GlintDeer LCR-MF9

Contents

LCR-MF9 Multi-function Transistor Tester User Manual

Model: LCR-MF9 (T9-1)

1. Product Overview

The GlintDeer LCR-MF9 is a versatile multi-function tester designed for automatic detection and measurement of various electronic components. It features a 1.8-inch TFT LCD display for clear graphical results and includes functions for transistor testing, IR decoding, and more.

LCR-MF9 Multi-function Tester with included accessories
LCR-MF9 Multi-function Tester and accessories.
LCR-MF9 Multi-function Tester with labeled parts: TFT Display, IR receiver window, Test button, Transistor test area, Zener Diode test area, USB charging port.
Key components of the LCR-MF9 Tester.
Video demonstrating various component tests with the LCR-MF9.

2. Safety & Warnings

  • Do not use with incompatible devices / accessories to avoid affecting product performance or damaging related equipment.
  • If the product shows any abnormal conditions such as smoke, unusual noises, or odors, immediately stop using it.
  • This product is not food-related. Keep it away from children and avoid accidental ingestion / touching of sharp parts (if any).
  • Warning: Always be sure to DISCHARGE capacitors before connecting them to the tester! The tester may be damaged before you have switched it on!
  • Warning: We do not recommend using the tester to measure the battery! The battery voltage must be less than 4.5V, otherwise the tester may be damaged!
  • Note: The instrument is active output, please do not use the test line to test the charged circuit board, easy to damage the instrument, the main performance is not to turn on.

3. Specifications

Attribute Name Attribute Value
Semi-finished productYes
Battery Includedno
High-concerned chemicalnone
Is Smart Deviceno
Operating ModeAuto Range
Operating Temperature0 - 40 ℃
Measuring Capacitance Range25pF-100mF
CertificationCE
DIY SuppliesElectrical
Measuring Resistance Range0.01-50MΩ
Measuring Inductance Range0.01mH-20H
OriginMainland China
Brand NameGlintDeer
Dimensions60*90*27MM
DC CurrentESR
AC CurrentMOSFET
DC Voltage3.7V
Display TypeDigital Display
AC Voltagemultimeter
GLINTDEER ModelLCR-MF9

Component Measurement Ranges & Parameters:

Component Type Range Parameter Description
BJT/hFE (DC Current Gain), Ube (Base-Emitter Voltage), Ic (Collector Current), Iceo (Collector Cut-off Current (IB=0)), Ices (Collector short Current), Uf (Forward Voltage of protecting diode)
Diodeforward voltage <4.50VForward voltage drop, junction capacitance, reverse leakage current
Double Diodeforward voltage <4.50VForward voltage
Zener Diode (Transistor Test Area)0.01-4.50VForward voltage drop, reverse breakdown voltage
Zener Diode (KAA Test Area)0.01-20VReverse breakdown voltage
JFETMOSFETCg (Gate Capacitance), Id (Drain Current) at Vgs (Gate to Source Threshold Voltage), Uf (Forward Voltage of protecting)
IGBTMOSFETDrain current Id under Vgs, protection diode forward voltage drop Uf
MOSFETMOSFETTurn-on voltage Vt, gate capacitance Cg, drain resistance Rds, protection diode forward voltage drop Uf
ThyristorGate trigger current <6mAGate turn-on voltage
TriacGate trigger current <6mAGate turn-on voltage
Capacitor25pF-100mFCapacitance Value, Equivalent Series Resistance ESR, Vloss
Resistor0.01-50MΩResistance
Inductor0.01mH-20HInductance, DC Resistance
Battery0.1-4.5VVoltage value, battery polarity

4. Setup

4.1 Initial Preparation

  • Remove all protective films from the device.

4.2 KAA Test Area Activation (for Zener Diodes > 5V)

The KAA test area is turned off by default. To activate it:

  1. Ensure the tester is powered off.
  2. Press and hold the TEST key for approximately 15 seconds.
  3. The screen will display "KAA OFF" changing to "KAA ON" in the lower left corner, indicating the KAA test area is activated.
  4. The setting is automatically saved and does not need to be repeated.

Important Note: The output voltage of the KAA area is 20V. If a capacitor is accidentally placed here, it MUST be discharged before being placed into the transistor test area. Failure to discharge can immediately damage the instrument, potentially damaging test area pins or causing the machine to shut down permanently.

5. Operating Instructions

5.1 Power On & Basic Measurement

In the power-off state, a short press of the multi-function key will turn on the tester and initiate an automatic measurement.

LCR-MF9 display showing 'Testing...' and battery voltage, indicating power on and measurement interface.
Power on and measurement interface.

5.2 Detecting Transistors and Other Components

To test a component:

  1. Ensure the tester is powered off or a previous test is completed.
  2. Insert the test element into the transistor test area of the test seat. The tester will automatically identify the pins.
  3. Press the locking handle to secure the component.
  4. Short press the multi-function key. The tester will automatically measure and graphically display the results.

The instrument is equipped with three lines for testing. For capacitors, it is recommended to insert them directly into the test area for more accurate results. Always discharge capacitors before testing.

LCR-MF9 display showing various component test results including Capacitor, Inductor, Resistor, Battery, Thyristor, Triac, N-JFET, Diode.
Examples of component test results.
LCR-MF9 display showing various transistor test results including BJT-NPN, BJT-PNP, N-E-MOS, P-E-MOS, N-D-MOS, N-E-IGBT, P-JFET.
Examples of transistor test results.

5.3 Detecting Zener Diodes

For Zener diodes, especially those higher than 5V, use the dedicated Zener diode test area (KAA test area, refer to Setup section for activation).

  1. Ensure the tester is powered off or a previous test is completed.
  2. Insert the Zener diode into the Zener diode test area.
  3. Press the locking handle.
  4. Briefly press the multi-function button to start the test.
LCR-MF9 Zener diode test area warning: Do not put components in the Transistor test area, otherwise the Zener diode cannot be tested!
Warning regarding Zener diode placement.

5.4 IR Decoder Function

The IR decoder supports Hitachi IR coding and displays IR waveforms.

  1. After a component test is completed, point an infrared remote control at the "IR" test hole of the tester.
  2. Press a button on the remote control.
  3. The tester will display the user code and data code upon successful decoding, along with the corresponding infrared waveform.

If decoding fails, the user code and data code will not be displayed. If you are in the tester interface, you cannot enter the infrared decoding interface. If you are already in the infrared decoding interface, the last successful decoding information will remain displayed.

LCR-MF9 IR decoder display showing UserCode and DataCode, and a waveform.
IR decoder display.

6. Maintenance

6.1 Automatic Calibration

To ensure measurement accuracy, perform automatic calibration:

  1. Short-circuit the three test sockets (1, 2, and 3) in the transistor test area.
  2. Short press the multi-function button. The tester will automatically calibrate.
  3. During calibration, follow the on-screen prompts, such as disconnecting the short wire when instructed.
LCR-MF9 self-test mode progress bar during calibration, showing 'Calibrating', 'Isolate Probes!', and 'Selftest End'.
Self-test/calibration progress.

6.2 Battery Charging

The LCR-MF9 has a built-in rechargeable Li-ion battery. The charging interface is a standard Micro USB. Use an external 5V power supply or USB power supply for charging.

LCR-MF9 charging indicator note: red means charging, green means charging is complete.
Charging indicator explanation.

6.3 Battery Voltage Detection

Before each component measurement, the built-in lithium battery voltage is detected and displayed. If the battery voltage drops below 3.1V, the tester will automatically shut down, indicating that it needs to be charged.

LCR-MF9 display showing 'Charge the battery!' when voltage is low.
Low battery warning display.

6.4 Automatic Shutdown

The tester will automatically shut down after a set timeout (default 30 seconds) if no activity is detected after a component test or IR decoding. Standby power consumption is 0 UA after shutdown.

7. Troubleshooting

7.1 Common Issues & Solutions

Question Cause Solution
Cannot power onLithium battery is lowPlease charge until the light turns green
Inaccurate measurementsPlease re-calibrate

7.2 Known Errors and Unsolved Problems

  • The current amplification factor of germanium transistors can be measured too high due to high residual current. In this case, the base-emitter voltage will be very low.
  • Capacity value in reverse direction for Power Schottky Diodes such as MBR3045PT cannot be measured if only one diode is connected. The reason is a too big residual current of this diode. Sometimes the measurement is possible by cooling down the device (with cooling spray for example).
  • The diode function of a triac gate cannot be examined.
  • The Source and Drain pins cannot be detected correctly with JFETs. The reason is the symmetrical structure of these semiconductors. You can notice this problem if the display shows the same layout with the same parameters when the Source and Drain pins are swapped.
  • The output current of the tester is 6mA / voltage <5V. High-power IGBTs, thyristors, and Darlington tubes that require higher current/higher voltage drive may not be measured.
  • Air core coils and power inductors cannot directly measure inductance. It is recommended to try series connection.
  • For capacitors below 20pF, it is recommended to test with a 20pF capacitor for appropriate color ring inductance test.

8. User Tips

  • For more accurate measurements, consider performing a calibration if you notice inconsistencies.
  • If the system freezes during a component check, disconnecting and reconnecting the battery may help reset the device.

9. Warranty & Support

Manufacturer & EU Representative Information:

  • Country: China
  • Telephone: +86-13417026232
  • Email: xinhui0518@163.com
  • Responsible Person: Ouyanghui
  • EU Representative: eVatmaster Consulting GmbH
  • EU Representative Address: Bettinastr. 30, 60325 Frankfurt am Main, Germany
  • EU Representative Email: contact@evatmaster.com
  • EU Representative Telephone: +49-6995179070

For further assistance, please contact the manufacturer or the EU representative using the provided details.

A detailed user manual in PDF format is also available: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.