Figure 11: Humidity Display Comparison Table

6. Maintenance

  • Keep the device clean and dry. Use the provided plush cloth bag for storage.
  • Avoid exposing the device to extreme temperatures or high humidity.
  • If the device will not be used for an extended period, remove the batteries to prevent leakage.
  • Do not attempt to disassemble or repair the device yourself. Contact qualified personnel for service.

7. Troubleshooting

7.1 Common Issues

  • Device does not power on: Check battery installation and ensure batteries are not depleted. Replace if necessary.
  • Inaccurate readings: Ensure the device is properly calibrated (use the ZERO function). Verify the correct material mode is selected. Ensure the sensor is in full contact with the material and the material meets the minimum thickness and area requirements.
  • Low battery reminder: The display will show a low battery icon. Replace batteries promptly.

If you encounter persistent issues, please refer to the warranty and support information.

8. Specifications

ParameterValue
Product nameNon-destructive induction hygrometer
Measuring rangeSoftwood and hardwood: 0%~ 100%. Humidity measurement of gypsum wall and masonry wall is relative value.
Measurement accuracySoftwood, hardwood, 4%
Maximum measured thickness4/3 inch (20mm)
Temperature measurement±2.0°C/3°F (0~45°C/32~113°F) ±2.5°C/4°F (-10~0°C/45~60°C/14~32°F, 113~140°F)
Moisture measurement±5.0%RH (20%~95%)
Automatic shut-down10 minutes
IndicatorA reverse color screen
Battery1.5V X 3 AAA (not include)
Operational currentAbout 20mA
Working temperature0-50°C
Working humidity0%-70%RH
Storage environment-10~60°C (5%-75%RH)
Size165*63*32mm
WeightAbout 164g (excluding battery)
Table of technical parameters for the WM710
Figure 12: Technical Parameters

9. User Tips

  • For consistent readings, always ensure the sensor is placed flat against the surface and covers an area of at least 40x40mm.
  • Calibrate the device (ZERO function) in the environment where you will be taking measurements, or against a known dry reference material, for best accuracy.
  • When measuring different materials, remember to switch to the correct mode using the SEL button.
  • The sound and light alarm is a quick indicator; pay attention to the specific moisture percentage on the display for precise information.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt as proof of purchase.


Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.