GODIAG GT110

Contents

GODIAG GT110 User Manual

VW CAN-Bus UDS 4th Generation IMMO System Test Platform Cable

Product Overview

The GODIAG GT110 for VW Skoda Seat CAN-Bus UDS 4th generation IMMO system test platform cable supports VW, Skoda, Seat, and other models. It performs offline POGO PIN data reading and writing, specifically for dashboards key programming (including Boot Probe) of all UDS systems from Volkswagen, Skoda, and Seat.

This device displays the current working voltage and current, features a power switch, a simulated ignition switch, and a buzzer to indicate ignition start and shut down.

It supports CANH UDS communication indication, CR2032 remote key battery detection, key and IMMO instrument synchronization tests, intelligent IMMO system emergency start area induction detection, IMMO combination instrument offline diagnosis, instrument IMMO data reading and writing, instrument mileage repair, and key matching, among other functions.

The GODIAG GT110 is compatible with various diagnostic devices such as HEX V2, VAGCOM VCDS 5053, VAS5054A, VAS6154, SUPER VAG K+CAN, Obdstar, Lonsdor, AVDI, ZEDFULL, VVDI2, Key Tool Plus, X300 DP Plus, Lonsdor, SUPER VAG, and AUTEL.

Key Features

  • Uses POGO PIN to read and write data to the dashboard.
  • Enables offline connection to the dashboard for conversion to standard OBD2.
  • Performs key chip and instrument synchronization tests.
  • Features an independent power switch.
  • Simulates ignition switch functionality.
  • Displays current working voltage.
  • Includes CR2032 remote key battery detection.
  • Displays current instrument working current.
  • Equipped with a CANH UDS communication indicator light.
  • Comes with a key induction adapter with light.
  • The POGO PIN design ensures stable holding and prevents cable damage.

Product Comparison

The GODIAG GT110 offers enhanced features compared to other brands:

Feature GODIAG GT110 Other Brands
Model GODIAG GT110 Other Brands
OBD2 √ √
FOR BENCH √ √
POGO pin √ with extended pogo pin √ with short pogo pin
Voltage display √ ×
Current display √ ×
IMMO Synchronization Test √ ×
Main power switch √ ×
CAN communication display √ ×
Key recognition coil √ Smart key emergency start test for all vehicles ×
Product Comparison Table
Comparison of GODIAG GT110 features against other brands.

Setup and Connections

Before operating the GODIAG GT110, familiarize yourself with its components and connection points.

Video demonstrating the GODIAG GT110 components and basic setup.
GODIAG GT110 main unit and cables
The GODIAG GT110 main unit with its various cables and connectors.
Close-up of GODIAG GT110 device with display
Close-up view of the GODIAG GT110 device, showing the display and control buttons.
POGO PIN probe
The POGO PIN probe, used for direct data reading and writing on dashboard chips.
IMMO IV UDS connector
The IMMO IV UDS connector, part of the GT110 cable assembly.
Key induction adapter
The key induction adapter, used for key chip detection and matching.
Power and ignition switch
Close-up of the power input and ignition switch on the GT110.

Operating Instructions

Using POGO PIN to Read FLASH Data

  1. Connect Power Supply: Connect the power supply to the GT110. Ensure the power switch is initially OFF.
  2. Press Ignition Switch: Press the IGN ignition switch first (ensure it is turned ON).
  3. Connect GT110 to Instrument: Connect the GT110 cable to the vehicle's instrument cluster.
  4. POGO PIN connection diagram for dashboard
    Diagram showing how to connect the POGO PIN to the dashboard. Note that some chip boards do not require cover removal.
  5. Locate POGO PIN Connection Point: Find the specific POGO PIN connection point on the corresponding instrument's chip board and connect it with the POGO PIN probe.
  6. POGO PIN connection to dashboard circuit board
    Connecting the POGO PIN probe to the dashboard circuit board for data access.
  7. Activate Read/Write Mode: Turn on the main power switch for approximately 3-5 seconds. If the instrument's ABS light starts flashing, it indicates that the POGO PIN read and write mode has been successfully entered.

Note: During this process, the POGO PIN probe must be kept firmly pressed on the POGO PIN point to ensure stable connection.

VW GOLF Key Chip Matching with GODIAG GT110 & VVDI2

  1. Initial Connection: Connect the GODIAG GT110, VVDI device, computer, and the vehicle's instrument cluster as illustrated in the figure below.
  2. Connection diagram for key matching with GT110, VVDI, computer, and dashboard
    Connection diagram for performing key chip matching using GODIAG GT110 and VVDI2 software.
  3. Power Connection: Connect a 12V power supply to the GODIAG GT110.
  4. Connecting 12V power to GT110
    Step-by-step image showing the connection of the 12V power supply to the GT110 device.
  5. Activate Power and Ignition: Press the main power switch (labeled '1') and then the ignition switch (labeled '2') on the GT110. After pressing the ignition switch, the dashboard should display 'SAFE', and the light on the sensor adapter will flash for a long time before turning off, indicating that no matching key chip has been identified yet.
  6. Pressing power and ignition switches on GT110
    Illustration of pressing the power and ignition switches on the GODIAG GT110.
  7. Launch VVDI2 Software: Open the VVDI2 software on your computer and click on the 'VW' option.
  8. VVDI2 software interface showing VW selection
    Screenshot of the VVDI2 software interface, highlighting the VW selection for vehicle diagnostics.
  9. Connect to Instrument: In the VVDI2 software, navigate to "Diagnostic" >> "Diagnostic Unit" >> "17 Instruments" >> "Connect". This allows you to read instrument information and clear fault codes.
  10. Initiate Key Learn: After exiting the "Diagnostic" section, select "Key Learn" >> "4th immobilizer system-VW/Skoda/Seat" >> "Auto detect type".
  11. Read IMMO Data: Click "Diag" >> "Read IMMO Data" >> "Read EEPROM/FLASH" >> "Make Dealer Key" >> "Next".
  12. Insert Super Chip: Follow the prompts in the software to insert the Xhorse VVDI super chip. If the chip has been previously used, it must be erased first.
  13. Complete Matching: After inserting the chip, click "OK" to continue. The key chip matching process should then be successful.
  14. Test New Chip: Put the newly generated chip into the induction adapter.
  15. Final Verification: Press the main power switch (1) and ignition switch (2) in order. The light on the induction adapter should flash quickly and then turn off immediately, and the instrument panel will display the specific mileage, confirming successful chip matching.

Intelligent IMMO System Emergency Start Area Induction Detection

To use this feature, press the vehicle's start switch and bring the device's key identifier close to a specific area. If the key identifier light flashes or lights up, it indicates that this is the vehicle's key emergency start sensing area. If the customer's smart key is out of power, simply place the dead smart key in this sensing area to start the vehicle.

Car IMMO Start and Start Key Chip Detection Test Result Analysis

  • Light flashes then goes out: Indicates that the IMMO chip and the chip key are working properly.
  • Light flashes for a long time: Indicates that the chip key and the vehicle's IMMO system do not match, and the chip key needs to be re-matched.
  • Light does not flash: Indicates that the vehicle's IMMO system is faulty. Please check the vehicle's IMMO system.

Maintenance

To ensure the longevity and optimal performance of your GODIAG GT110, follow these maintenance guidelines:

  • Keep the device clean and dry. Wipe with a soft, dry cloth.
  • Avoid exposing the device to extreme temperatures, humidity, or direct sunlight.
  • Store the device and its accessories in a safe place when not in use to prevent physical damage.
  • Regularly inspect cables and connectors for any signs of wear or damage. Replace if necessary.

Troubleshooting

If you encounter issues while using the GODIAG GT110, refer to the following common problems and solutions:

  • Issue: Key chip and IMMO system mismatch.
    Solution: The light on the key identifier flashes for a long time. This indicates that the chip key and the vehicle's IMMO system do not match. You will need to re-match the chip key following the detailed instructions in the 'VW GOLF Key Chip Matching' section.
  • Issue: IMMO system faulty.
    Solution: The light on the key identifier does not flash at all. This suggests a fault within the vehicle's IMMO system itself. It is recommended to perform a comprehensive diagnostic check on the vehicle's IMMO system.
  • Issue: POGO PIN read/write mode not entered.
    Solution: Ensure the POGO PIN probe is firmly and consistently pressed against the correct connection point on the dashboard. Also, verify that the main power switch is held for the required 3-5 seconds until the ABS light on the instrument flashes, confirming entry into read/write mode.
  • Issue: Xhorse VVDI super chip not recognized during matching.
    Solution: If a super chip has been used previously, it must be erased before it can be programmed for a new vehicle. Ensure the chip is clean and properly inserted into the VVDI device.

Specifications

  • Brand Name: GODIAG
  • Model: GT110
  • Origin: Mainland China
  • Product Dimensions (approx.): 14 cm (Length) x 8 cm (Width) x 3 cm (Height)
  • Product Weight (approx.): 0.2 kg
  • Warranty: One year
  • High-concerned chemical: None

User Tips

  • Always ensure the POGO PIN is securely pressed during data reading to prevent incomplete data transfer or errors.
  • Before attempting new key matching, always erase a used Xhorse VVDI super chip to avoid conflicts and ensure successful programming.
  • Double-check all cable connections before powering on the device to prevent short circuits or damage.

Warranty and Support

The GODIAG GT110 comes with a one-year warranty from the date of purchase, covering manufacturing defects.

For technical support, inquiries, or assistance, please contact:

A PDF version of this user manual is available for download and reference. You can find it at: GODIAG GT110 User Manual (PDF)

Accessories

The GODIAG GT110 package includes the following items:

  • 1 x GODIAG GT110 FOR VW Skoda Seat Test Platform Cable
  • 1 x User Manual (PDF)
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.