EPSON EM-326, EM-323

Contents

Micro 42MM Stepper Motor User Manual

Models: EM-326 (with Belt Pulley) & EM-323 (with Copper Gear)

1. Introduction

This manual provides detailed instructions and specifications for the Micro 42MM Stepper Motor, designed for precision applications such as printer paper feed mechanisms. Two models are covered: Model A (EM-326) featuring a belt pulley, and Model B (EM-323) equipped with a copper gear. Both are 2-phase, 4-wire hybrid stepper motors.

Overview of Micro 42MM Stepper Motors, showing Model A with a belt pulley and Model B with a copper gear.
Figure 1: Overview of Model A (left) and Model B (right) Stepper Motors.

2. Specifications

The following tables detail the specifications for both stepper motor models:

2.1. Model A (EM-326) - With Belt Pulley

FeatureSpecification
Type2-phase 4-wire Stepper Motor (HYBRID)
ModelEPSON EM-326 98310
Motor Specification42mm
Body Height (including bracket)24 mm
Step Angle1.8 degrees
Coil Resistance4.5 ohms
Wire Length370 mm
Weight181 grams
Shaft Diameter4 mm
Shaft Length12.7 mm
Belt Wheel Diameter13 mm
Belt Wheel Height9.5 mm
CertificationUL
Detailed dimensions of Model A stepper motor, showing motor height, wire length, and belt wheel dimensions.
Figure 2: Model A (EM-326) with detailed dimensions.

2.2. Model B (EM-323) - With Copper Gear

FeatureSpecification
Type2-phase 4-wire Stepper Motor (HYBRID)
ModelEPSON EM-323 98290
Motor Specification42mm
Body Height (including bracket)22.3 mm
Step Angle3.75 degrees
Coil Resistance11.5 ohms
Wire Length260 mm
Weight160.3 grams
Shaft Diameter3 mm
Shaft Length16.8 mm
Copper Gear Teeth16
Copper Gear Diameter7 mm
Copper Gear Height4.4 mm
CertificationUL
Detailed dimensions of Model B stepper motor, showing motor height, wire length, and copper gear details.
Figure 3: Model B (EM-323) with detailed dimensions.
Side view comparison of Model A and Model B stepper motors, highlighting shaft diameters and lengths.
Figure 4: Shaft diameter and length comparison for Model A and Model B.

3. Setup and Installation

3.1. Mounting

Both models come with an original bracket for easy mounting. Ensure the motor is securely fastened to a stable surface to prevent vibration during operation. Refer to the dimensions in the specifications section for proper fitment.

3.2. Wiring

These are 2-phase, 4-wire stepper motors. They require a compatible stepper motor driver. The wiring connections are typically as follows:

  • A+ (Red wire)
  • A- (Blue wire)
  • B+ (Black wire)
  • B- (Gray wire)

Connect these wires to the corresponding terminals on your stepper motor driver. Always consult your driver's manual for specific wiring instructions.

Wiring diagram for the 2-phase 4-wire stepper motor, showing A+, A-, B+, B- connections.
Figure 5: Stepper Motor Wiring Diagram.

4. Operating Instructions

To operate the stepper motor, you will need a stepper motor driver and a controller (e.g., microcontroller, PLC) to generate step and direction signals.

  1. Power Supply: Connect a suitable DC power supply to your stepper motor driver. Ensure the voltage and current ratings are appropriate for both the motor and the driver.
  2. Driver Configuration: Configure your stepper motor driver settings (e.g., current limit, microstepping, step mode) according to the motor's specifications and your application requirements.
  3. Control Signals: Connect the step and direction pins of your controller to the corresponding inputs on the stepper motor driver.
  4. Software Control: Program your controller to generate the desired step pulses and direction signals to achieve the required motor movement.

The step angle for Model A is 1.8 degrees, and for Model B is 3.75 degrees. This determines the resolution of movement per step. Microstepping can be used with your driver to achieve finer control.

5. Maintenance

Stepper motors are generally low-maintenance devices. Follow these guidelines to ensure longevity:

  • Keep Clean: Periodically clean the motor and its surroundings to prevent dust and debris buildup, especially around the shaft and any moving parts (pulley/gear).
  • Check Connections: Ensure all electrical connections remain secure and free from corrosion. Loose connections can lead to erratic behavior or motor damage.
  • Avoid Overheating: Ensure adequate ventilation around the motor, especially during prolonged operation at high currents. Overheating can reduce motor lifespan.
  • Inspect for Wear: For Model A, check the belt pulley for any signs of wear or damage. For Model B, inspect the copper gear for tooth wear.

6. Troubleshooting

If you encounter issues with your stepper motor, consider the following troubleshooting steps:

  • Motor Not Moving:
    • Verify power supply to the driver is correct and stable.
    • Check all wiring connections (A+, A-, B+, B-) for correctness and continuity.
    • Ensure the step and direction signals from the controller are being generated correctly.
    • Confirm the driver's current limit is set appropriately for the motor.
  • Erratic Movement or Missed Steps:
    • Reduce the motor speed or acceleration settings in your controller.
    • Increase the current limit on the driver (within motor specifications).
    • Check for mechanical binding or excessive load on the motor shaft.
    • Ensure the power supply can deliver sufficient current.
  • Motor Overheating:
    • Reduce the driver's current setting if it's too high.
    • Ensure adequate ventilation or consider adding a heatsink if operating continuously at high loads.
    • Check for short circuits in the motor windings or wiring.

7. User Tips

  • Driver Selection: Always pair your stepper motor with a compatible stepper motor driver. The driver's current output should match the motor's rated current for optimal performance.
  • Microstepping: Utilize microstepping features on your driver for smoother operation and reduced resonance, especially in applications requiring precise positioning.
  • Initial Testing: When first setting up, start with low speeds and currents, gradually increasing them to find the optimal operating parameters for your specific application.
  • Load Consideration: Ensure the mechanical load on the motor does not exceed its torque capabilities to prevent missed steps or stalling.

8. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your point of purchase. For technical support or inquiries, please contact the seller directly. The seller for this product is Parts Hub Store.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.