DemonFX SIM-AMP

Contents

Demonfx SIM-AMP Simplifier Bass Station User Manual

Preamp Simulator, Power Amp SIM, Stereo Cab SIM & DI Out for Electric Bass

1. Introduction

The Demonfx SIM-AMP Simplifier Bass Station is a versatile all-analog bass platform designed for direct connection to a Front of House (FOH) system or for recording high-quality bass tones without compromise. It integrates a bass preamp, power amp simulation, stereo cabinet simulation, and DI outputs into a compact unit.

This device is based on the DSM & Humboldt SIMPLIFIER BASS STATION, offering a comprehensive solution for bass players seeking professional sound and flexible routing options.

2. Setup

2.1 Powering Up

Before connecting the power supply, ensure that any receiving devices (PA, audio interface, headphones, etc.) are turned down to avoid sudden 'pop' noises.

  • Use a 9V to 12V DC regulated adapter.
  • The power supply must have a minimum current rating of 80 mA. Higher current ratings are acceptable.
  • Ensure the power supply has a center negative polarity.
  • WARNING: Do NOT use center positive power supplies. This may damage the unit and void the warranty. Always verify polarity before connecting.
  • Avoid daisy-chaining the power supply with high-current digital units to ensure a clean voltage source.

2.2 Connections

Familiarize yourself with the input and output jacks on your SIM-AMP Bass Station:

Top and front view of Demonfx SIM-AMP Bass Station showing all controls and 1/4 inch jacks

Figure 1: Top and Front Panel Overview

  • Input Jack: Connect your electric bass instrument here.
  • Parallel FX Send: This output carries the signal directly from the input, bypassing the preamp. Use this for effects you wish to apply to the 'clean' signal chain.
  • Parallel FX Return: Connect the output of effects used in the parallel signal chain here.
  • Preamp FX Send: This output carries the signal after the preamp stage. Use this for effects you wish to apply specifically to the preamp's processed signal.
  • Preamp FX Return: Connect the output of effects used in the preamp signal chain here.
  • TRS Out (Output/Thru Output): Carries the main output signal (blended preamp + parallel signal) or the bypassed input signal, depending on settings.
Rear view of Demonfx SIM-AMP Bass Station showing XLR DI outputs and power input

Figure 2: Rear Panel with XLR Outputs and Power Input

  • DI OUT: Provides a balanced XLR output of the main signal (preamp + parallel blend), suitable for connecting to a mixing console or audio interface.
  • DI PARALLEL: Provides a balanced XLR output of only the parallel signal chain (including its FX loop and LPF), useful for sending a clean signal to a separate channel.
  • Aux In: Connect an external audio device (e.g., MP3 player, phone) here for practice or monitoring. This signal is routed only to the headphone output and does not pass through the main outputs.
  • Headphone Out: Connect your headphones here for silent practice or monitoring.

3. Operation

3.1 Preamp Section Controls

  • Gain: Adjusts the input gain of the preamp. Setting it above 70% can produce a classic SVT-style overdrive.
  • Volume: Controls the master output volume level of the preamp.
  • Mid Freq (Mid Select): A 3-way switch to select the center frequency for the Mid control: 400Hz, 900Hz, or 1500Hz.
  • High: Controls the high-frequency band, offering +/- 15dB at 3.5kHz (shelving).
  • Mid: Controls the midrange band, offering +/- 15dB (bandpass), with the frequency determined by the Mid Freq switch.
  • Bass: Controls the low-end frequencies, offering +/- 15dB at 80Hz (shelving).

3.2 Blend Section Controls

This section allows you to mix the preamp signal with the parallel signal and integrate the cabinet simulation.

  • Preamp Blend: Blends the preamp signal and the parallel signal into the main output. Start with this control at 100% (preamp only) and gradually blend in the parallel signal to achieve your desired mix.
  • Cabsim Blend (Dry/Wet): Blends the analog cabinet simulation in or out of the main signal, allowing for different textures and low-end responses.
  • Parallel LPF (Low Pass Filter): A 3-way toggle switch that applies a 2-pole low pass filter to the parallel signal.
    • 100Hz: Preserves deep low end while filtering out higher harmonic content.
    • OFF: Disables the low pass filter.
    • 500Hz: Preserves deep low end and low-mids in the parallel signal chain.

3.3 Cabinet Simulation Controls

  • Mic Position (Off Axis/Center): Simulates the placement of a microphone relative to a speaker cone. Adjusts the amount of high-end roll-off. Center positions typically sound best for clean tones, while off-axis positions are often preferred for distorted tones.
  • Resonance: Adjusts the low-end resonance of the simulated cabinet.
  • Cab Size Switch: Selects between three distinct cabinet types:
    • 4x10 Vented: A modern standard with extended flat low-end response and bright drivers.
    • 8x10 Sealed: Provides a huge-sounding resonant low-end cabinet with modern speakers.
    • 1x15 Vented: Offers a warm and well-rounded tone with extended low end, and creamier, less piercing highs.
  • Speaker Color Switch (Bright/Modern/Warm): Simulates different speaker materials and geometries, affecting dynamics and midrange response.
    • Bright: Simulates aluminum cone speakers with a distinct mid-high bite.
    • Modern: Provides a flatter response with enhanced highs and lows.
    • Warm: Emulates vintage speakers with a clearer mid response and smoother highs.

3.4 Other Switches and Controls

  • Parallel Phase (Normal/Inv): A toggle switch to invert the phase of the parallel signal. Useful for correcting phase cancellation issues that can occur when blending signals from certain pedals.
  • GND Lift (Ground/Lift): Disconnects the ground connection from the XLR outputs. Use this switch if you experience hum or ground loop noise when connecting to external devices.
  • Phones Level (Headphone Level): Controls the output volume for the headphone jack.
  • Passive/Active Input Switch: Adjusts the input gain for your bass.
    • Active: Lowers the gain for basses with hot active pickups.
    • Passive: Provides a slight +6dB boost to compensate for lower-level passive bass signals.

4. Features Overview

  • All-analog signal path for authentic tone.
  • Bass Preamp stage based on the classic Ampeg SVT® amplifier.
  • Highly flexible 3-band EQ with switchable semi-parametric mid control (400Hz, 900Hz, 1500Hz).
  • Dedicated parallel signal path with selectable Low Pass Filter (100Hz, OFF, 500Hz).
  • Dual independent FX loops for both preamp and parallel signal chains.
  • Analog Cabinet Simulation inspired by the Omnicabsim® by DSM Noisemaker.
  • Three distinct cabinet types: 4x10 Vented, 8x10 Sealed, and 1x15 Vented.
  • Speaker color options (Bright, Modern, Warm) to fine-tune speaker response.
  • Mic Position and Resonance controls for detailed cabinet tone shaping.
  • Multiple output options: TRS Out, Balanced XLR DI OUT, and Balanced XLR DI PARALLEL.
  • Auxiliary input and Headphone output for practice and monitoring.
  • Ground Lift switch to eliminate hum.
  • Phase control for optimal signal blending.
  • Active/Passive input switch for instrument compatibility.

5. Specifications

ParameterValue
Current Consumption50mA to 100mA (if Headphone out is used)
Supply Voltage9V - 12V DC
PolarityCenter Negative
Input Impedance1 Meg Ohm
TRS Output Impedance100 Ohm
DI Output Impedance120 Ohm
Send Output Impedance100 Ohm
Return Input Impedance1 Meg Ohm
Headphone Power120mW @ 32 Ohm
Width115 mm (4.53 in)
Height65 mm (2.55 in)
Depth55 mm (2.16 in)
Weight430 g (0.94 lb)

6. Troubleshooting

  • No Sound or Weak Signal:
    • Check all cable connections (input, output, FX loops).
    • Ensure the power supply meets the specified voltage, current, and polarity requirements.
    • Verify the 'Volume' and 'Preamp Blend' controls are not set too low.
    • If using an active bass, ensure the 'Passive/Active' switch is set to 'Active'. If using a passive bass, ensure it's set to 'Passive' for a slight boost.
  • Hum or Noise:
    • Engage the 'GND Lift' switch on the rear panel if connecting to an external device via XLR outputs.
    • Ensure your power supply is regulated and not shared with noisy digital pedals.
    • Try a different power outlet or power supply.
  • Phase Cancellation Issues (Thin Sound, Loss of Low End):
    • If blending the preamp and parallel signals, or using certain effects, adjust the 'Parallel Phase' switch to 'Inv' to correct potential phase issues.
  • Distorted or Unwanted Overdrive:
    • Reduce the 'Gain' control in the Preamp section.
    • If using an active bass, ensure the 'Passive/Active' switch is set to 'Active'.

7. User Tips

  • Experiment with Blending: The 'Preamp Blend' and 'Cabsim Blend' controls are powerful tools. Start with the preamp signal at 100% and gradually introduce the parallel signal to find the perfect balance of clarity and grit. Similarly, experiment with the Cabsim blend to add warmth or definition.
  • Utilize the Dual FX Loops: The independent FX loops for the preamp and parallel signals offer immense flexibility. Place modulation or time-based effects in the preamp loop for a more processed sound, and use the parallel loop for effects that benefit from a clean signal foundation.
  • Phase Awareness: If your tone sounds thin or lacks punch when blending signals, try flipping the 'Parallel Phase' switch. This can often resolve subtle phase issues that degrade sound quality.
  • Input Sensitivity: Remember to use the 'Passive/Active' switch to match your bass's output level. This ensures optimal signal-to-noise ratio and prevents unwanted clipping or a weak signal.
  • Direct Recording: For direct recording, connect the 'DI OUT' to your audio interface. Experiment with the 'Cabsim Blend' and 'Mic Position' controls to achieve a studio-quality bass tone without needing a physical amp or microphone.

8. Warranty and Support

For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact your retailer. Keep your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.