M5Stack U032-V11

Contents

M5Stack Official GPS/BDS Unit v1.1 (ATGM336H-6N) User Manual

Model: U032-V11

1. Introduction

The M5Stack Official GPS/BDS Unit v1.1 (ATGM336H-6N) is a Global Navigation Satellite System (GNSS) positioning and navigation unit. It integrates the high-performance AT6668 navigation chip and a MAX2659 signal amplifier, along with a built-in ceramic antenna. This unit is designed to provide precise and reliable satellite positioning services by supporting multiple satellite navigation systems including GPS, QZSS, BD2, BD3, GAL, and GLO.

The unit communicates via UART serial communication, with a default baud rate of 115200bps.

M5Stack GPS Unit v1.1 with Grove cable
Figure 1: M5Stack GPS Unit v1.1 and included Grove cable.

2. Package Contents

Please check the package for the following items:

  • Unit GPS v1.1 x 1
  • HY2.0-4P Grove cable (20cm) x 1
M5Stack GPS Unit v1.1 packaging
Figure 2: Contents of the M5Stack GPS Unit v1.1 package.

3. Setup

3.1 Connection

Connect the M5Stack GPS Unit v1.1 to a compatible M5Stack host device using the provided HY2.0-4P Grove cable. The unit features a PORT. C. UART interface with pins for GND, 5V, RXD, and TXD. Ensure the cable is securely connected to the corresponding Grove port on your M5Stack host.

M5Stack GPS Unit v1.1 UART interface
Figure 3: Close-up of the GPS Unit v1.1 showing the PORT. C. UART interface.

3.2 Power On

Once connected, power on your M5Stack host device. The GPS unit will receive power through the Grove interface.

4. Operation

The GPS Unit v1.1 is designed for global positioning and navigation. For optimal performance and accurate satellite acquisition, outdoor use is recommended.

4.1 Satellite Acquisition

Upon powering on, the unit will begin searching for satellites. The integrated AT6668 solution supports multi-satellite joint positioning (GPS+QZSS+BD2+BD3+GAL+GLO) for increased accuracy and faster lock times. A cold start typically takes 23 seconds, while a hot start can be as quick as 1 second.

Video 1: Demonstration of the M5Stack GPS Unit v1.1 acquiring satellite data with an M5Stack host device. Outdoor use is recommended for best results.

4.2 Data Output

The GPS unit outputs positioning data via its UART interface. The default communication settings are 115200bps, 8 data bits, no parity, and 1 stop bit (8N1). The data protocol used is NMEA0183 4.1. You can process this data using your M5Stack host device for various applications.

4.3 Typical Applications

This unit is suitable for a wide range of applications requiring precise location data, including:

  • IoT positioning devices
  • Vehicle positioning and navigation
  • Bus stop announcements
  • Drones & Robots
Examples of M5Stack GPS Unit v1.1 applications
Figure 4: Various application scenarios for the GPS Unit v1.1.

5. Specifications

The following table details the technical specifications of the M5Stack GPS Unit v1.1:

SpecificationParameter
SoCATGM336H-6N Module@AT6668
Channels50 channels
CommunicationUART communication, default 115200bps@8N1
Positioning Accuracy<1.5m (CEP50)
Positioning Update RateUp to 10Hz
ProtocolNMEA0183 4.1
SensitivityTracking: -162dBm, Acquisition: -160dBm, Cold Start: -148dBm
Start TimeCold Start: 23 seconds, Hot Start: 1 second
Dimensions48mm x 24mm x 8mm (1.88in x 0.94in x 0.31in)
Weight12.3g
M5Stack GPS Unit v1.1 detailed specifications
Figure 5: Detailed specifications of the GPS Unit v1.1.
M5Stack GPS Unit v1.1 dimensions
Figure 6: Physical dimensions of the GPS Unit v1.1.
M5Stack GPS Unit v1.1 weight
Figure 7: Weight of the GPS Unit v1.1.

6. Maintenance

To ensure the longevity and optimal performance of your M5Stack GPS Unit v1.1, please follow these maintenance guidelines:

  • Keep the unit dry and away from moisture.
  • Avoid exposing the unit to extreme temperatures or direct sunlight for prolonged periods.
  • Handle the unit with care to prevent physical damage.
  • Do not attempt to disassemble the unit, as this may void the warranty and cause damage.
  • Clean the exterior with a soft, dry cloth if necessary.

7. Troubleshooting

If you encounter issues with your GPS Unit v1.1, consider the following:

  • No Satellite Lock: Ensure the unit is used outdoors with a clear view of the sky. Obstructions like buildings or dense foliage can interfere with satellite signals.
  • Incorrect Data: Verify that the UART connection is secure and that your M5Stack host device is configured with the correct baud rate (115200bps) and data protocol (NMEA0183 4.1).
  • No Power: Check the Grove cable connection and ensure your M5Stack host device is powered on correctly.
  • Unit Not Recognized: Confirm that the Grove cable is properly seated in both the GPS unit and the M5Stack host.

For more detailed troubleshooting or specific technical support, please refer to the official M5Stack documentation and community forums.

8. User Tips

  • Outdoor Use: For the most accurate and fastest satellite acquisition, always use the GPS unit outdoors with an unobstructed view of the sky.
  • Power Management: When integrating into battery-powered projects, consider the power consumption of the GPS unit and optimize your code for efficient operation.
  • Data Parsing: Familiarize yourself with the NMEA0183 4.1 protocol to effectively parse and utilize the positioning data in your applications.

9. Warranty & Support

For warranty information, technical documentation, tutorials, and community support, please visit the official M5Stack website. The website provides comprehensive resources to help you get the most out of your M5Stack products.

9.1 Accessing Tutorials and Documentation

To find tutorials and detailed documentation for your GPS Unit v1.1, follow these steps:

  1. Visit m5stack.com.
  2. Click on the "DOCUMENT" section.
  3. Search for your product (GPS Unit v1.1 or U032-V11).
  4. Scroll down to find relevant information, including compatibility details.
Steps to access M5Stack tutorials online
Figure 8: Visual guide to accessing M5Stack online tutorials and documentation.

© 2024 M5Stack. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.