Interest Maker LCR-MF9

Contents

LCR-MF9 Multi-function Tester User Manual

Your comprehensive guide to operating the LCR-MF9 Multi-function Tester.

1. Introduction

The LCR-MF9 is a versatile multi-function tester designed for automatic detection and measurement of various electronic components. It features a 1.8-inch TFT LCD display for clear graphical results and includes an IR decoder function. This manual provides detailed instructions for safe and effective use of your device.

LCR-MF9 Multi-function Tester with included accessories
Figure 1: LCR-MF9 Multi-function Tester and accessories.

2. Safety Information

  • Discharge Capacitors: Always ensure capacitors are fully discharged before connecting them to the tester. Failure to do so can damage the tester.
  • Battery Voltage: Do not use the tester to measure batteries with voltage higher than 4.5V, as this may damage the device.
  • Active Circuits: The instrument provides active output. Do not use the test leads to test components within a charged circuit board, as this can easily damage the instrument.
  • KAA Test Area Caution: The KAA test area has an output voltage of 20V. If a capacitor is accidentally placed here, it must be discharged before being moved to the transistor test area. Placing a charged capacitor from the KAA area directly into the transistor test area will cause immediate damage to the instrument, potentially damaging test pins or causing complete shutdown.
Warning about discharging capacitors and not measuring batteries above 4.5V
Figure 2: Important safety warnings regarding capacitor discharge and battery testing.

3. Product Overview

The LCR-MF9 Multi-function Tester is a compact and portable device with a 1.8-inch TFT LCD display. It is designed for easy identification and measurement of various electronic components.

3.1. Components and Layout

LCR-MF9 Multi-function Tester with labeled parts
Figure 3: LCR-MF9 Multi-function Tester labeled with its main parts.
  • TFT Display: 1.8-inch color LCD for displaying measurement results graphically.
  • IR Receiver Window: For infrared remote control decoding.
  • Test Button: Initiates component testing and powers on the device.
  • Transistor Test Area: ZIF socket for testing various transistors, capacitors, resistors, diodes, and other components.
  • Zener Diode Test Area (KAA): Dedicated area for testing Zener diodes, especially those higher than 5V.
  • USB Charging Port: Micro USB port for charging the internal battery.

3.2. Dimensions

The LCR-MF9 has compact dimensions, making it easy to handle and store.

  • Dimensions: 60mm x 90mm x 27mm
LCR-MF9 Multi-function Tester dimensions
Figure 4: Physical dimensions of the LCR-MF9 tester.

4. Specifications

The LCR-MF9 Multi-function Tester offers a wide range of measurement capabilities for various electronic components.

Component TypeRangeParameter Description
BJTN/AhFE (DC Current Gain), Ube (Base-Emitter Voltage), Ic (Collector Current), Iceo (Collector Cut-off Current), Ices (Collector Short Current), Uf (Forward Voltage of protecting diode)
DiodeForward voltage <4.50VForward voltage drop, junction capacitance, reverse leakage current
Double DiodeForward voltage <4.50VForward voltage
Zener Diode0.01-4.50V (Transistor Test Area)
0.01-20V (Zener Diode Test Area)
Forward voltage drop, reverse breakdown voltage
JFETN/ACg (Gate Capacitance), Id (Drain Current) at Vgs (Gate to Source Threshold Voltage), Uf (Forward Voltage of protecting)
IGBTN/ADrain current Id under Vgs, protection diode forward voltage drop Uf
MOSFETN/ATurn-on voltage Vt, gate capacitance Cg, drain resistance Rds, protection diode forward voltage drop Uf
ThyristorGate trigger current <6mAGate turn-on voltage
TriacGate trigger current <6mAGate turn-on voltage
Capacitor25pF-100mFCapacitance Value, Equivalent Series Resistance ESR, Vloss
Resistor0.01-50MΩResistance
Inductor0.01mH-20HInductance, DC Resistance
Battery0.1-4.5VVoltage value, battery polarity

General Specifications:

  • Operating Mode: Auto Range
  • Operating Temperature: 0 - 40 ℃
  • DC Voltage (Internal Battery): 3.7V
  • Display Type: Digital Display (160x128 TFT LCD)
  • Certification: CE
  • DIY Supplies: Electrical
  • Battery Included: No (internal rechargeable Li-ion battery)

5. Setup

5.1. Charging the Battery

The LCR-MF9 is equipped with a built-in rechargeable Li-ion battery. Use the provided Micro USB cable to connect the tester to an external 5V power supply or a USB port for charging.

USB charging port on the LCR-MF9 tester
Figure 5: The Micro USB charging port.

Charging Indicator: When the charging indicator light is red, the device is charging. A green light indicates that charging is complete.

5.2. Activating the KAA Test Area

The KAA (Zener Diode) test area is turned off by default. To activate it:

  1. Ensure the tester is powered off.
  2. Press and hold the TEST key for approximately 15 seconds.
  3. The lower left corner of the screen will change from "KAA OFF" to "KAA ON", indicating that the KAA test area is now active.
  4. This setting is automatically saved and does not need to be repeated.
Warning about Zener diode test area
Figure 6: Warning regarding the Zener Diode test area.

6. Operating Instructions

6.1. Power On and Basic Measurement

To power on the tester and initiate an automatic measurement:

  1. Ensure the tester is powered off.
  2. Short press the TEST key. The tester will turn on and automatically begin a measurement.
LCR-MF9 power on and measurement interface
Figure 7: The display after powering on, showing 'Testing...' and battery voltage.

6.2. Component Testing

The LCR-MF9 automatically detects and measures various components. For accurate results, ensure components are properly inserted into the ZIF socket (transistor test area).

  1. With the tester powered off or after a completed test, place the component into the transistor test area of the ZIF socket. The pins do not need to be in a specific order, as the tester will automatically identify them.
  2. Press the locking handle to secure the component.
  3. Short press the TEST key. The tester will automatically measure and display the component parameters and pinout graphically.

The tester supports a wide range of components, including:

  • NPN and PNP Bipolar Transistors (BJTs)
  • N-channel and P-channel MOSFETs
  • JFETs
  • Diodes (including double diodes, Zener diodes)
  • N and P-IGBTs
  • Resistors
  • Inductors
  • Capacitors
  • Thyristors
  • Triacs
LCR-MF9 testing an N-D-MOS component with test leads
Figure 8: Testing an N-D-MOS component using test leads.
LCR-MF9 display examples for various components
Figure 9: Examples of component test results on the LCR-MF9 display.
LCR-MF9 display examples for various transistors
Figure 10: Examples of transistor test results on the LCR-MF9 display.

6.2.1. Zener Diode Testing

For Zener diodes, especially those with breakdown voltage higher than 5V, use the dedicated Zener diode test area (KAA). Ensure the KAA test area is activated as described in Section 5.2.

  1. With the device turned off or after a completed test, place the Zener diode into the Zener diode test area.
  2. Press the locking handle.
  3. Briefly press the multi-function button to initiate the test.

6.3. IR Decoder Function

The LCR-MF9 can decode infrared signals from remote controls.

  1. After a component test is completed, point an infrared remote control at the "IR" test hole on the tester.
  2. Press a button on the remote control.
  3. The tester will display the user code and data code upon successful decoding, along with the corresponding infrared waveform.

If decoding fails, the user code and data code will not be displayed. If you are currently in the tester interface, you cannot enter the infrared decoding interface. If you are already in the infrared decoding interface, the last successful decoding information will remain displayed.

Note: This decoder only supports infrared encoding in Hitachi format. Other formats are not supported.

LCR-MF9 IR Decoder display example
Figure 11: Example of IR decoding results on the LCR-MF9 display.

6.4. Automatic Calibration

For optimal accuracy, periodic calibration is recommended.

  1. Short-circuit the three test sockets in the transistor test area (e.g., using a short wire).
  2. Short press the multi-function button. The tester will automatically calibrate.
  3. During the calibration process, follow any on-screen prompts, such as disconnecting the short wire when instructed. No other operations are required.
LCR-MF9 automatic calibration steps
Figure 12: Visual representation of the automatic calibration process.

6.5. Product Demonstration Video

Watch this video for a quick demonstration of the LCR-MF9's component testing capabilities.

Video 1: LCR-MF9 Multi-function Tester demonstration.

7. Maintenance

7.1. Battery Management

The tester will detect and display the internal lithium battery voltage before each component measurement. If the battery voltage drops below 3.1V, the device will automatically shut down to prevent damage. At this point, please charge the battery using the Micro USB port.

LCR-MF9 display showing 'Charge the battery!'
Figure 13: Low battery warning on the LCR-MF9 display.

7.2. Automatic Shutdown

The tester features an automatic power-off function. After a component test or IR decoding is completed, if no further action is taken, the tester will automatically shut down after a set timeout (default is 30 seconds). The standby power consumption after shutdown is 0 μA.

8. Troubleshooting

If you encounter issues with your LCR-MF9 tester, refer to the following table for common problems and solutions.

QuestionCauseSolution
Cannot power onLithium battery is lowPlease charge until the light turns green
Inaccurate measurementsN/APlease re-calibrate

8.1. Known Limitations and Unsolved Problems

  • Germanium Transistors: The current amplification factor of germanium transistors may be measured as too high due to high residual current. The base-emitter voltage will appear very low in this case.
  • Power Schottky Diodes (e.g., MBR3045PT): The capacitance value in the reverse direction may not be measurable if only one diode is connected, due to a large residual current. Cooling the device may sometimes enable measurement.
  • Triac Gate: The diode function of a triac gate cannot be examined.
  • JFETs: Source and Drain pins may not be detected correctly due to the symmetrical structure of these semiconductors. The display may show the same layout and parameters if the Source and Drain pins are swapped.
  • Output Current/Voltage Limitations: The tester's output current is 6mA and voltage is <5V. High-power IGBTs, thyristors, and Darlington tubes requiring higher current/voltage drive may not be measurable.
  • Inductors: Air core coils and power inductors cannot directly measure inductance. It is recommended to try series connection for appropriate color ring inductance tests.
  • Small Capacitors: For capacitors below 20pF, it is recommended to test them in conjunction with a known 20pF capacitor for more reliable results.

9. User Tips

  • The tester is generally reported to work well and provides accurate readings for common components.
  • Many users appreciate that the device often arrives fully charged and ready for immediate use.
  • Its ease of use makes it a cool and convenient tool for electronics enthusiasts.

10. Warranty and Support

For any technical support, warranty claims, or further inquiries regarding your LCR-MF9 Multi-function Tester, please contact the seller or manufacturer directly. Ensure you retain your purchase receipt for warranty purposes.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.